S78-IVTI410EBluetooth module 4.0 LE

i410e Datasheet April 12, 2013 Version 1.7 BlueSoleil EcoSystem BlueSoleil EcoSystem BlueSoleil EcoSystem BlueSoleil EcoSystem i410e Datasheet 2 / 28 VERSION HISTORY REVISION AMENDMENT DATE AUTHOR 1.0 Initial version 2012-10-7 Zhu Yong 1.1 Modify 3, 8, 10 section 2012-10-9 Wan Zhifu Huang Ruixue 1.2 1. Update power consumption; 2. Change PIO4 to GND. 2012-10-29 Li Li 1.3 1. Update power consumption; 2. Update format. 2012-11-29 Li Li 1.4 Update package information. Refer to the chapter 10. 2012-12-12 Li Li 1.5 Update Figure 1 BlueSoleil i410e and Figure 8 i410e Footprint. 2012-12-22 Li Li 1.6 Add FCC, IC, CE certificate 2013-4-3 Li Li 1.7 Add external antenna interface. 2013-4-12 Wan zhifu Li Li BlueSoleil EcoSystem BlueSoleil EcoSystem BlueSoleil EcoSystem BlueSoleil EcoSystem i410e Datasheet 3 / 28 Contents 1 Block Diagram ........................................................................................................................... 6 2 Electrical Characteristics ........................................................................................................... 7 2.1 Absolute Maximum Ratings .......................................................................................... 7 2.2 Recommended Operating Conditions ........................................................................... 8 2.3 Input/output Terminal Characteristics.......................................................................... 8 2.3.1 Switch-mode Regulator ..................................................................................... 8 2.3.2 Low-voltage Linear Regulator ............................................................................ 9 2.3.3 Digital Terminals ................................................................................................ 9 2.3.4 AIO ..................................................................................................................... 9 2.3.5 ESD Protection ................................................................................................. 10 2.4 Current Consumption .................................................................................................. 10 2.5 Radio Characteristics ................................................................................................... 10 2.5.1 RF Ports ........................................................................................................... 10 2.5.2 RF Receiver ...................................................................................................... 11 2.5.3 RF Transmitter ................................................................................................. 11 2.5.4 Bluetooth Radio Synthesizer ............................................................................ 11 2.5.5 Baseband ......................................................................................................... 11 3 Pin Description ........................................................................................................................ 12 4 Physical Interfaces ................................................................................................................... 15 4.1 UART Interface ............................................................................................................ 15 4.2 SPI Interface ................................................................................................................ 15 5 Software Stacks ....................................................................................................................... 16 5.1 BlueSoleil Stack ........................................................................................................... 17 6 Re-flow Temperature-time Profile........................................................................................... 17 7 Reliability and Environmental Specification ............................................................................ 19 7.1 Temperature test ........................................................................................................ 19 7.2 Vibration Test .............................................................................................................. 19 7.3 Desquamation Test ..................................................................................................... 19 7.4 Drop Test ..................................................................................................................... 19 7.5 Packaging Information ................................................................................................ 19 8 Layout and Soldering Considerations ...................................................................................... 20 8.1 Soldering Recommendations ...................................................................................... 20 8.2 Layout Guidelines ........................................................................................................ 20 9 Physical Dimensions ................................................................................................................ 21 10 Package............................................................................................................................ 23 11 Certification ..................................................................................................................... 25 11.1 Bluetooth ................................................................................................................ 25 11.2 CE 0700.................................................................................................................... 25 BlueSoleil EcoSystem BlueSoleil EcoSystem BlueSoleil EcoSystem BlueSoleil EcoSystem i410e Datasheet 4 / 28 11.3 FCC .......................................................................................................................... 25 11.4 IC ..........................................…

Text truncated - open the document above for the full version.

Request for Modular Approval FCC ID: S78‐IVTI410E & IC: 11004A‐IVTI410E Item Requirements EUT 1 Have its own RF shielding Device is equipped with metal shielding to cover RF section. Refer to external and photos. 2 Have buffered modulation/data inputs (if such inputs are provided) All inputs to the modules are buffered through logic and microprocessor inputs(CSR1000) 3 Have its own power supply regulation Module chipset incorporates voltage regulation to transceiver circuitry 4 Meet the antenna requirements of section 15.203 The device has a ceramic antenna. 5 Demonstrate compliance in a stand‐alone configuration Device is tested in a test fixture in a standalone configuration 6 The licensed module must have a FCC ID label on the module itself. That FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: Contains “FCC ID: S78‐IVTI410E” & “IC: 11004A‐IVTI410E” FCC ID & IC label format will be included in the filling. 7 The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements. Please refer to “User Manual” Exhibit 8 The module must comply with RF exposure requirements. See FCC Rules. Spread Spectrum transmitters must comply with RF exposure limits in 15.247. RF exposureevaluation is exempted because of low output power (EIRP: 0.965mW). Thank you for your attention to this matter. Yours Sincerely, Ivy Zhu Certification Manager

External Photos 1. EUT full view with accessories 2. EUT front view with shield 3. EUT rear view

FCC ID: S78-IVTI140E IC: 11004A-IVTI140E Label Size: 25mm*13mm Label Location

Internal Photos 1. EUT front view without shield

SZ13020021W03 Page 2 of 38 DIRECTORY 1. GENERAL INFORMATION .................................................................................................... 3 1.1. EUT Description ....................................................................................................................... 3 1.2. Test Standards and Results ........................................................................................................ 4 1.3. Facilities and Accreditations ..................................................................................................... 5 2. 47 CFR PART 15C AND RSS-210 REQUIREMENTS ........................................................... 6 2.1. Antenna requirement ................................................................................................................. 6 2.2. Peak Output Power.................................................................................................................... 6 2.3. Average power .......................................................................................................................... 9 2.4. 6dB Bandwidth ....................................................................................................................... 10 2.5. 99% Bandwidth ....................................................................................................................... 13 2.6. Conducted Spurious Emissions and Band Edge ..................................................................... 16 2.7. Power spectral density (PSD) ................................................................................................. 20 2.8. Restricted Frequency Bands.................................................................................................... 23 2.9. Conducted Emission ............................................................................................................... 27 2.10. Radiated Emission................................................................................................................... 29 2.11. RF exposure evaluation ........................................................................................................... 38 Change History Issue Date Reason for change 1.0 April 3, 2013 First edition 2.0 July 2, 2013 Second edition SZ13020021W03 Page 3 of 38 1. General Information 1.1. EUT Description EUT Type ............................. : Bluetooth Module Serial No. .............................. : (n.a, marked #1 by test site) Hardware Version ................. : 1.0 Software Version .................. : Applicant .............................. : Manufacturer ........................ : 4.0 IVT Corporation 5/F, Zhongguancun Fazhan Building, No. 12, Shangdi Xinxi Road, Haidian District, Beijing, 100085 China IVT Corporation 5/F, Zhongguancun Fazhan Building, No. 12, Shangdi Xinxi Road, Haidian District, Beijing, 100085 China Frequency Range .................. : The frequency range used is 2402MHz - 2480MHz (40 channels, at intervals of 2MHz); Modulation Type .................. : GFSK Antenna Type ........................ : Ceramic Antenna Antenna Gain ........................ : 2.0dBi Note 1: The EUT is Bluetooth Module, it contain Bluetooth 4.0 LE Module operating at 2.4GHz ISM band; the frequencies allocated for the Bluetooth 4.0 LE is F(MHz)=2402+2*n (0<=n<=39). The lowest, middle, highest channel numbers of the Bluetooth Module used and tested in this report are separately 0 (2402MHz), 19 (2440MHz) and 39 (2480MHz). Note 2: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. SZ13020021W03 Page 4 of 38 1.2. Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart C and RSS-210 (Bluetooth, 2.4GHz ISM band radiators) for the EUT FCC/IC ID Certification: No. Identity Document Title 1 47 CFR Part 15 (10-1-09 Edition) Radio Frequency Devices 2 RSS-GEN:Issue 3, December 2010 General Requirements and Information for the Certification of Radio Apparatus 3 RSS-210: Issue 8 , December 2010 Low-power Licence-exempt Radiocommunication Devices (All Frequency Bands): Category I Equipment Test detailed items/section required by FCC rules and results are as below: No . Section in CFR 47 Section in RSS-GEN, RSS-210 Description Result 1 15.203 7.1.4 Antenna Requirement PA S S 2 15.247(b) A8.4 (2) Peak Output Power PASS 3 15.247(b) A8.4 (2) Average power PASS 4 15.247(a) A8.2 (a) 6dB Bandwidth PASS 5 15.247(a) A8.2 (a) 99% Bandwidth PASS 8 15.247(d) A8.5 Conducted Spurious Emission and Band Edge PA S S 9 15.247(d) A8.5 Restricted Frequency Bands PASS 10 15.207 7.2.4 Conducted Emission N/A 11 15.209 15.247(d) A8.5 Radiated Emission PASS 12 15.247(e) A8.2(b) Power spectral density (PSD) PASS 10 15.247(i). §1.1307&2.1093 RSS-102 RF exposure evaluation PASS The tests of Conducted Emission and Radiated Emission were performed according to the method of measurements prescribed in ANSI C63.4 2009. These RF tests were performed according to the method of measurements prescribed in KDB558074 D01 V02 10/04/2012. SZ13020021W03 Page 5 of 38 1.3. Facilities and Accreditations 1.3.1. Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at FL.1, Building A, FeiYang Science Park, Block 67, BaoAn District, Shenzhen, 518101 P. R. China. The test site is constructed in conformance with the requirements of ANSI C63.10 2009, ANSI C63.4 2009 and CISPR Publication 22; the FCC registration number is 695796. The IC registration number is 7183A-2. 1.3.2. Test Environment Conditions During the measurement, the environmental conditions were within the listed ranges: Tem…

Text truncated - open the document above for the full version.

Test Setup Photos 1. Conducted emission main’s port front view 2. Conducted emission main’s port side view 3. Radiated emission (9KHz-30MHz) 4. Radiated emission (30MHz-1GHz) 5. Radiated emission (above 1GHz) 6. Conducted emission antenna’s port