S7Y-MV1KKTS350-X

KTS350-X User Manual Date – April 2020 Navtech Radar Limited Home Farm, Ardington, Wantage, Oxfordshire, OX12 8PD, UK +44(0)1235 832419 [email protected] Page 2 of 12 1 Table of Contents 1 Table of Contents ........................................................................................................... 2 2 Introduction .................................................................................................................... 3 2.1 ClearWay™ ............................................................................................................ 3 2.2 Support ................................................................................................................... 3 2.3 Patent Information................................................................................................... 4 3 KTS350-X ...................................................................................................................... 4 3.1 Dimensions ............................................................................................................. 4 3.1.1 Mounting Holes ................................................................................................... 4 4 Installation ...................................................................................................................... 5 4.1 Essential Equipment ............................................................................................... 5 4.2 Connecting the Radar ............................................................................................. 5 4.2.1 Connect Power and Network ............................................................................... 6 4.2.2 Care Point ........................................................................................................... 6 4.3 Optimising the Radar Mount Angle ......................................................................... 7 5 Using the Vertex interface ............................................................................................ 10 5.1 To Access the Vertex Interface ............................................................................. 10 5.2 Changing the IP Address ...................................................................................... 12 Page 3 of 12 2 Introduction This purpose of this guide is to provide sufficient information to allow a KTS350-X radar to be physically installed, powered up and configured to correctly communicate over a network. This guide assumes that a suitably trained person has already performed a site survey and a suitable mounting location identified. The KTS350-X radar, together with the Navtech Radar software Witness, form the Navtech Radar ClearWay Automatic Incident Detection system. Service and Maintenance procedures are covered in a separate manual. 2.1 ClearWay™ The ClearWay system is an important component of a Smart Highways solution, providing accurate and reliable vehicle tracking and Automatic Incident Detection (AID) for roads, bridges and tunnels. The ‘Smart Highways’ concept, enables improved traffic flow and enhanced safety through the effective use of technology. Increasing safety on our motorways and reducing traffic congestion have become major goals for us at Navtech Radar. In the UK alone, more than £2 billion a year is lost due to traffic congestion, not to mention the negative effects on the environment and health. 2.2 Support Navtech Radar Ltd offer comprehensive support services both pre and post radar commissioning to ensure you get the best performance and support for your radar installation. Navtech Radar Ltd have a dedicated Customer Services Support Centre that can offer 1st and 2nd line technical support for both hardware and software queries. The centre is staffed by a highly skilled technical team who can advise and offer support with any technical questions both pre and post commissioning. In the event a fault cannot be diagnosed remotely, or a repair is required, the team can arrange for your radar to be returned to base for further diagnostic tests or repair. Navtech Radar Ltd also offer a number of support plan options during the lifetime of your radar, offering peace of mind for your installation. For further information on the support plan options or any technical questions please contact the Customer Services Support Centre on +44 (0) 1235 832419, or email at [email protected] Page 4 of 12 2.3 Patent Information GB Patent No.: GB 2 518 344 US Patent No.: 10 522893 3 KTS350-X 3.1 Dimensions Throughout this manual generic stock images of a Navtech Radar system are used. 3.1.1 Mounting Holes Page 5 of 12 4 Installation The KTS350-X can be mounted on a dedicated post or various other structures (e.g. walls, roofs, gantries) by use of brackets. For correct operation of the radar, Navtech recommend that any bracket should not move more than half degree in any direction whilst carrying the 12kg load of the radar under the required operating conditions (customer site specific). Ensure that the radar line of sight is not obscured by any existing infrastructure. To allow the radar to be installed in the optimum position relative to the road surface, the KTS350-X radar should be fitted to a mounting plate which allows the tilt to be adjusted (see below). The KTS350-X radar is fitted to the mounting plate using 4x M8 bolts in a 4” PCD pattern (standard CCTV mounting). The procedure for adjusting the tilt to optimise the radar performance is detailed in the section Levelling and optimising the radar position. The mounting plate provides a simple method to fine tune the incline of the radar. For each of the mounting holes, the bolt is fed from underneath and locked onto the mounting plate with a nut. Two more nuts are used below the radar base plate and another is used above so that the sensor can be positioned anywhere up or down the bolt thread, as necessary. An extra nut should then be added once th…

Text truncated - open the document above for the full version.

Registered in England No. 03699400 VAT Reg No. 742071067 Registered office: Home Farm, Ardington, Wantage, Oxfordshire, UK, OX12 8PD Navtech Radar Limited Home Farm, Ardington, Wantage, Oxfordshire, OX12 8PD, UK +44(0)1235 832419 [email protected] LETTER OF AGENCY 23rd April 2020 Element Materials Technology 100 Frobisher Business Park Malvern Worcestershire WR14 1BX UK To Whom It May Concern: We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application, is subject to denial of federal benefits, that includes FCC benefits. Thank you for your attention to this matter. Yours faithfully Navtech Radar Ltd Richard Poulton Hardware Team Leader

Registered in England No. 3699400 VAT Reg No. 742071067 Registered office : Home Farm, Ardington, Wantage, Oxfordshire, UK, OX12 8PD Navtech Radar Limited Home Farm, Ardington, Wantage, Oxforshire, OX12 8PD, UK +44(0)1235 832419 [email protected] Agent Authorization Letter 14 th January 2020 Element Materials Technology 100 Frobisher Business Park Malvern Worcestershire WR14 1BX UK To Whom It May Concern: We, the undersigned, hereby authorize Element Materials Technology to act on our behalf, as our agent, in the following matters related to the FCC and/or Industry Canada approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by Element Materials Technology within the scope of this authorization shall have the same affect as our own. This authorization shall expire 12 months from original date. Thank you for your attention to this matter. Yours faithfully Navtech Radar Ltd Richard Poulton Hardware Team Leader

Registered in England No. 3699400 VAT Reg No. 742071067 Registered office : Home Farm, Ardington, Wantage, Oxfordshire, UK, OX12 8PD Navtech Radar Limited Home Farm, Ardington, Wantage, Oxfordshire, OX12 8PD, UK +44(0)1235 832419 [email protected] To: Element Materials Technology Unit E, South Orbital Trading Park Hedon Road Hull HU9 1NJ Subject: Request for Short-term confidentiality FCC ID: S7Y-MV1K To whom it may concern, Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §0.457(d) and the importation rules in 47 CFR §0.459, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1):  User’s Manual  Test Set-up Photos  External Photos Justification: The unit is in the process of being released to the market as Navtech wish to restrict any competitive disadvantage by releasing images of the unit and installation details from the manual. The radar is a non-consumer device, serviced only by Navtech Radar Ltd or a designated trained and approved technician. Planned Release Date STC: 1 st July 2020 (notes 2, 3, 4, 5) Date: 7 th May 2020 Name and signature of applicant: Mr Richard Poulton Notes: 1) A document or type of document can only have ONE type of confidentiality!. 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.). 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Element does not remind you of this. 5) Request for extension or for release must be received by Element at least 7 days before date of actual marketing or before expiration of the STC period.

Page 1 of 3 MUTUAL NON-DISCLOSURE AGREEMENT THIS AGREEMENT is made on (the “Effective Date”). BETWEEN: (1) of and (2) Navtech Radar Limited whose registered office is Unit 8, Home Farm Close, Ardington, WANTAGE, OX12 8PD (hereinafter called ‘Navtech’). WHEREAS: (1) The parties wish to carry on confidential discussions and negotiations in relation to: (2) During such discussions and negotiations it may be necessary for any of the parties (the "Disclosing Party") to disclose Confidential Information (as defined below) to one of the other parties (the "Recipient"). (3) The parties wish to protect their respective Confidential Information from unauthorized disclosure or use and to define their mutual rights and obligations in respect of the Confidential Information. THE PARTIES AGREE AS FOLLOWS: 1. As used herein, "Confidential Information" shall mean any and all technical and non- technical information provided by either party to the other, including but not limited to patent and patent applications, proprietary information, ideas, techniques, sketches, drawings, works of authorship, models, inventions, data, databases, know-how, processes, apparatuses, equipment, algorithms, copyrights, software programs, software source documents, formulae, trade and business names, trade marks, service marks and designs related to the current, future, and proposed products and services of each of the parties, and including, without limitation, their respective information concerning research, experimental work, development, design details and specifications, engineering, financial information, procurement requirements, purchasing, manufacturing, customer lists, investors, employees, business and contractual relationships, business forecasts, business plans, sales and merchandising, marketing plans and information. 2. Each party agrees that at all times and notwithstanding any termination or expiration of this Agreement it will hold in strict confidence and not disclose to any third party Confidential Information of the other (except as approved in writing by the other party to this Agreement) and will use the Confidential Information for no purpose other than in relation to: (i) the business discussions between the parties and any on-going business relationship between the parties; and (ii) the setting up of a business plan for the envisioned operation. It is specifically understood and agreed by all the Parties that this business plan can be used for raising the necessary financial means to develop the operation envisioned by the Parties. 3. Each party shall only permit access to Confidential Information of the other party to those of its employees or authorized representatives having a need to know and who have signed confidentiality agreements or are otherwise bound by confidentiality obligations at least as restrictive as those contained herein. Page 2 of 3 4. Each party shall immediately notify the other upon discovery of any loss or unauthorized disclosure of the Confidential Information of the other party. 5. Each party's obligations under this Agreement with respect to any portion of the other party's Confidential Information shall terminate when the Recipient can document that the Confidential Information disclosed: (a) was in the public domain at the time it was communicated to the Recipient by the Disclosing Party; (b) entered the public domain subsequent to the time it was communicated to the Recipient by the Disclosing Party through no fault of the Recipient; (c) was in the Recipient's possession free of any obligation of confidence at the time it was communicated to the Recipient by the Disclosing Party; (d) was rightfully communicated to the Recipient free of any obligation of confidence subsequent to the time it was communicated to the Recipient by the Disclosing Party; (e) was developed by employees or agents of the Recipient independently of and without reference to any information communicated to the Recipient by the Disclosing Party; (f) was communicated to the Recipient by an unaffiliated third party free of any obligation of confidence and (g) the communication was in response to a valid order by a court or other governmental or regulatory body or was otherwise required by law. 6. Unless an extension is agreed and confirmed in writing by all parties, this agreement will expire 2 years after the Effective Date of this agreement. 7. Upon termination or expiration of the Agreement, or upon written request of the other party, each party shall promptly return to the other all documents and other tangible materials representing the other's Confidential Information and all copies thereof. 8. The parties recognize and agree that nothing contained in this Agreement shall be construed as granting any property rights, by license or otherwise, to any Confidential Information of the other party disclosed pursuant to this Agreement, or to any invention or any patent, copyright, trade mark, or other intellectual property right that has issued or that may issue, based on such Confidential Information. 9. No party shall make, have made, use or sell for any purpose any product or other item using, incorporating or derived from any Confidential Information of the other party. 10. Confidential Information shall not be reproduced in any form except as required to accomplish the intent of this Agreement. The Recipient's obligations under this Agreement shall survive termination of the Agreement between the parties and shall be binding upon the Recipient's heirs, successors and assigns. 11. This Agreement shall be governed by and construed in accordance with the laws of England and the parties hereby submit to the non-exclusive jurisdiction of the English Courts. 12. Each party acknowledges that its breach of the Agreement will cause irreparable damage and hereby agrees that the other party shall be entitled to seek injunctive relief under this Agreement, as well as such further relief as may be granted b…

Text truncated - open the document above for the full version.

Registered in England No. 3699400 VAT Reg No. 742071067 Registered office : Home Farm, Ardington, Wantage, Oxfordshire, UK, OX12 8PD Request for Confidentiality 22 nd April 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, Maryland 21046 Subject: Request for long-term confidentiality FCC ID: S7Y-MV1K To Whom It May Concern: We hereby respectfully request that under the provision of 47 CFR 0.459 and 0.457(d) the documents listed below and attached with this application for certification be provided with confidential status. • Bill Of Materials • Schematics • PCB Artwork • Operation Description • Block Diagram • Internal Photographs The application contains technical information which Navtech Radar Ltd deems to be trade secrets and propriety. If made public, the information might be used to the disadvantage of the applicant in the market place. Navtech Radar Ltd have request that the internal phots be held confidential for the following reasons: • The internal circuit boards and components are not accessible to users without dismantling the unit. • The unit is not accessible to the public as the installation locations are within secure locations such as within airport perimeters, on Highways and are mounted on posts typically 4-6m from ground level. • The units are not field serviceable and must be returned to a service centre for operations that require the enclosure to be opened. • Purchasers and professional installers shall be subject to an appropriate NDA. Any exhibit / information for which we have requested confidentiality, but which may not be accorded such treatment by the FCC, should be returned to us. The documents listed above contain trade secrets that are treated as confidential by us. Substantial competitive harm to us could result should they be made available to the public. Thank you for your attention to this matter. Yours faithfully Navtech Radar Ltd Mr Richard Poulton Navtech Radar Limited Home Farm, Ardington, Wantage, Oxfordshire, OX12 8PD, UK +44(0)1235 832419 [email protected]

Registered in England No. 03699400 VAT Reg No. 742071067 Registered office: Home Farm, Ardington, Wantage, Oxfordshire, UK, OX12 8PD Navtech Radar Limited Home Farm, Ardington, Wantage, Oxfordshire, OX12 8PD, UK +44(0)1235 832419 [email protected] 23 rd April 2020 Subject: FCC Application Request FCC ID: S7Y-MV1K FRN: 0022396238 To Whom It May Concern, Navtech Radar Ltd are seeking FCC approval for the equipment identified above as an original certification under Part 90, Subpart F. The equipment is a fixed infrastructure ground surveillance radar for applications including but not limited to Highways monitoring, wide area surveillance and logistical operations such as yard management. The application contains two separate reports from different test labs. The operating conditions for the equipment were identical in each test. The reason for the separate reports is purely due to the capability of the labs in terms of total frequency covered. Yours faithfully, Richard Poulton Hardware Team Leader

Page 1 of 4 S7Y-MV1K External Images Page 2 of 4 Page 3 of 4 Page 4 of 4

Registered in England No. 03699400 VAT Reg No. 742071067 Registered office: Home Farm, Ardington, Wantage, Oxfordshire, UK, OX12 8PD Navtech Radar Limited Home Farm, Ardington, Wantage, Oxfordshire, OX12 8PD, UK +44(0)1235 832419 [email protected] FCC ID: S7Y-MV1K Example Label for the product:

S EIRP R R EIRP S

Page 1 of 29 File Name: Element Materials Technology.11750-1 Issue 02 QMF21J - Issue 05 - RNE Issue 03; FCC Part 90I Radio Test Report Element Materials Technology KTS350-X 47 CFR Part 90I Effective Date 1st October 2019  47CFR part 2J 2018 TNB: Licensed Non-Broadcast Station Transmitter Test Date: 11th March 2020 Report Number: 03-11750-1-20 Issue 02 Supersedes Report Number: 03-11750-1-20 Issue 01 R.N. Electronics Ltd. Arnolds Court Arnolds Farm Lane Mountnessing Essex CM13 1UT U.K. www.RNelectronics.com Telephone: +44 (0) 1277 352219 Email: [email protected] This report is not to be reproduced by any means except in full and in any case not without the written approval of R.N. Electronics Ltd. ©2020 RN ELECTRONICS LIMITED REPORT NUMBER: 03-11750-1-20 Issue 02 ALL RIGHTS RESERVED Page 2 of 29 File Name: Element Materials Technology.11750-1 Issue 02 QMF21J - Issue 05 - RNE Issue 03; FCC Part 90I Arnolds Court, Arnolds Farm Lane, Mountnessing, Brentwood Essex, CM13 1UT Certificate of Test 11750-1 The equipment noted below has been partially tested by R.N. Electronics Limited and, where appropriate, conforms to the relevant subpart of FCC Part 90I. This is a certificate of test only and should not be confused with an equipment authorisation. Other standards may also apply. Equipment: KTS350-X Model Number: KTS350-X Unique Serial Number: 02017 Applicant: Element Materials Technology Unit E, South Orbital Trading Park, Hedon Road Hull, East Yorkshire, HU9 1NJ Proposed FCC ID S7Y-MV1K Full measurement results are detailed in Report Number: 03-11750-1-20 Issue 02 Test Standards: 47 CFR Part 90I Effective Date 1st October 2019  47CFR part 2J 2018 TNB: Licensed Non-Broadcast Station Transmitter NOTE: Certain tests were not performed based upon manufacturer's declarations. Certain other requirements are subject to manufacturer declaration only and have not been tested/verified. For details refer to section 3 of this report. DEVIATIONS: The following tests have not been performed at the request of Element Materials Technology:- Adjacent channel power, Conducted emissions, Conducted power, Emission mask, Frequency stability, Modulation frequency response, Modulation limiting, Occupied bandwidth, Transient frequency behaviour. Results pertaining to these tests can be found in Element Materials Technology Ltd report number TRA-041847-45-00. This certificate relates only to the unit tested as identified by a unique serial number and in the condition at the time it was tested. It does not relate to any other similar equipment and performance of the product before or after the test cannot be guaranteed. Whilst every effort is made to assure quality of testing, type tests are not exhaustive and although no non-conformances may be found, this doesn't exclude the possibility of unit not meeting the intentions of the standard or the requirements of the Federal Regulations, particularly under different conditions to those during testing. Any compliance statements are made reliant on (a) the application of the product and use of the assigned band being acceptable to the FCC and (b) the modes of operation as instructed to us by the Customer based on their specific knowledge of the application and functionality of the EUT. Statements of compliance, where measurements were made, do not include the measurement uncertainty. The measurement uncertainty, where stated, is the expanded uncertainty based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95%. Date Of Test: 11th March 2020 Test Engineer: Approved By: Technical Director Customer Representative: ©2020 RN ELECTRONICS LIMITED REPORT NUMBER: 03-11750-1-20 Issue 02 ALL RIGHTS RESERVED Page 3 of 29 File Name: Element Materials Technology.11750-1 Issue 02 QMF21J - Issue 05 - RNE Issue 03; FCC Part 90I 0 Revision History Issue Number Revision History Page Reference(s) 01 First Issue - 02 Corrected serial number from 2017 to 02017. Corrected Emission mask reference from 90.210(b) to 90.210(c). Added reference to applicants test report for all tests not performed by RN Electronics Ltd. All photographs obscured at request of applicant. 2 & 5 8 2, 8, 9 &11 19-24 ©2020 RN ELECTRONICS LIMITED REPORT NUMBER: 03-11750-1-20 Issue 02 ALL RIGHTS RESERVED Page 4 of 29 File Name: Element Materials Technology.11750-1 Issue 02 QMF21J - Issue 05 - RNE Issue 03; FCC Part 90I 1 Contents 0Revision History .............................................................................................................................................. 3 1 Contents .......................................................................................................................................................... 4 2 Equipment under test (EUT) ........................................................................................................................... 5 2.1 Equipment specification ......................................................................................................................... 5 2.3 Functional description ............................................................................................................................ 6 2.4 Modes of operation ................................................................................................................................. 6 2.5 Emissions configuration ......................................................................................................................... 7 3 Summary of test results .................................................................................................................................. 8 4 Specifications .................................................................................................................................................. 9 4.1 Relevant standards ........................................................................................................…

Text truncated - open the document above for the full version.

RF922 5.0 Report on the Radio Testing For Navtech Radar Ltd on KTS350-X Report no. TRA-041847-45-00B 2020-06-12 RF922 5.0 REPORT ON THE RADIO TESTING OF A Navtech Radar Ltd KTS350-X WITH RESPECT TO SPECIFICATION FCC 47 CFR Part 90 Subpart F TEST DATE: 2020-03-02 to 2020-04-01 Written by: David Garvey Radio Test Engineer Approved by: John Charters Lab Manager Date: 2020-06-12 Disclaimers: [1] THIS DOCUMENT MAY BE REPRODUCED ONLY IN ITS ENTIRETY AND WITHOUT CHANGE [2] THE RESULTS CONTAINED IN THIS DOCUMENT RELATE ONLY TO THE ITEM(S) TESTED Report Number: TRA-041847-45-00B Issue: B Report Number: TRA-041847-45-00B RF922 5.0 Page 3 of 41 1 Revision Record Issue Number Issue Date Revision History A 2020-04-08 Original B 2020-06-12 Updated after certification checking Report Number: TRA-041847-45-00B RF922 5.0 Page 4 of 41 2 Summary TEST REPORT NUMBER: TRA-041847-45-00B WORKS ORDER NUMBER: TRA-041847-02 PURPOSE OF TEST: USA: Testing of radio frequency equipment per the relevant authorization procedure of chapter 47 of CFR (code of federal regulations) Part 2, subpart J. TEST SPECIFICATION: FCC 47 CFR Part 90 Subpart F EQUIPMENT UNDER TEST (EUT): KTS350-X FCC IDENTIFIER: S7Y-MV1K EUT SERIAL NUMBER: 2017 MANUFACTURER/AGENT: Navtech Radar Ltd ADDRESS: 16 Home Farm Ardington Wantage Oxfordshire OX12 8PD United Kingdom CLIENT CONTACT: Rick Poulton  01235 433592  [email protected] ORDER NUMBER: 20108 TEST DATE: 2020-03-02 to 2020-04-01 TESTED BY: David Garvey Element Report Number: TRA-041847-45-00B RF922 5.0 Page 5 of 41 2.1 Test Summary Test Method and Description Requirement Clause Applicable to this equipment Result / Note 47CFR90 Output power 2.1046 / §90.205 Power and antenna height limits. Pass Occupied bandwidth 2.1049 / §90.209 Bandwidth limitations. Pass Spurious emissions at antenna terminal 2.1051 / §90.207 Types of emissions. N/A Note 3 Field strength of spurious radiation 2.1053 / §90.207 Types of emissions. Pass Note 1 Note 2 Frequency stability 2.1055 / §90.213 Frequency stability. Pass AC power line conducted emissions 15.207 Pass Notes: Note 1: Emission only performed to 110 GHz. The radiated spurious emissions above 110 GHz was performed by RN Electronics. The report number by RN Electronics is 03-11750-1-20. Note 2: The following product was tested against the 15.209 limits as these are stricter than the 13 dBm limit as per Part 90. Note 3: The EUT was purely radiated sample. The results contained in this report relate only to the items tested, in the condition at time of test, and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. The apparatus was set up and exercised using the configurations, modes of operation and arrangements defined in this report only. Any modifications made are identified in Section 8 of this report. Particular operating modes, apparatus monitoring methods and performance criteria required by the standards tested to have been performed except where identified in Section 5.2 of this test report (Deviations from Test Standards). Report Number: TRA-041847-45-00B RF922 5.0 Page 6 of 41 3 Contents 1 Revision Record ................................................................................................................................ 3 2 Summary ........................................................................................................................................... 4 2.1 Test Summary ........................................................................................................................... 5 3 Contents ............................................................................................................................................ 6 4 Introduction ....................................................................................................................................... 8 5 Test Specifications ............................................................................................................................ 9 5.1 Normative References .............................................................................................................. 9 5.2 Deviations from Test Standards ................................................................................................ 9 6 Glossary of Terms ........................................................................................................................... 10 7 Equipment Under Test .................................................................................................................... 11 7.1 EUT Identification .................................................................................................................... 11 7.2 System Equipment ...…

Text truncated - open the document above for the full version.