S8W-W01AWhistle Dog Activity Monitor

Whistle Activity Monitor – BT Pairing & Wi-­‐Fi Setup Explanation Released: September 6, 2013 1. The Whistle iOS app when first running will prompt the user to initiate pairing on device by holding button 4 seconds. 2. After clicking “pair” the Whistle iOS will display the iOS in-­‐app pairing dialogue which shows a list of available Bluetooth devices. This will show the Whistle device and the user will need to select it. 3. Once the device is paired the iOS app will request the device to query the available Wi-­‐Fi networks. The device will then disconnect Bluetooth, turn off Bluetooth, turn on Wi-­‐Fi, scan for Wi-­‐Fi networks, turn off Wi-­‐Fi, turn on Bluetooth, reconnect to the phone, sends the results of the Wi-­‐Fi scan to the iOS app. NOTE: throughout this process it is ensured that only one radio operates at a time. 4. Once the user selects the Wi-­‐Fi network the user will be prompted for the password. 5. Once the user enters the password the iOS app will send the network name and password to the device. The device will then disconnect Bluetooth, turn off Bluetooth, turn on Wi-­‐Fi, attempt to connect to the provided Wi-­‐Fi network, store the result of this attempt, turn off Wi-­‐Fi, turn on Bluetooth, reconnect to the phone, sends the results of the Wi-­‐Fi connection attempt to the iOS app. NOTE: throughout this process it is ensured that only one radio operates at a time. 6. If the device successfully connected to the WiFi network the app will then display a lists of the configured / saved networks on the device.

Whistle Info FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This portable transmitter with its antenna has shown compliance with FCC’s SAR limits for general population / uncontrolled exposure. The maximum listed SAR level is: • 0.61 W/kg (body). The antenna used for this device must not be co-located or operating in conjunction with any other antenna or transmitter. Canadian Compliance Statement: This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme aux normes CNR exemptes de licence d'Industrie Canada. Le fonctionnement de ce dispositif est autorisé sous réserve des deux conditions suivantes: 1. Ce dispositif ne doit pas produire de brouillage et 2. L'utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif . Whistle Product Terms of Sale IMPORTANT: YOU MUST READ AND AGREE TO THESE WHISTLE PRODUCT TERMS OF SALE (“AGREEMENT”) BEFORE OPENING OR USING THE WHISTLE ACTIVITY MONITOR (THE “PRODUCT”) IN ANY WAY. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, YOU HAVE NO RIGHT TO USE THE PRODUCT, AND YOU MUST, WITHIN THIRTY (30) DAYS OF YOUR RECEIPT OF THE PRODUCT, (A) CONTACT WHISTLE LABS, INC. (“WHISTLE,” “WE,” “US,” “OUR”) AT [email protected] AND (B) ARRANGE FOR THE RETURN OF AND REFUND FOR THIS PRODUCT DIRECTLY FROM THE SOURCE FROM WHICH YOU PURCHASED IT. WHISTLE WILL REASONABLY ASSIST YOU WITH RETURNS AND REFUNDS. IF YOU WISH TO RETURN THIS PRODUCT BECAUSE YOU DO NOT AGREE WITH ALL OF THE TERMS AND CONDITIONS OF THIS AGREEMENT, SUCH RETURNS WILL ONLY BE ACCEPTED BY THE PURCHASE SOURCE IF THE PRODUCT IS IN ITS ORIGINAL PACKAGING. This Agreement shall govern the sale and license to you (“User,” “you,” “your”) of the Product by Whistle. The Product is designed to be used in connection with the Service(s) (as that term is defined in the Terms of Use, available at http://www.whistle.com/terms-of-service) offered by Whistle. This Agreement shall apply only to the Product itself, and not the Services. Your use of the Services shall be governed by the Terms of Use. You understand and agree that references herein to the “Product” shall mean all parts and components of the Product (including without limitation the Software and any documentation provided by Whistle in connection with the Product). Product Use You may only use the Product for User’s own personal, non-commercial use. As a condition to using the Product, User must sign up for an account with Whistle by downloading the Application and, if applicable, pay any fees associated with such account (as further explained in the Terms of Use). User understands and acknowledges that the Product may not function properly if User does not keep his or her Whistle account current and up-to-date, and pay any fees due, if applicable. Except as expressly set forth herein, all fees paid hereunder and/or with respect to the Product are nonrefundable. License Subject to the terms and conditions of this Agreement and the Terms of Use, Whistle hereby grants a non-exclusive, non-sublicenseable, non-transferrable license to User to use the object code version of any software incorporated or embedded into the Product (“Software”), only for User’s personal, non-commercial purposes in conjunction with User’s use of the Product and only in and as part of the specific hardware into which it is incorporated or designated by Whistle. Except for the license granted under this Section, Whistle and its licensors shall retain all rights, title, and interest in and to the Software and all copies thereof. Notwithstanding anything herein or in the Terms of Use to the contrary, Software provided as part of the Product is licensed, not sold. This license shall commence on the date a User first uses the Product and will remain in eect in perpetuity, unless earlier terminated in accordance with the provisions of this Section. Whistle may terminate this license immediately upon notice to User, for any reason or for no reason. Upon such termination, User shall have no further right to use the Software for any reason and shall cease use of the Software immediately. The following sections of this Agreement will survive any termination of User’s licens…

Text truncated - open the document above for the full version.

251 Rhode Island Street Suite 201 San Francisco, CA 94103 1 Whistle Confirmation of Wi-Fi Operating Channels To Whom It May Concern: I would like to confirm on behalf of Whistle Labs, Inc. that the Whistle Activity Monitor (FCC ID S8W-W01A) when shipped to North America will only operate in Wi-Fi channels 1 – 11. Similarly Channels 12, 13 and 14 will be disabled. This will be accomplished by ensuring all devices manufactured for and shipped to North America contain software that explicitly configures the Atheros AR4100P (Wi-Fi chip) per it’s proprietary command set to only operate on Wi-Fi channels 1 – 11. Regards, David Isbister David Isbister Director of Hardware, Whistle 415-609-9577 // [email protected]

251 Rhode Island Suite 211 San Francisco CA 94103 Authority to Act as Agent Date: August 29, 2013 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: Thomas T. Smith, Ryan Urness and Amanda Hauck of LS Research, LLC is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. The term of this Agency Agreement shall start on the above date of this Agreement and shall continue in force until one (1) year thereafter. Thank you, By: _____________________ David Isbister (Signature) (Print name) Title: Director of Hardware On behalf of: Whistle Labs, Inc. Telephone: 415-692-0200

251 Rhode Island Suite 211 San Francisco CA 94103 Request for Confidentiality Date: June 21 st , 2013 Subject: Confidentiality Request for: FCC ID: S8W-W01A IC ID: 10959A-W01A Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality RequestedExhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent User’s Manual Whistle Labs, Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: ____________________ David Isbister, Director of Hardware (Signature) (Print name)

EXTERNAL PHOTOS Company Name Whistle Labs, Inc. Model # W01A FCC ID # S8W‐W01A IC # 10959A‐W01A Page 1 of 2 Device with Charger Close up of device and charger connection EXTERNAL PHOTOS Company Name Whistle Labs, Inc. Model # W01A FCC ID # S8W‐W01A IC # 10959A‐W01A Page 2 of 2

FCC marks Etched FCC marks Etched Scale 1/1 WHISTLE - FCC MARKING BACK VIEW OF THE PRODUCT - LOCATION PLACEMENT MARKING - DIMENSIONS newdealdesign © 2011 condential 34.62 mm 34.14 mm

INTERNAL PHOTOS Company Name Whistle Labs, Inc Model # W01A FCC ID # S8W‐W01A IC # 10959A‐W01A Page 1 of 3 Internal Photos of Bluetooth board INTERNAL PHOTOS Company Name Whistle Labs, Inc Model # W01A FCC ID # S8W‐W01A IC # 10959A‐W01A Page 2 of 3 Internal Photos of WiFi board INTERNAL PHOTOS Company Name Whistle Labs, Inc Model # W01A FCC ID # S8W‐W01A IC # 10959A‐W01A Page 3 of 3 Close up of antenna

802 N. Twin Oaks Valley Road, Suite 105 • San Marcos, CA 92069 • U.S.A. TEL (760) 471-2100 • FAX (760) 471-2121 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION Whistle Labs, Inc. Dates of Test: August 20, 2013 251 Rhode Island St., Suite 211 Test Report Number: SAR.20130807 San Francisco, CA 94103 This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1999 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2003, OET Bulletin 65 Supp. C, RSS-102 and Safety Code 6 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application has been denied FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Certificate # 2387.01 FCC ID: S8W-W01A IC Certificate: 10959A-W01A Model(s): W01A Contains WLAN Module: Qualcomm Atheros Model AR4100P; FCC ID: PPD-AR4100; IC: 4104A-AR4100 Test Sample: Engineering Unit Same as Production Serial Number: E07C62000872 Equipment Type: Wireless Dog Activity Monitor Classification: Portable Transmitter Next to Body TX Frequency Range: 2412 – 2462 MHz Frequency Tolerance: ± 2.5 ppm Maximum RF Output: 2450 MHz – 17.1 dB Conducted Signal Modulation: DSSS, OFDM Antenna Type: Internal, PIFA Antenna Application Type: Certification FCC Rule Parts: Part 2, 15C KDB Test Methodology: KDB 447498 D01 v05 Industry Canada: RSS-1 02, Safety Code 6 Maximum SAR Value: 0.61 W/kg Reported Separation Distance: 0 mm © 2013 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Report Number: SAR.20130807 Table of Contents 1. Introduction ......................................................................................................................... 3 SAR Definition [5] ................................................................................................................... 4 2. SAR Measurement Setup .................................................................................................... 5 Robotic System ...................................................................................................................... 5 System Hardware ................................................................................................................... 5 System Description ................................................................................................................ 5 E-Field Probe ......................................................................................................................... 6 3. Robot Specifications............................................................................................................ 8 4. Probe and Dipole Calibration ............................................................................................... 9 5. Phantom & Simulating Tissue Specifications ..................................................................... 10 Head & Body Simulating Mixture Characterization ................................................................10 6. ANSI/IEEE C95.1 – 1992 RF Exposure Limits [2] .............................................................. 11 Uncontrolled Environment .....................................................................................................11 Controlled Environment .........................................................................................................11 7. Measurement Uncertainty ................................................................................................. 12 8. System Validation ............................................................................................................. 13 Tissue Verification .................................................................................................................13 Test System Verification ........................................................................................................13 9. SAR Test Data Summary .................................................................................................. 14 Procedures Used To Establish Test Signal ...........................................................................14 Device Test Condition ...........................................................................................................14 SAR Data Summary – 2450 MHz Body 802.11b and 802.11g...............................................16 10. Test Equipment List ....................................................................................................... 17 11. Conclusion .................................................................................................................... 18 12. References .................................................................................................................... 19 Appendix A – System Validation Plots and Data ....................................................................... 20 Appendix B – SAR Test Data Plots ........................................................................................... 23 Appendix C – SAR Test Setup Photos ...................................................................................... 26 Appendix D – Probe Calibration Data Sheets ............................................................................ 31 Appendix E – Dipole Calibration Data Sheets ........................................................................... 42 Appendix F – Phantom Calibration…

Text truncated - open the document above for the full version.

September 9, 2013 RE: ATCB014564 FCC ID: S8W‐W01A & IC: 10959A‐W01A for Whistle Labs, Inc. Response for TCB comments: 5(d): The spurious radiated emissions from the Bluetooth Low Energy mode of the device were not provided in the original test report for a series of related reasons. The Bluetooth Low Energy mode has a lower output power when compared to Classic Bluetooth and the EDR modes. Radiated emissions were performed on the Classic Bluetooth mode, as can be found in the FHSS report related to this EUT. Bluetooth Classic and Low Energy modes demonstrate similar modulations, and Classic mode operates at a higher output power, justifying no further radiated emissions testing in Low Energy mode.

W66 N220 Commerce Court ● Cedarburg, WI 53012 ● USA Phone: 262.375.4400 ● Fax: 262.375.4248 www.lsr.com TEST REPORT # 313049-A LSR Job #: C-1677 Compliance Testing of: Whistle Dog Monitor Test Date(s): July 19-31, August 1-14, 2013 Prepared For: Whistle 251 Rhode Island St Suite 211 San Francisco, CA 94103 In accordance with: Federal Communications Commission (FCC) Part 15, Subpart C, Section 15.247 Industry Canada (IC) RSS 210 Annex 8 Digital Modulation Transmitters (DTS) Operating in the Frequency Band 2400 MHz – 2483.5 MHz This Test Report is issued under the Authority of: Signature: Date: Test Report Reviewed by: Ryan M. Urness, Quality & Operations Manager Signature: Date: 8-27-13 Tested by: Peter Feilen, EMC Engineer Signature: Date: 8-21-13 This Test Report may not be reproduced, except in full, without written approval of LS Research, LLC. Prepared For: Whistle EUT: Whistle Dog Monitor LS Research, LLC Report # 313049-A Model #: W01A LSR Job #:C-1677 Serial #: Engineering Sample Page 2 of 63 Contents EXHIBIT 1. INTRODUCTION .......................................................................................................... 4 1.1 Scope .................................................................................................................................. 4 1.2 Normative References ........................................................................................................ 4 1.3 LS Research, LLC Test Facility ......................................................................................... 5 1.4 Location of Testing ............................................................................................................. 5 1.5 Test Equipment Utilized ..................................................................................................... 5 EXHIBIT 2. PERFORMANCE ASSESSMENT ............................................................................... 6 2.1 Client Information ............................................................................................................... 6 2.2 Equipment Under Test (EUT) Information ......................................................................... 6 2.3 Associated Antenna Description ......................................................................................... 6 2.4 EUT’s Technical Specifications ......................................................................................... 7 2.5 Product Description ............................................................................................................ 8 EXHIBIT 3. EUT OPERATING CONDITIONS & CONFIGURATIONS DURING TESTS ..... 9 3.1 Climate Test Conditions ..................................................................................................... 9 3.2 Applicability & Summary of EMC Emission Test Results ................................................ 9 3.3 Modifications Incorporated In the EUT For Compliance Purposes ................................... 9 3.4 Deviations & Exclusions From Test Specifications ........................................................... 9 EXHIBIT 4. DECLARATION OF CONFORMITY ..................................................................... 10 EXHIBIT 5. RADIATED EMISSIONS TEST .............................................................................. 11 5.1 Test Setup ......................................................................................................................... 11 5.2 Test Procedure .................................................................................................................. 11 5.3 Test Equipment Utilized ................................................................................................... 12 5.4 Test Results ........................................................................................................................ 12 5.5 Calculation of Radiated Emissions Limits ....................................................................... 13 5.6 Radiated Emissions Test Data Chart ................................................................................. 14 5.7 Screen Captures - Radiated Emissions Test ..................................................................... 16 5.9 Receive Mode Testing ...................................................................................................... 19 EXHIBIT 6. OCCUPIED BANDWIDTH: ..................................................................................... 22 6.1 Limits ................................................................................................................................ 22 6.2 Method of Measurements ................................................................................................. 22 6.3 Test Equipment List.......................................................................................................... 22 6.4 Test Results ........................................................................................................................ 22 6.5 Test Data ............................................................................................................................. 22 Prepared For: Whistle EUT: Whistle Dog Monitor LS Research, LLC Report # 313049-A Model #: W01A LSR Job #:C-1677 Serial #: Engineering Sample Page 3 of 63 EXHIBIT 7 BAND-EDGE MEASUREMENTS................................................................................ 31 7.1 Limits ................................................................................................................................... 31 7.2 Method of Measurements ................................................................................................. 31 7.3 Test Equipment List.......................................................................................................... 31 7.4 Test Results ..........................................................................................................…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOS Company Name Whistle Labs, Inc. Model # W01A FCC ID # S8W‐W01A IC # 10959A‐W01A Page 1 of 3 TEST SETUP PHOTOS Company Name Whistle Labs, Inc. Model # W01A FCC ID # S8W‐W01A IC # 10959A‐W01A Page 2 of 3 TEST SETUP PHOTOS Company Name Whistle Labs, Inc. Model # W01A FCC ID # S8W‐W01A IC # 10959A‐W01A Page 3 of 3