S94-PA0755CTablet MID

1 Attention: This handbook contains important security measures and the correct use of the product information, in order to avoid accidents. Please make sure to reading the manual carefully before use the device.
Please don’t be in high temperature, moisture or very dust place
Please don’t be in high temperature, especially in summer don't put the device in the car when Windows closed.
Avoid fall or Violent collision of the device, don’t make the TFT display screen were violent tremor, This could cause TFT display screen abnormal or damage.
Please choose the appropriate volume, Use headphones should not be too big volume, If feel tinnitus, Lower the volume or stop using it
please charge In the following condition, A、 The battery power ICONS shows have no power B、 The system automatically shut off, startup after power off soon C、 Operation buttons no response D、 The machine that the top right corner show red icons
When the device in the format or ongoing upload and download file, please don't suddenly disconnect, This could cause application error.
For those who because of damage to the product, repair, or other causes of erased the memory, The company shall not be liable for any responsibility, please follow the user manual for the standardized operation to use the device.
Don’t disassemble the product, don’t use alcohol、Thinner or benzene to scrubbing products
Don't use the device one of the place of prohibit to use electronic equipment in regional (such as the plane)
Please don't using the Tablet PC when you in driving or walking down the 2 street,
USB just only be used for data transmission The company reserves the right to improve product, products specification and design have any change, The information is subject to changes without prior notice. (This tablet is no waterproof function) 【Remark】All pictures in this manual is just for your reference. products specification and design have any change, The information is subject to changes without prior notice. 3 1. Appearance and button: 1.1 Touch panel 7” Capacitive touch panel: In the Operation, to click, dragging on the touch 4 panel 1.2 POWER startup: Long Press and hold the power button, the system will enter the main interface shutdown: In the main menu interface, Press the power button about 5 second to shutdown, The system can hint "power off" option, Click ”ok”. You can safely shut down. Lock screen: Short press Power button to lock screen or unlock screen. Remark 1.When power is empty, system will shut down automatically. 2. Illegal turn off the device, restart will scan and restore the disk, it may take longer time to enter into system 1.3 Home Short Press Home button will return the last interface; long Press Home button will return the main interface 1.4 Volume +, Volume- The buttons on top Volume +, Volume-achieve changes in the volume. 1.5 earphone jack 3.5 mm standard earphone jack 1.6 TF card TF-CARD slot: external T-FLASH card 1.7 Micro USB Micro USB jack: you can use it to connect the computer for data transmission, charging and external connection USB flash drive 2. First use 2.1 Battery management and charge Before first use, please set the device's battery is fully charged Just need to connect the adaptor or USB interface, then you can charge 5 The first two times charging please keep about 6 hours, after that you just need 4 hours to charge. 【Remark】: This tablet using Built-in type polymer battery, Charge must be to choose standard adaptor (Input: AC110~240V 50/60Hz Max：180MA.. Output: DC5.0~5.5V/1.5A), this device without supply DC charging, USB interface can charge, Choose USB interface to charger During the charging, the battery icon will scroll When finished charging, battery icon will become green and stop rolling In order to prolong the service life of the machine, suggest use out battery power before charge it 【Remark】: 1. If you long time doesn’t to use this Tablet, in order to avoid power consumption caused damage, please charge/play the battery once a month. 2、After low battery shut down, connect DC adaptor, device will remind low battery, charging, need to wait some time until the battery is enough power to enter into main menu. 3. Device charging should be in standby status for reach normal charging time. Because with device and screen consumption, it may cause longer charging time. 6 2.2 Connection with PC Use USB cable to connect device to PC, device will pop up the USB connection window, click Turn on USB storage to connect to PC Into the load mode, you can copy; delete the file on the device and the file on the memory card. 7 3. Equipment operation interface 3.1 Unlock Interface After starting up, the Locking interface will be shown firstly, just as the following: It is only available to conduct operation after unlocking. Unlocking method: touch the right Lock icon by hands, and drag it next to a lock at the right, then release hands. The system will be unlocked, and enter the main interface. If drag it to the left, the system will enter the Camera mode. 3.2 Main interface describe The main interface of the handheld tablet includes two modes: the small tools on the desktop mode and the icons of application programs mode, both of which can be switched between each other via the button at the top right corner. The mode of small tools on the desktop is shown as follows: 8 Tap button on the shortcut bar to enter the interface of icon modes for application programs, which is shown as follows: 9 Tap button to enter the desktop interface. 3.3 Shortcut Mode Under the interface of the mode of small tools on the desktop, after pressing Menu key, the Shortcut menu will popup at the bottom of the screen, shown as follows: 10 3.4 Usage of Small Tools on Desktop Users can add, delete or install the small tools on the desktop, as well as add or delete icons of application programs or adjust the positions of icons; the icons can be dragged within the working zone, or between the working zo…

Text truncated - open the document above for the full version.

Date:2013-3-26 FCC ID: S94-PA0755C We hereby declare that our device with the FCC ID above does not initiate and it can not be configured to initiate any transmission on any non-US frequencies or unauthorized frequencies. This includes probes, beacons, and ad-hoc mode transmissions. Our operation is limited to the following frequencies and modes: 802.11b Channel 1 (2412MHz) – Channel 11 (2462MHz) 802.11g Channel 1 (2412MHz) – Channel 11 (2462MHz) 802.11n (20MHz) Channel 1 (2412MHz) – Channel 11 (2462MHz) 802.11n (40MHz) Channel 3 (2422MHz) – Channel 9 (2452MHz) Name Sandy Boukai Title Signature

DATE: 2013/3/28 FCC DECLARATION OF CONFORMITY (DoC) Trade Name(s):iB Sleek Model Number(s):PA0755C Our device above has been tested and found to be compliant with the FCC Part 15 Class B limits as a computer peripheral. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Details of test lab and documentation Test Lab Name: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch FCC Test Site Accreditation Number (as seen on FCC website): TW1050 Test report number and issue date: FD130108C35 R1 JAN. 25, 2013 Name Sandy Boukai T itle Signature

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 3 Report Version 1 Reference No.: 130226N001 PHOTOGRAPHS OF THE EUT Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 3 Report Version 1 Reference No.: 130226N001 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 3 of 3 Report Version 1 Reference No.: 130226N001

FCC ID: S94-PA0755C This device compl ies with Part 15 of the FCC Rul es. Operation is subject to the following two conditions : (1) thi s device may not cause harmful int erference, and (2) thi s device must accept any interference received, including int erference that may cause undesired operation. Size:85*30MM

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 of 3 Report Version 1 Reference No.: 130226N001 PHOTOGRAPHS OF THE EUT Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 of 3 Report Version 1 Reference No.: 130226N001 Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel.: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 3 of 3 Report Version 1 Reference No.: 130226N001 ANT

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] No SAR justification for FCC ID : S94-PA0755C Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1‐g and 10‐g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune‐up tolerance, mW)/(min. test separation distance, mm)] ∙[√f(GHz)] ≤ 3.0 for 1‐g SAR and ≤ 7.5 for 10‐g extremity SAR,16 where ¾ f(GHz) is the RF channel transmit frequency in GHz ¾ Power and distance are rounded to the nearest mW and mm before calculation ¾ The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance ‐ 50 mm)∙( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance ‐ 50 mm)∙10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Smallest distance from the antenna and radiating structures or outer surface of the device The minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] SAR Test Exclusion Thresholds Channel and Mode Frequency (GHz) Maximum source‐based time averaged conducted output power including tune‐up tolerance (mW) Minimum separation distance (mm) Result of Eq. 1 Limit for 1‐g SAR Limit for 10‐g extremity SAR Verdict 802.11b Ch 1 2.412 6.653 mW 5mm 2.06 3.0 7.5 Exempt from SAR 802.11g Ch 11 2.462 4.656 mW 5mm 1.44 3.0 7.5 Exempt from SAR 802.11n (HT20) Ch 6 2.437 4.645 mW 5mm 1.44 3.0 7.5 Exempt from SAR 802.11n (HT40) Ch 9 2.452 4.571 mW 5mm 1.42 3.0 7.5 Exempt from SAR Conclusion Therefore our device complies with FCC’s RF radiation exposure limits for general population without SAR evaluation.

Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 1 on 41 Report Version 1 Test Report No.: FC130226N001 TEST REPORT Applicant: General Procurement, INC. Address: 800 E. Dyer Rd. Santa Ana, Ca 92705, USA Manufacturer or Supplier SHUOYING INDUSTRIAL (SHENZHEN) CO.,LTD Address Shuoying Road, Hebei Industry Area, Dalang, Longhua Town, Baoan, Shenzhen, China Product: 7” tablet Brand Name: iB Sleek Model: PA0755C Additional Model & Model Difference: N/A Date of tests: June 19 ~ July 18 , 2012 the tests have been carried out according to the requirements of the following standards: FCC Part 15, Subpart C (Section 15.247) CONCLUSION: The submitted sample was found to COMPLY with the test requirement Prepared by Glyn He Project Engineer / EMC Department Approved by Sam Tung Manager / EMC Department Date: Feb. 26, 2013 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Bureau Veritas Shenzhen Co., Ltd. Dongguan Branch No. 34, Chenwulu Section, Guantai Rd., Houjie Town, Dongguan City, Guangdong 523942, China Tel: +86 769 8593 5656 Fax: +86 769 8593 1080 Email: [email protected] Page 2 on 41 Report Version 1 Test Report No.: FC130226N001 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................ 4 1 SUMMARY OF TEST RESULTS.................................................................................................... 5 2 MEASUREMENT UNCERTAINTY ................................................................................................ 5 3 GENERAL INFORMATION ............................................................................................................6 3.1 GENERAL DESCRIPTION OF EUT .......................................................................................... 6 3.2 DESCRIPTION OF TEST MODES ............................................................................................ 7 3.2.1. CONFIGURATION OF SYSTEM UNDER TEST ............................................................... 7 3.2.2. TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL.................................... 8 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................................ 10 3.4 DESCRIPTION OF SUPPORT UNITS..................................................................................... 10 4. TEST TYPES AND RESULTS...................................................................................................... 11 4.1 CONDUCTED EMISSION MEASUREMENT........................................................................... 11 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ................................................11 4.1.2 TEST INSTRUMENTS......................................................................................................11 4.1.3 TEST PROCEDURES ..................................................................................................... 12 4.1.4 DEVIATION FROM TEST STANDARD ........................................................................... 12 4.1.5 TEST SETUP................................................................................................................... 13 4.1.6 EUT OPERATING CONDITIONS .................................................................................... 13 4.1.7 TEST RESULTS .............................................................................................................. 14 4.2 RADIATED EMISSION MEASUREMENT ............................................................................... 16 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT .................................................... 16 4.2.2 TEST INSTRUMENTS..................................................................................................... 17 4.2.3 TEST PROCEDURES ..................................................................................................... 18 4.2.4 DEVIATION FROM TEST STANDARD ........................................................................... 18 4.2.5 TEST SETUP................................................................................................................... 19 4.2.6 EUT OPERATING CONDITIONS .................................................................................... 19 4.2.7 TEST RESULTS .............................................................................................................. 20 4.3 6dB BANDWIDTH MEASUREMENT ...................................................................................... 26 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT…

Text truncated - open the document above for the full version.

1 Set-up for radiated emission test <Frequency Range 30MHz~1GHz> <Frequency Range above1GHz> 2 Set-up for conducted emission test