SFIWP5The WP5 is a control module designed for wireless RF communication between other JSFT devices. Applications include crosswalk beacons and warning lights activated via contact-closure relay such as a push-button, sensor, and other devices.

Int egrat ed Inst r uct ions W P5 Module w w w .JSFTech.com 1.800.990.2454 TABLE OF CONTENTS 1.Gen er al In f or m at ion 2.War r an t y 3.Ter m s of Sale 4.Ter m s of Sale 5.WP5 Con f igu r at ion 6.N ot es w w w .JSFTech.com 1.800.990.2454 Specif icat ions and inf ormat ion cont ained in t his manual are current at t ime of print ing, and are subject t o change at any t ime w it hout not ice. FCC ID: SFIW P5 IC: 5301A-W P5 This device complies w it h Part 15 of t he FCC Rules. Operat ion is subject t o t he f ollow ing t w o condit ions: (1) This device may not cause harmf ul int erf erence. (2)This device must accept any int erf erence, including int erf erence t hat may cause undesired operat ion of t he device. Changes or modif icat ions t o t his device, not expressly approved by JSF Technologies Inc.. could void t he user?s aut horit y t o operat e t he equipment . This device complies w it h Indust ry Canada?s license-exempt RSSs. Operat ion is subject t o t he f ollow ing t w o condit ions: (1) This device may not cause int erf erence; and (2) This device must accept any int erf erence, including int erf erence t hat may cause undesired operat ion of t he device. Le présent appareil est conf orme aux CNR d?Indust rie Canada applicables aux appareils radio exempt s de licence. L?exploit at ion est aut orisée aux deux condit ions suivant es: (1) l?appareil ne doit pas produire de brouillage; (2) l?ut ilisat eur de l?appareil doit accept er t out brouillage radioélect rique subi, même si le brouillage est suscept ible d?en compromet t re le f onct ionnement . GENERAL INFORMATION w w w .JSFTech.com 1.800.990.2454 1 The W P5 modular t ransmit t er is only t o be used by JSF Technologies as incorporat ed int o it s ow n product s, and it is not int ended f or sale t o t hird part ies. NOTE WARRANTY INFORM ATION ON LIM ITED WARRANTY Installing, operating or in any other w ay utilizing the product contained in this box means that the original end-use purchaser of the product has read and accepted the terms, conditions and limits of liability and w arranty set out below . WHAT IS COVERED AND FOR HOW LONG? JSF Technologies Inc., 6582 Bryn Rd, Saanichton,British Columbia, Canada w arrants to the original end-use purchaser of the product contained in this box (the ?JSF Product?) that the JSF Product w ill be free from defects in materials and w orkmanship under normal use and service for a period of five (5) years from the date of delivery follow ing the original purchase by the end user (the ?Warranty Period?). If the JSF Product fails to conform to this Limited Warranty during the Warranty Period, JSF Technologies w ill, at its option and to the extent permitted by law : 1.repair the JSF Product defect at no charge using new parts or refurbished parts that are equivalent to new in performance and reliability; or 2.exchange the JSF Product w ith a product that is new or refurbished that is equivalent to new in performance and reliability and is at least functionally equivalent to the original product. JSF Technologies may request that the original end-use purchaser replace defective parts w ith user-installable new or refurbished parts that JSF Technologies provides in fulfillment of its w arranty obligation. A replacement JSF Product or part, including a user-installable part that has been installed in accordance w ith instructions provided by JSF Technologies, assumes the remaining Limited Warranty of the original JSF Product, if any. When a JSF Product or part is exchanged, any replacement item becomes the property of the original end-use purchaser and the replaced item becomes JSF Technologies? property. Parts provided by JSF Technologies in fulfillment of its Limited Warranty obligation must be used in the JSF Product for w hich w arranty service is claimed. WHAT IS NOT COVERED BY THE LIM ITED WARRANTY? This Limited Warranty applies only to the JSF Product manufactured by or for JSF Technologies. It does not cover the follow ing (collectively ?Ineligible Products?): -consumable parts, such as batteries; -damage cause by accident, abuse, misuse, liquid contact, fire, earthquake or external cause; -JSF Products that have been subject to modifications, alterations, tampering, or improper maintenance or repairs; -damage or malfunction resulting from handling, storage, installation, testing, or use noting accordance w ith instructions provided by JSF Technologies; -damage caused by normal w ear and tear or otherw ise due to the normal aging of the JSF Product; -inoperability due to the lack of or insufficient cellular netw ork coverage; -in the case of the solar-pow ered or supplemented JSF Products, inoperability or reduced operability resulting from lack or insufficiency of sunlight. This Limited Warranty does not cover the original end-use purchaser?s cost or expense arising from inspecting, testing, reinstalling, replacing (in w hole or in part) the JSF Product. JSF Technologies does not w arrant that the JSF Product w ill be error-free or w ill operate w ithout interruption. The performance of the JSF Product may be affected by outage, limitation, delays and other problems inherent in the use of the Internet, cellular netw ork, and electronic radio communications. It is the sole responsibility of the end-use purchaser to determine the suitability and proper placement and location of the JSF Product. JSF Technologies is not responsible for any delays, scheduling failures, or other damage or interruption of use resulting from such problems and, w ithout limitation, none of the follow ing: inadequate w ireless netw ork reception in the location of installation of the JSF Product; w ireless netw ork, cellular, or Internet quality of service issues; radio frequency interference w ith the JSF Product; SM S delivery delays related to w ireless netw ork or cellular quality or outage; Internet or cellular service provider outages; ow ner or operator error. The JSF Product is not designed f or …

Text truncated - open the document above for the full version.

TECHNOLOGIES SOLAR TRAFFIC SOLUTIONS Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road 6582 Bryn Road Victoria, BC V8M 1X6 Phone: (800) 990-2454 Web: www.jsftech.com Subject: Manufacturer's Declaration for compliance with FCC PART 15 UNLICENSED MODULAR TRANSMITTER APPROVAL of Sec 15.212 & Pubic Notice# DA 00- 1407 FCC ID: SF/WPS Dear Sir/Madam: The applicant hereby confirms that the following requirements per FCC PART 15 Unlicensed Modular Transmitter Approval of Sec 15.212 & Pubic Notice# DA 00-1407 are met for Limited Modular Approval certification: Modular Approval Checklist: Modular approval requirement 1. The modular transmitter must have its own RF shielding. This is intended to ensurethatthemoduledoesnothaveto rely upon the shielding provided by the device into which it is installed in order for all modular transmitter emissions to comply with Part 15 limits. It is also intended to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed. Such coupling may result in non-compliant operation. 2. TI1e modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. 3. The modular transmitter must have its own power supply regulation. This is intended to ensure that the module will comply with Part 15 requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be pennanently attached or employ a "unique" antenna coupler (at all connections between the module and the antenna, including the cable). Any antenna used with the module must be approved with the module, either at the time of initial authorization or through a Class II pem1issive change. The "professional installation" -provision of Section 15.203 Page 1 Yes Y e s. The module contains a metal shield which co vers allRF components and circuitiy. This is the metal en closure of the WP5. Yes. The module contains buffered data inputs to prevent excessive data rates or over­ modulation. Yes. The module contains its own power supply regulation. Please refer to the sch em a tic with this application No(*) Yes. The WP 5 meets the requirements of Sections 15.203 and 15.204(c) as the WP5 will only ever be professionally installed into host devices manufactured by us, JSFT, the grantee. �SF TECHNOLOGIES SOLAR TRAFFIC SOLUTIONS may not be applied to modules. 5.TI1e modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the transmitter module will be batte1y powered, it must comply with the AC line conducted requirements found in Section 15 .207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites; unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(i)). 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains Transmitter Module FCC ID: XYZMODELl" or "Contains FCC ID: XYZMODELl." Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included m the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and tinling requirements that must be met before a transmitter is authorized for operation under Section 15 .231. For instance, data transmission is prohibited, except for operation under Section 15.23l(e), in which case there are separate field strength level and tinling requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, Page 2 6582 Bryn Road Victoria, BC V8M 1X6 Phone: (800) 990-2454 Web: www.jsftech.com Yes. The module was tested in a stand­ a lone fashion. Yes. The module will be labelled with its own FCC ID a nd all host devices will be labelled to say it contains the module with FCC ID SFIWP5. Yes Yes NOTE: This application is for a Limited Modular Approval, not a Single Modular Approval, as the WP5 will be limited to integration into host devices made by the grantee only, JSF Technologies.

SW Network Address Flash Duration Flash Patt ern M i n u t e s S e c o n d s H o u r s 60 30 60 50 45 40 35 25 30 20 18 15 5 2 3 4 7 6 5 4 3 2 1 0 15 14 13 12 11 10 9 8 Test JSF Strobe Wig-Wag MUTCD Wig-Wag RRFB (WW+S) MUTCD Strobe t e s e R by the manufacturer could void the user's authority to operate the equipment. “This equipment complies wi th FCC Rules, Pa rt 15 and Industry Canada's ICES 003 for a Class A Digital Device. Ope ration is subject to two co nditions: 1) This device may not cause harmful interference, and 2) This device must acc ept any interference that may cause any undesir ed operation” “Cet Apparr eil numerique de la Classe A respe cte toutes les exigences du Reglement sur le materia l broilleur du Canada.” FCC ID: SFIWP5 IC: 5301A-WP5 part: L-938 serial: Model: WP5 JSF Current Driver RRFB Sign LEDs S2 (Legacy) GE

QAI Laboratories 3980 North Fraser Way Burnaby, BC, V5J 5K5 Canada INTENTIONAL RADIATOR TEST REPORT Report Reference Number: E11168-2001_JSF Technologies_Wireless Pla tform 5_Rev-1.0 Tota l Number of Pa ges: 30 Da te of Issue: August 24, 2020 EMC Test Laboratory: QAI Laboratories Ltd. Address: 3980 North Fra ser Wa y, Burna by, BC, V5J 5K5 Ca na da Phone: (604) 527-8378 Fa x: (604) 527-8368 Laboratory Accreditations (per ISO/IEC 17025:2017) American Association for Laboratory Accreditation Certificate Number: 3657.02 This report has been completed in accordance with the requirements of ISO/IEC 17025. Test results contained in this report are within QAI Laboratories ISO/IEC 17025 accreditations. QAI Laboratories authorizes the applicant to reproduce this report, provided it is reproduced in its entirety and for the use by the company’s employees only. Manufacturer: JSF Technologies Inc. Address: 6582 Bryn Rd. Victoria BC, Ca na da V8M 1X6 Equipment Tested: WP5 Wireless Platform 5 Model Number(s): WP5 FCC ID: SFIWP5 ISED ID: 5301A-WP5 QAI Laboratories 3980 North Fraser Way Burnaby, BC, V5J 5K5 Canada Manufacturer: JSF Technologies Inc. Report Number: E11168-2001_JSF Technologies_Wireless Platform 5_Rev-1.0 Page 2 of 30 REVISION HISTORY Date Report Number Details Author’s Initials August 24, 2020 E11168-2001_JSF Technologies_Wireless Platform 5_Rev-1.0 Final RS August 19, 2020 E11168-2001_JSF Technologies_Wireless Platform 5_Rev-0.0 Draft RS All previous versions of this report have been superseded by the latest dated revision as listed in the above table. Please dispose of all previous electronic and paper printed revisions accordingly. REPORT AUTHORIZATION The da ta documented in this report is for the test equipment provided by the ma nufacturer. The tests were conducted on the sa mple equipment a s requested by the ma nufacturer for the purpose of demonstra ting complia nce with the sta nda rds outlined in Section I of this report a s a greed upon by the Ma nufacturer under the quote 20SH07092R1. The Ma nufacturer is responsible for the tested product configura tions, continued product complia nce, a nd for the a ppropriate a uditing of subsequent products a s required. This report ma y comprise a pa rtia l list of tests tha t a re required for FCC a nd ISED Decla ra tion of Conformity ca n only be produced by the ma nufacturer. This is to certify tha t the following report is true a nd correct to the best of our knowledge. __________________ __________________ Testing Performed by Jack Qin EMC Test Engineer Report Prepa red by Ravi Sharma EMC Technica l Writer ____________________ ___________________ Reviewed by Rick Hiebert EMC Project Ma na ger Approved by Parminder Singh Director of EMC Depa rtment QAI Laboratories 3980 North Fraser Way Burnaby, BC, V5J 5K5 Canada Manufacturer: JSF Technologies Inc. Report Number: E11168-2001_JSF Technologies_Wireless Platform 5_Rev-1.0 Page 3 of 30 QAI FACILITIES British Columbia QAI Laboratories Inc. Main Laboratory/Headquarters 3980 North Fraser Way, Burnaby, BC V5J Canada Ontario QAI Laboratories Inc. 25 Royal Group Crescent #3, Vaughan, ON L4H 1X9 Canada Virginia QAI Laboratories Ltd. 1047 Zachary Taylor Hwy, Suite A Huntly, VA 22640 USA China QAI Laboratories Ltd Room 408, No. 228, Jiangchang 3 rd Road Jing’An District, Shanghai, China 200436 California QAI Laboratories Ltd. 8385 White Oak Avenue Rancho Cucamonga, CA 91730 USA Oklahoma QAI Laboratories Ltd. 5110 North Mingo Road Tulsa, OK 74117, USA Miami QAI Laboratories Ltd. 8148 NW 74th Ave, Medley, FL 33166 USA South Korea QAI Laboratories Ltd #502, 8, Sanbon-ro 324beon-gil Gunpo-si, Gyeonggi-do, 15829, South Korea QAI EMC ACCREDITATION QAI EMC is your one-stop regulatory compliance partner for electromagnetic compatibility (EMC) and electromagnetic interference (EMI). Products are tested to the latest and applicable EMC/EMI requirements for domestic and international markets. QAI EMC goes above and beyond being a testing facility—we are your regulatory compliance partner. QAI EMC has the capability to perform RF Emissions and Immunity for all types of electronics manufacturing including Industrial, Scientific, Medical, Information Technology, Telecom, Wireless, Automotive, Marine and Avionics. EMC Laboratory Location FCC Designation (3m SAC) IC Registration (3m SAC) A2LA Certificate Burna by, BC, Ca na da CA9543 21146-1 3657.02 EMC Facility Burnaby BC, Canada QAI Laboratories 3980 North Fraser Way Burnaby, BC, V5J 5K5 Canada Manufacturer: JSF Technologies Inc. Report Number: E11168-2001_JSF Technologies_Wireless Platform 5_Rev-1.0 Page 4 of 30 TABLE OF CONTENTS REVISION HISTORY ................................................................................................................................................................................. 2 REPORT AUTHORIZATI ON.................................................................................................................................................................... 2 QAI FACILITIES.......................................................................................................................................................................................... 3 QAI EMC ACCREDIT ATION................................................................................................................................................................... 3 TABLE OF CONTE NTS ............................................................................................................................................................................. 4 Section I: GENERAL INF ORMATION.......................................................................................................................................... 5 1.1 Product Description ....................................................................................................................................................... 5 1.2 Environmenta l Conditions...…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOS Radiated Emissions Below 30MHz Radiated Emissions 30MHz – 1GHz Radiated Emissions above 1GHz