SJ8RX200WIRELESS RECEIVER

900MHz Wireless Receiver system Congratulations on your purchase of the 900 MHz Wireless Receiver Systems (WRS45234). WRS45234 consists of a wireless receiver and a wireless color Camera, The WRS45234 Wireless receiver surveillance system is an ideal combination for monitoring the porch, watching the yard, pool, pets or the baby. It is also suited to many small businesses. . FEATURES • 900MHz wireless technology • Antenna orientations is adjustable • Both audio and video output • Two channels selection for cameras • Supports up to 2 cameras • Manual or auto switching between cameras • Adjustable cycle time between different channels • Sound and light indication in alarm state • Alarm sound ON/OFF selection • Adjustable alarm sensitivity • Channel lock • AC power adaptor or batterynot includes operation. SYSTEM CONTENTS •RX200-900 wireless receiver x1 •CA330 wireless color camera x1 •Power adaptor x2 •Adaptor cable x1 •Hardware kit x1 •Manual x1 THINGS TO CONSIDER BEFORE INSTALLATION For best performance, follow these simple guidelines: • Camera(s) should be installed between 8 and 13 feet above the area to be monitored • The Camera should be aimed accordingly to optimize viewing area • For best transmission, avoid installations where there are thick walls or major obstructions between the Camera and Receiver INSTALLING THE CAMERA (TRANSMITTER) 1. Unpack the Camera. 2. Decide whether the Camera will be wall-mounted or sit on a desk/table top. If wall mounting there is a useful drilling guide on the back cover of these instructions. Use the hardware kit in the package to fix the camera. The Camera can be adjusted for either mounting scenario by rotating the Camera to the required position. 3. Decide whether to connect using AC power or battery. If using battery install the 9V LI-polymer special battery to the camera. If using the 9V camera power adapter, just connect power jack. Make sure the Camera is positioned no more than 5 1/2 feet from an AC power outlet. 4. Select the Camera operating channel under the housing of the camera by moving the slide switch to position 1 or 2. Switch is preset to channel 1 . The Camera (Transmitter) installation is now complete. SETTING UP THE RECEIVER 1. Connect one end of the cable (RCA <male>) to the rear of the receiver, another end (RCA cord) to your television's A/V inputs, the yellow plug to the VIDEO IN jack and the white plug to the AUDIO IN jack. 2. Plug the receiver power adapter into the 9V DC power jack on the back of the receiver and plug the power adapter into any 120 V/240 V power outlet. 3. Place the receiver either on top or near to your TV. Rotate the antenna to a vertical position. OPTIMIZING THE WIRELESS CAMERA SYSTEM The 900MHz video signals pass easily through your home’s interior walls, but the signal may be reflected by power wires or plumbing inside the wall. Usually a slight adjustment of the Receiver and/or Camera antenna will improve reception. Take care not to force the antennas past their lock positions. The most common source of interference is microwave ovens and cell phones. Try to avoid mounting the Receiver near a microwave oven or other source of RF interference such as cordless phones. MULTI-CAMERA OPERATION This 900MHz wireless surveillance system is designed to work with up to 2 Cameras. Additional Cameras (With different shapes for your option) are sold separately. IMPORTANT: When using more than one Camera, make sure each camera is assigned to a specific channel by adjusting the corresponding slide switch position. Accordingly the slide switch located on the rear of the Receiver should be adjusted to reflect the channels in use. OPERATING THE SYSTEM Set your TV to monitor the VIDEO INPUT designated for the Receiver. The receiver can support up to two different camera/transmitter signals. You can switch from one camera to the next either manually or automatically via button on the top panel of the receiver. MANUAL MODE To select one of the two channels manually, press the MANUAL button on the top panel of the receiver. The red LED will light and the receiver will switch to a different channel (CAM1, CAM2) each time when the MANUAL button is pressed. To avoid searching channels that do not have cameras/transmitters assigned to them, set the slide switch (located on the rear panel of the receiver) for those corresponding position. When you have selected a channel with an active camera, that video will appear on your TV screen. CAM1 IN USECAM1 AND 2 IN USEALL IN USE AUTO MODE To have the receiver automatically rotate through the channels, press the AUTO button on the top panel of the receiver. The green LED will light and the receiver will continuously scan through all channels which are ON. To avoid searching channels that do not have cameras/transmitters assigned to them, set the slide switch for those corresponding position. The monitor will display the picture from one camera to the next. DWELL TIME SETTING The dwell time (time taken to switch between cameras) is preset to 4 seconds and can be adjusted between 2-30 seconds. To adjust the dwell time, press both the AUTO and MANUAL button simultaneously. Each flash of the LED increases the dwell time by one second. You can verify the time you setting by counting the flashing LED when you released, one flash stand for 1 second. ALARM SOUND SETTING You can press the ON/OFF button on the front panel of the receiver to open/close the alarm sound ALARM SENSITIVITY SETTING You can adjust the alarm sensitivity of the receiver by turning the alarm sensitivity adjust knob at the rear of the receiver. TROUBLE SHOOTING If you are having trouble operating this product, please consult the guide below: SYMPTOM REMEDIES No camera picture 1. Check all connectors. Make sure camera(s) and receiver are switched ON. 2. Ensure camera(s) and receiver are set to correct channel(s). 3. Make sure camera is within range of receiver. Blank monitor 1. Make sure receiver is switched ON. 2. If us…

Text truncated - open the document above for the full version.

EUT - Front View EUT - Back View

FCC ID Label Sample for Model: RX200, 45234R FCC ID: SJ8RX200 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID Label This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. Proposed Label Location on EUT EUT Top View/ proposed FCC Mark Location FCC ID:SJ8RX200 This device com plies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any ifi

PCB1 - Front View PCB1 - Back View PCB2 - Front View PCB2 - Back View

RX200 Wireless Receiver Nov, 29th, 2007 Architecture RX200 Wireless Receiver includes received high quality video and audio components, The unit is a wireless receiver compatible with any RDI or compatible wireless camera, an ideal product for monitoring the porch, watching the yard, pool, pets or the baby. It is also suited to many small business applications. RX200 hardware architecture is show in Figure 1. 1> The 900MHz RX module is assigned to receive the video and audio signal wirelessly. 2> MCU(Micro control unit) operates periodically . Including control Manual, Auto button ,control dip switcher to select RF module channel , control sound trigger, control LED display RF module channel, etc.

FCC TEST REPORT Page 1 of 18 FCC ID NO. : SJ8RX200 Applicant : RDI Technology (Shenzhen) Co., Ltd. Building C1 Xingtang Industrial Park, East Baishixia, Fuyong, Baoan, Shenzhen, P.R.C. Equipment Under Test (EUT) : Product Name : Wireless Receiver Model No. : RX200, 45234R Standards : FCC Part 15 SUBPART B Date of Test : Dec.6, 2007 Test Engineer : Tiger Su Reviewed By : PERPARED BY: Waltek Services (Shenzhen) Co., Ltd. 8C,West Tower, Aidi Building, No.5003 Binhe Rd, Futian District, Shenzhen518045, Guangdong, China. Tel: 86-755-83551033 Fax: 86-755-83552400 RDI Technology (Shenzhen) Co., Ltd. FCC ID: SJ8RX200 Page 2 of 18 2 Test Summary Test Test RequirementTest Method Class / Severity Result Radiated Emission (30MHz to 5GHz) FCC PART 15, SUBPART B: 2003 ANSI C63.4: 2003 Class B PASS Conducted Emission (150KHz to 30MHz) FCC PART 15, SUBPART B: 2003 ANSI C63.4: 2003 Class B PASS RDI Technology (Shenzhen) Co., Ltd. FCC ID: SJ8RX200 Page 3 of 18 3 Contents Page 1 COVER PAGE..........................................................................................................................................................1 2 TEST SUMMARY....................................................................................................................................................2 3 CONTENTS ..............................................................................................................................................................3 4 GENERAL INFORMATION..................................................................................................................................4 4.1 CLIENT INFORMATION............................................................................................................................................4 4.2 GENERAL DESCRIPTION OF E.U.T...........................................................................................................................4 4.3 DETAILS OF E.U.T. .................................................................................................................................................4 4.4 DESCRIPTION OF SUPPORT UNITS...........................................................................................................................4 4.5 TEST FACILITY........................................................................................................................................................5 4.6 TEST LOCATION......................................................................................................................................................5 5 EQUIPMENT USED DURING TEST ...................................................................................................................6 5.1 CONDUCTION EMISSIONS, 0.15MHZ TO 30MHZ.....................................................................................................7 5.1.1 E.U.T. Operation..........................................................................................................................................7 5.1.2 Measurement Result .....................................................................................................................................8 5.1.3 Measurement Data .......................................................................................................................................9 5.2 RADIATED EMISSIONS, 30MHZ TO 5GHZ.............................................................................................................10 5.2.1 E.U.T. Operation........................................................................................................................................10 5.2.2 EUT Setup ..................................................................................................................................................10 5.2.3 Spectrum Analyzer Setup............................................................................................................................11 5.2.4 Test procedure............................................................................................................................................11 5.2.5 Summary of Test Results ............................................................................................................................11 5.2.6 Radiatied Emissions Test Data ..................................................................................................................12 5.3 PHOTOGRAPHS - TEST SETUP................................................................................................................................13 5.3.1 Conduction Emissions Test Setup ..............................................................................................................13 5.3.2 Radiated Emissions Test Setup For 30MHz-1000MHz ..............................................................................14 5.3.3 Radiated Emissions Test Setup For 1GHz-5GHz.......................................................................................14 5.3.4 EUT - Front View .......................................................................................................................................15 5.3.5 EUT - Back View ........................................................................................................................................15 5.3.6 PCB1 - Front View .....................................................................................................................................16 5.3.7 PCB1 - Back View ......................................................................................................................................16 5.3.8 PCB2 - Front View .....................................................................................................................................17 5.3.9 PCB2 - Back View ..................................................................................................…

Text truncated - open the document above for the full version.

Conduction Emissions Test Setup Radiated Emissions Test Setup