SNE-DOOR-003Eve Door & Window

Eve Systems LLC 100 Pine St., Suite 1250, San Francisco CA 94111, USA Eve Systems GmbH Rotkreuzplatz 1 80634 München Germany - RF circuit function: The product are based on the nRF52840 modules The major part of this IC is a Bluetooth, IEEE 802.15.4-2006, Proprietary 2.4GHz compliant transceiver. The Proprietary 2.4GHz function of this product will be turned off using software. Will not be used by the final consumer. Philipp Guse Title: Senior Product Manager Signature:

Appendix P Photo Documentation Page 1 of 7 60362204 001, 60362205 001 Product: Eve Door & Window Type Identification: 20EBN9901 Appendix P Photo Documentation Page 2 of 7 60362204 001, 60362205 001 Product: Eve Door & Window Type Identification: 20EBN9901 Appendix P Photo Documentation Page 3 of 7 60362204 001, 60362205 001 Product: Eve Door & Window Type Identification: 20EBN9901 Appendix P Photo Documentation Page 4 of 7 60362204 001, 60362205 001 Product: Eve Door & Window Type Identification: 20EBN9901

Appendix P Photo Documentation Page 5 of 7 60362204 001, 60362205 001 Product: Eve Door & Window Type Identification: 20EBN9901 Antenna Appendix P Photo Documentation Page 6 of 7 60362204 001, 60362205 001 Product: Eve Door & Window Type Identification: 20EBN9901 Appendix P Photo Documentation Page 7 of 7 60362204 001, 60362205 001 Product: Eve Door & Window Type Identification: 20EBN9901

Produkte Products Prüfbericht - Nr.: Test Report No. 60362204 001 Seite 35 von 40 Page 35 of 40 6. Safety Human exposure 6.1 Radio Frequency Exposure Compliance 6.1.1 Electromagnetic Fields RESULT: Passed Test standard : FCC KDB Publication 447498 D01 v06 FCC CFR 47 Part 2 Subpart J Section 2.1091 ISED RSS-102 issue 5, 2.5.2 Separation distance is more than 20 cm, thus mobile device exposure limits can be applied. FCC Maximum Exposure: Mode Frequenc y (MHz) Antenna Gain (dBi) Antenna Gain (numeric) Maximum Output Power (dBm) Output Power (mW) Power Density (S)(mW/cm 2 ) Test Result BLE 2480 3.02 2.0045 4.61 2.8907 0.001153 Pass Limit FCC: 1500-100,000 MHz 1.0 mW/cm 2 ISED: Exemption Limits for Routine Evaluation – RF Exposure Evaluation At or above 300MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 × 10 -2 f 0.6834 W, where f is in MHz; f= 2480MHz 1.31 × 10 -2 × 2480 0.6834 = 2.74W After evaluation the 2480MHz e.i.r.p 7.63dBm calculated result is closer to its limit. 7.63dBm = 0.00579W, it is well below the limit of Exemption Limits for Routine Evaluation, so RF exposure assessment meets its standards.

Produkte Products Prüfbericht - Nr.: Test Report No. 60362205 001 Seite 28 von 33 Page 28 of 33 6. Safety Human exposure 6.1 Radio Frequency Exposure Compliance 6.1.1 Electromagnetic Fields RESULT: Passed Test standard : FCC KDB Publication 447498 D01 v06 FCC CFR 47 Part 2 Subpart J Section 2.1091 ISED RSS-102 issue 5, 2.5.2 Separation distance is more than 20 cm, thus mobile device exposure limits can be applied. FCC Maximum Exposure: Mode Frequenc y (MHz) Antenna Gain (dBi) Antenna Gain (numeric) Maximum Output Power (dBm) Output Power (mW) Power Density (S)(mW/cm 2 ) Test Result Thread 2480 3.02 2.0045 8.09 6.4417 0.002570 Pass Limit FCC: 1500-100,000 MHz 1.0 mW/cm 2 ISED: Exemption Limits for Routine Evaluation – RF Exposure Evaluation At or above 300MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 × 10 -2 f 0.6834 W, where f is in MHz; f= 2480MHz 1.31 × 10 -2 × 2480 0.6834 = 2.74W After evaluation the 2480MHz e.i.r.p 11.11dBm calculated result is closer to its limit. 11.11dBm = 0.01291W, it is well below the limit of Exemption Limits for Routine Evaluation, so RF exposure assessment meets its standards.

Test Report No.60362204 001 Appendix D: Radiated and Mains Spurious Emission Data (File: 60362204 001AppendixD) Contents Spurious Emiss ions , Band Edges for BLE 1M ......................................................................................... 2 Spurious Emiss ions , TX Mode, 9kH z-30MH z for BLE 1M .....................................................................14 Spurious Emiss ions , TX Mode, 30MHz-1GH z for BLE 1M ....................................................................16 Spurious Emiss ions , TX Mode, 1GHz-26.5GH z for BLE 1M..................................................................18 Spurious Emiss ions , Band Edges for BLE 2M ........................................................................................24 Spurious Emiss ions , TX Mode, 1GHz-26.5GH z for BLE 2M..................................................................36 2 Spurious Emissions, Band Edges for BLE 1M 2402MHz 3 4 5 6 2440MHz 7 8 9 10 2480MHz 11 12 13 14 Spurious Emissions, TX Mode, 9kHz-30MHz for BLE 1M 2402MHz 15 16 Spurious Emissions, TX Mode, 30MHz-1GHz for BLE 1M 2402MHz 17 18 Spurious Emissions, TX Mode, 1GHz-26.5GHz for BLE 1M 2402MHz 19 20 2440MHz 21 22 2480MHz 23 24 Spurious Emissions, Band Edges for BLE 2M 2402MHz 25 26 27 28 2440MHz 29 30 31 32 2480MHz 33 34 35 36 Spurious Emissions, TX Mode, 1GHz-26.5GHz for BLE 2M 2402MHz 37 38 2440MHz 39 40 2480MHz 41

Prü fbericht - Produkte Test Report - Products Prü fbericht-Nr.: Test report no.: 60362204 001 Auftrags-Nr.: Order no.: 238484596 Seite 1 von 40 Page 1 of 40 Kunden-Referenz-Nr.: Client reference no.: N/A Auftragsdatum: Order date: 2020.04.07 Auftraggeber: Client: Eve Systems LLC 100 Pine St., Suite 1250, San Francisco CA 94111 USA Prü fgegenstand: Test item: Eve Door & Window Bezeichnung / Typ-Nr.: Identification / Type no.: 20EBN9901 Auftrags-Inhalt: Order content: FCC Part 15C / ISED RSS-247 Test report (BLE) Prü fgrundlage: Test specification: FCC 47CFR Part 15: Subpart C Section 15.247 ISED RSS-247 (02-2017) Wareneingangsdatum: Date of sample receipt: 2020.04.17 Prü fmuster-Nr.: Test sample no: A002803776-002 Prü fzeitraum: Testing period: 2020.04.17 - 2020.05.04 Ort der Prü fung: Place of testing: EMC/RF Laboratory Taipei Prü flaboratorium: Testing laboratory: Taipei Testing laboratories Prü fergebnis*: Test result*: Pass ü berprü ft von: reviewed by: M a r s Y . J . L i n genehmigt von: authorized by: Ryan W . T. C h e n atum: 2020.06.04 Date: Datum: 2020.06.04 Date: Stellung / Position: Project Engineer Stellung / Position: Project Manager Sonstiges / Other: Zustand des Prü fgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhaft P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet * Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prü fbericht bezieht sich nur auf das o.g. Prü fmuster und darf ohne Genehmigung der Prü fstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prü fzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark. TUV Rheinland Taiwan Ltd. 11F., No. 758, Sec. 4, Bade Rd., Taipei 105, Taiwan, R.O.C. Produkte Products Prü fbericht - Nr.: Test Report No. 60362204 001 Seite 2 von 40 Page 2 of 40 TEST SUMMARY 5.1.1 ANTENNA REQUIREMENT RESULT: Passed 5.1.2 MAXIMUM CONDUCTED PEAK OUTPUT POWER RESULT: Passed 5.1.3 6DB BANDWIDTH AND 99% BANDWIDTH RESULT: Passed 5.1.4 POWER DENSITY RESULT: Passed 5.1.5 CONDUCTED SPURIOUS EMISSIONS AND FREQUENCY BAND EDGE MEASURED IN 100KHZ BANDWIDTH RESULT: Passed 5.1.6 SPURIOUS EMISSION RESULT: Passed 6.1.1 ELECTROMAGNETIC FIELDS RESULT: Passed Produkte Products Prü fbericht - Nr.: Test Report No. 60362204 001 Seite 3 von 40 Page 3 of 40 Contents 1. GENERAL REMARKS ............................................................................................... 5 1.1 COMPLEMENTARY MATERIALS ................................................................................. 5 1.2 DECISION RULE OF CONFORMITY.............................................................................. 5 2. TEST SITES ............................................................................................................ 6 2.1 TEST LABORATORY ................................................................................................ 6 2.2 TEST FACILITY ........................................................................................................ 6 2.3 LIST OF TEST AND MEASUREMENT INSTRUMENTS ...................................................... 7 2.4 TRACEABILITY ........................................................................................................ 8 2.5 CALIBRATION ......................................................................................................... 8 2.6 MEASUREMENT UNCERTAINTY ................................................................................. 8 3. GENERAL PRODUCT INFORMATION ........................................................................... 9 3.1 PRODUCT FUNCTION AND INTENDED USE ................................................................. 9 3.2 SYSTEM DETAILS AND RATINGS ............................................................................... 9 3.3 INDEPENDENT OPERATION MODES ......................................................................... 10 3.4 NOISE GENERATING AND NOISE SUPPRESSING PARTS ............................................ 10 3.5 SUBMITTED DOCUMENTS ....................................................................................... 10 4. TEST SET-UP AND OPERATION MODES ................................................................... 11 4.1 PRINCIPLE OF CONFIGURATION SELECTION ............................................................ 11 4.2 TEST OPERATION AND TEST SOFTWARE................................................................. 11 4.3 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ............................................... 12 4.4 COUNTERMEASURES TO ACHIEVE EMC COMPLIANCE .............................................. 12 4.5 TEST SETUP DIAGRAM .......................................................................................... 12 5. TEST RESULTS ..................................................................................................... 14 5.1 TRANSMITTER REQUIREMENT & TEST SUITES ......................................................... 14 5.1.1 Antenna Requirement ................................................................................................................ 14 5.1.2 Maximum conducted Peak output power ................................................................................... 15 5.1.3 6dB Bandwidth and 99% Bandwidth .......................................................................................... 16 5.1.4 Power Density ................................................…

Text truncated - open the document above for the full version.

Test Report No.60362205 001 Appendix D: Radiated and Mains Spurious Emission Data (File: 60362205 001AppendixD) Contents Spurious Emiss ions , Band Edges............................................................................................................. 2 Spurious Emiss ions , TX Mode, 9kH z-30MH z ........................................................................................14 Spurious Emiss ions , TX Mode, 30MHz-1GH z .......................................................................................16 Spurious Emiss ions , TX Mode, 1GHz-26.5GH z .....................................................................................18 2 Spurious Emissions, Band Edges 2405MHz 3 4 5 6 2440MHz 7 8 9 10 2480MHz 11 12 13 14 Spurious Emissions, TX Mode, 9kHz-30MHz 2480MHz 15 16 Spurious Emissions, TX Mode, 30MHz-1GHz 2480MHz 17 18 Spurious Emissions, TX Mode, 1GHz-26.5GHz 2405MHz 19 20 2440MHz 21 22 2480MHz 23

Prü fbericht - Produkte Test Report - Products Prü fbericht-Nr.: Test report no.: 60362205 001 Auftrags-Nr.: Order no.: 238484596 Seite 1 von 33 Page 1 of 33 Kunden-Referenz-Nr.: Client reference no.: N/A Auftragsdatum: Order date: 2020.02.25 Auftraggeber: Client: Eve Systems LLC 100 Pine St., Suite 1250, San Francisco CA 94111 USA Prü fgegenstand: Test item: Eve Door & Window Bezeichnung / Typ-Nr.: Identification / Type no.: 20EBN9901 Auftrags-Inhalt: Order content: FCC Part 15C / ISED RSS-247 Test report (Thread) Prü fgrundlage: Test specification: FCC 47CFR Part 15: Subpart C Section 15.247 ISED RSS-247 (02-2017) Wareneingangsdatum: Date of sample receipt: 2020.03.25 Prü fmuster-Nr.: Test sample no: A002810618-001, A002810618-003 Prü fzeitraum: Testing period: 2020.04.17 - 2020.05.04 Ort der Prü fung: Place of testing: EMC/RF Laboratory Taipei Prü flaboratorium: Testing laboratory: Taipei Testing laboratories Prü fergebnis*: Test result*: Pass ü berprü ft von: reviewed by: M a r s Y . J . L i n genehmigt von: authorized by: Ryan W.T. Chen atum: 2020.06.04 Date: Datum: 2020.06.04 Date: Stellung / Position: Project Engineer Stellung / Position: Vice General Manager Sonstiges / Other: Zustand des Prü fgegenstandes bei Anlieferung: Condition of the test item at delivery: Prüfmuster vollständig und unbeschädigt Test item complete and undamaged * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhaft P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet * Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prü fbericht bezieht sich nur auf das o.g. Prü fmuster und darf ohne Genehmigung der Prü fstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prü fzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark. TUV Rheinland Taiwan Ltd. 11F., No. 758, Sec. 4, Bade Rd., Taipei 105, Taiwan, R.O.C. Produkte Products Prü fbericht - Nr.: Test Report No. 60362205 001 Seite 2 von 33 Page 2 of 33 TEST SUMMARY 5.1.1 ANTENNA REQUIREMENT RESULT: Passed 5.1.2 MAXIMUM CONDUCTED PEAK OUTPUT POWER RESULT: Passed 5.1.3 6DB BANDWIDTH AND 99% BANDWIDTH RESULT: Passed 5.1.4 POWER DENSITY RESULT: Passed 5.1.5 CONDUCTED SPURIOUS EMISSIONS AND FREQUENCY BAND EDGE MEASURED IN 100KHZ BANDWIDTH RESULT: Passed 5.1.6 SPURIOUS EMISSION RESULT: Passed 6.1.1 ELECTROMAGNETIC FIELDS RESULT: Passed Produkte Products Prü fbericht - Nr.: Test Report No. 60362205 001 Seite 3 von 33 Page 3 of 33 Contents 1. GENERAL REMARKS ............................................................................................... 5 1.1 COMPLEMENTARY MATERIALS ................................................................................. 5 1.2 DECISION RULE OF CONFORMITY.............................................................................. 5 2. TEST SITES ............................................................................................................ 6 2.1 TEST LABORATORY ................................................................................................ 6 2.2 TEST FACILITY ........................................................................................................ 6 2.3 LIST OF TEST AND MEASUREMENT INSTRUMENTS ...................................................... 7 2.4 TRACEABILITY ........................................................................................................ 8 2.5 CALIBRATION ......................................................................................................... 8 2.6 MEASUREMENT UNCERTAINTY ................................................................................. 8 3. GENERAL PRODUCT INFORMATION ........................................................................... 9 3.1 PRODUCT FUNCTION AND INTENDED USE ................................................................. 9 3.2 SYSTEM DETAILS AND RATINGS ............................................................................... 9 3.3 INDEPENDENT OPERATION MODES ......................................................................... 10 3.4 NOISE GENERATING AND NOISE SUPPRESSING PARTS ............................................ 10 3.5 SUBMITTED DOCUMENTS ....................................................................................... 10 4. TEST SET-UP AND OPERATION MODES ................................................................... 11 4.1 PRINCIPLE OF CONFIGURATION SELECTION ............................................................ 11 4.2 TEST OPERATION AND TEST SOFTWARE................................................................. 11 4.3 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ............................................... 12 4.4 COUNTERMEASURES TO ACHIEVE EMC COMPLIANCE .............................................. 12 4.5 TEST SETUP DIAGRAM .......................................................................................... 12 5. TEST RESULTS ..................................................................................................... 14 5.1 TRANSMITTER REQUIREMENT & TEST SUITES ......................................................... 14 5.1.1 Antenna Requirement ................................................................................................................ 14 5.1.2 Maximum conducted Peak output power ................................................................................... 15 5.1.3 6dB Bandwidth and 99% Bandwidth .......................................................................................... 16 5.1.4 Power Density .............................…

Text truncated - open the document above for the full version.

Produkte Products Prüfbericht - Nr.: Test Report No. 60362193 001 Seite 37 von 41 Page 37 of 41 7. Photographs of the Test Set-Up Photograph 1: Set-up for Spurious Emissions (Front View 1) Photograph 2: Set-up for Spurious Emissions (Front View 2) Produkte Products Prüfbericht - Nr.: Test Report No. 60362193 001 Seite 38 von 41 Page 38 of 41 Photograph 3: Set-up for Spurious Emissions (Back View 1) Photograph 4: Set-up for Spurious Emissions (Back View 2) Produkte Products Prüfbericht - Nr.: Test Report No. 60362193 001 Seite 39 von 41 Page 39 of 41 Photograph 5: Set-up for Spurious Emissions (Back View 3) Photograph 6: Set-up for Spurious Emissions (Back View 4) Produkte Products Prüfbericht - Nr.: Test Report No. 60362193 001 Seite 40 von 41 Page 40 of 41 Photograph 7: Set-up for Conducted Testing (View 1) Photograph 8: Set-up for Conducted Testing (View 2)