SVC-NADD7050Direct Digital Network Amplifier

® D 7050 Direct Digital Network Amplifier ENGLISH PORTUGUÊS FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ Owner’s Manual SAVE THESE INSTRUCTIONS FOR LATER USE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE AUDIO EQUIPMENT. 1 Read instructions - All the safety and operating instructions should be read before the product is operated. 2 Retain instructions - The safety and operating instructions should be retained for future reference. 3 Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4 Follow Instructions - All operating and use instructions should be followed. 5 Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Clean only with a dry cloth. 6 Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7 Water and Moisture - Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 8 Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 9 A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10 Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 11 Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. The primary method of isolating the amplifier from the mains supply is to disconnect the mains plug. Ensure that the mains plug remains accessible at all times. Unplug the AC power cord from the AC outlet if the unit will not be used for several months or more. 12 Grounding or Polarization - This product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 13 Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14 Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. NOTE TO CATV SYSTEM INSTALLER This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 15 Lightning - For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power line surges. 16 Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17 Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 18 Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. WARNING: THE APPARATUS SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING, AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THE APPARATUS. AS WITH ANY ELECTRONIC PRODUCTS, USE CARE NOT TO SPILL LIQUIDS INTO ANY PART OF THE SYSTEM. LIQUIDS CAN CAUSE A FAILURE AND/OR A FIRE HAZARD. 19 Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power supply cord or plug is damaged. b) If liquid has been spilled, or objects …

Text truncated - open the document above for the full version.

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Member of the SGS Group (SGS SA) SGS IECC Limited Units 303-305, 3/F., 31 Lok Yip Road, On Lok Tsuen, Fanling, N.T., Hong Kong Telephone: +852 23052570 Fax: +852 27564480 FEDERAL COMMUNICATIONS COMMISSION CAB Registration number: 446297 No. VF59201 Verification of Conformity for FCC DoC Procedure It is herewith confirmed and found the following designated product Product Name: Digital network receiver Model : D7050 ( Product Identification ) to comply with the technical requirements set up by ANSI C63.4 & CFR 47 FCC PART 15 regulations for the evaluation of electromagnetic compatibility with. Test Report Number(s): 59201 issued on: June 06, 2013 ( Identification of regulations / standards ) Applicant : Lenbrook Industries Limited Address : 633 Granite Court, Pickering Ontario, Toronto L1W 3K1, Canada ( Applicant Identification ) TEST LABORATORY This is the test result, that was carried out based on the submitted sample(s) of the product in conformity with the specification of the respective standards. LOKE Sai Kit, Wilson Senior Manager June 06, 2013 This verification is related to the submitted sample(s) and in conjunction with the test data detailed in the above test report.

SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix A Page: 1 of 5 Page 1 of 5 D7050_External Photos Application No.: SHEM1304000667RF Applicant: Lenbrook Industries Limited Address of Applicant: 633 Granite Court, Pickering Ontario, Toronto L1W 3K1, Canada Equipment Under Test (EUT): Product Name: Direct Digital Network Amplifier Brand Name: NAD Model No.: D7050 DIRECT DIGITAL NETWORK AMPLIFIER FCC ID: SVC-NADD7050 IC: 152C-NADD7050 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix A Page: 2 of 5 Page 2 of 5 1 Contents Page 1 CONTENTS..........................................................................................................2 2 EXTERNAL PHOTOS........................................................................................3 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix A Page: 3 of 5 Page 3 of 5 2 External Photos SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix A Page: 4 of 5 Page 4 of 5 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix A Page: 5 of 5 Page 5 of 5 End

HANSONG(NANJING) TECHNOLOGY CO.,LTD. NO. HS/QR-RD-26 CAD generared drawing Don't manually update SCALE 1 : 1CAD FILE: DWG. NO. A4 SIZE SHEET 1 OF 1 REV. DATEAPPROVALS Drawn by ME Checked by Team leader UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETER TOLERANCES ARE: MATERIAL FINISH DO NOT SCALE DRAWING APPLICATION ITEM PART OR IDENTIFYING NO. NOMENCLATURE OR DESCRIPTION MATERIAL SPECIFICATION QTY REQD PARTS LIST Approved by ME Manager MODEL : PART NO. 3RD ANGLE PROJECTION TOOLING SAMPLE QUOTATION PRODUCTION GB/T1804-m OR ISO 2768-m Checked by Tooling ME PART NAME Lydia HS40-D7050 -B12V1-SR01 D C B A A B C D 123 456 7 8 8 7 6 5 4 32 1 THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF HANSONG(NANJING) TECHNOLOGY CO.,LTD.ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN RERMISSION OF HANSONG(NANJING) TECHNOLOGY CO.,LTD.IS PROHIBITED. REVISIONS REV. CHANGE DETAIL DATE PURPOSE -- -- -- -- -- -- D7050 2013/03/12 D7050 Rear panel silkscreen 67-325001-1D B2013/03/12 C2013/05/20 D 156C更改为152C 2013/06/03

SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix B Page: 1 of 6 Page 1 of 6 D7050_Internal Photos Application No.: SHEM1304000667RF Applicant: Lenbrook Industries Limited Address of Applicant: 633 Granite Court, Pickering Ontario, Toronto L1W 3K1, Canada Equipment Under Test (EUT): Product Name: Direct Digital Network Amplifier Brand Name: NAD Model No.: D7050 DIRECT DIGITAL NETWORK AMPLIFIER FCC ID: SVC-NADD7050 IC: 152C-NADD7050 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix B Page: 2 of 6 Page 2 of 6 1 Contents Page 1 CONTENTS..........................................................................................................2 2 INTERNAL PHOTOS.........................................................................................3 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix B Page: 3 of 6 Page 3 of 6 2 Internal Photos SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix B Page: 4 of 6 Page 4 of 6 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix B Page: 5 of 6 Page 5 of 6 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix B Page: 6 of 6 Page 6 of 6 E EE En nn nd dd d

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. No. 588 West Jindu Road, Songjiang District, Shanghai, China Telephone: +86 (0) 21 61915666 Fax: +86 (0) 21 61915678 [email protected] Report No.: SHEM130400066703 Page 1 of 11 Tony Wu E&E Section Manager SGS-CSTC (Shanghai) Co., Ltd. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only FCC MPE REPORT Application No.: SHEM1304000667RF Applicant: Lenbrook Industries Limited Equipment Under Test (EUT): NOTE: The following sample(s) submitted was/were identified on behalf of the client as Product Name: Direct Digital Network Amplifier Brand Name: NAD Model: D7050 DIRECT DIGITAL NETWORK AMPLIFIER Added Model: N/A FCC ID: SVC-NADD7050 IC: SVC-NADD7050 Standards: 152C-NADD7050 Date of Receipt: April 23, 2013 Date of Test: May 02, 2013 to May 29, 2013 Date of Issue: May 31, 2013 Test Result : PASS* *In the configuration tested, the EUT detailed in this report complied with the standards specified above. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM130400066703 Page: 2 of 11 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 2 Version Revision Record Version Chapter Date Modifier Remark 00 / May 31, 2013 / Original Authorized for issue by: Zenger Zhang Engineer Print Name Susie Liu Clerk Print Name Keny Xu Reviewer Print Name SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM130400066703 Page: 3 of 11 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 3 Contents Page 1 COVER PAGE .............................................................................................................. 1 2 VERSION.....................................................................................................................................2 3 CONTENTS......................................................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. 588 West Jindu Road,Songjiang District,Shanghai,China Telephone: +86 (0) 21 6191 5666 Fax: +86 (0) 21 6191 5678 [email protected] Report No.: SHEM130400066702 Page 1 of 74 Tony Wu E&E Section Manager SGS-CSTC (Shanghai) Co., Ltd. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only FCC Part 15C TEST REPORT Application No. : SHEM1304000667RF Applicant: Lenbrook Industries Limited FCC ID: SVC-NADD7050 IC: 152C-NADD7050 Equipment Under Test (EUT): NOTE: The following sample(s) submitted was/were identified on behalf of the client as Product Name: Direct Digital Network Amplifier Brand Name: NAD Model: D7050 DIRECT DIGITAL NETWORK AMPLIFIER Added Model: N/A Standards: FCC PART 15 SUBPART C, Section 15.247:2012 RSS-210 Issue 8 (December 2010) RSS-Gen Issue 3 (December 2010) Date of Receipt: April 23, 2013 Date of Test: May 02, 2013 to May 29, 2013 Date of Issue: May 31, 2013 Test Result : PASS * * In the configuration tested, the EUT (Equipment under test) complied with the standards specified above. SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM130400066702 Page: 2 of 74 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 2 Version Revision Record Version Chapter Date Modifier Remark 00 / May 31, 2013 / Original Authorized for issue by: Zenger Zhang Engineer Print Name Susie Liu Clerk Print Name Keny Xu Reviewer Print Name SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM130400066702 Page: 3 of 74 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e- document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only 3 Test Summary Test Item FCC Test Requirement IC Test Requirement Test method Result Antenna Requirement FCC Part 15, Subpart C Section 15.203/15.247 (c) RSS-Gen 7.1.2 --- PASS AC Power Line Conducted Emission FCC Part 15, Subpart C Section 15.207 RSS-Gen Section 7.2.4 ANSI C63.10 (2009) Section 6.2 PASS 20dB Oc…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix C Page: 1 of 4 Page 1 of 4 D7050_Test Setup Photos Application No.: SHEM1304000667RF Applicant: Lenbrook Industries Limited Address of Applicant: 633 Granite Court, Pickering Ontario, Toronto L1W 3K1, Canada Equipment Under Test (EUT): Product Name: Direct Digital Network Amplifier Brand Name: NAD Model No.: D7050 DIRECT DIGITAL NETWORK AMPLIFIER FCC ID: SVC-NADD7050 IC: 152C-NADD7050 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix C Page: 2 of 4 Page 2 of 4 1 Contents Page 1 CONTENTS...............................................................................................................2 2 EQUIPMENT UNDER TEST PICTURES.............................................................3 2.1 Radiated Emission Test Setup.............................................................3 2.2 Conducted Emission Test Setup..........................................................4 SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix C Page: 3 of 4 Page 3 of 4 2 EQUIPMENT UNDER TEST PICTURES 2.1 Radiated Emission Test Setup 30MHz to 1GHz Above 1GHz SGS-CSTC Standards Technical Services (Shanghai)Co., Ltd. Report No.: SHEM1304000667RF －Appendix C Page: 4 of 4 Page 4 of 4 2.2 Conducted Emission Test Setup End