SWN-PT20CPathfinder2

1 PATHFINDER2 SERIES PATHFINDER2: PT20C, PR20C PATHFINDER2 MINI: PT20C, PM20C EXPLORE MORE - ADVANCED GPS TRACKING & TRAINING Owner's Manual Please read this manual thoroughly before operating the Dogtra PATHFINDER2 series. ENGLISH 2 IMPORTANT SAFETY AND PRODUCT INFORMATION WARNING Please read all safety and product information below before using your Dogtra product. Failure to follow these safety instructions could result in injury to you, your dog and others, or it could result in damage to your Dogtra product or other property. DOG SAFETY Proper Use Dogtra products should be used to train, educate, monitor, or track dogs. Each dog may have a different tolerance for and reaction to Dogtra products. Closely observe your dog when determining the right level of stimulation, receiver fit, and other settings of your Dogtra product. Training Methods Dogtra products may be used with a variety of training methods that provide clear and consistent messages to your dog. Fit and Wear Proper fit and wear of your Dogtra product is important for the comfort of your dog as well as the functioning of your product. Dogtra receivers should fit comfortably and not too tightly, so that the receiver stays in place and does not move around your dog’s neck. Do not leave a receiver on your dog for an extended time. Although each dog is different, Dogtra recommends that its receivers be used a maximum of 4 to 6 hours at any one time on your dog. A receiver that is used for overly long periods or that fits improperly may cause skin irritation or sores on your dog’s neck. Regularly check the receiver's contact area on your dog’s skin. If your dog exhibits skin irritation or sores, stop using the Dogtra product and consult with a veterinarian. UNAUTHORIZED USE Dogtra products should be used only in a safe and responsible manner to train, educate, monitor, or track dogs. Dogtra products are not intended for use in any other manner; they are not intended for use with other animals or with humans; and they are not intended for use in unsafe situations or environments that could lead to death, injury, loss or damage. BATTERY Your Dogtra product contains batteries. Do not attempt to replace the battery yourself. Contact Dogtra or your Dogtra retailer to replace your battery. Dispose of batteries as provided by your local regulations. Do not disassemble, crush, heat, or otherwise alter the battery as it may cause fire, explosion, injury and/or property damage. 3 OWNER SAFETY Handling and Repair Dogtra products can be damaged or malfunction if dropped, especially on hard surfaces, or otherwise improperly handled. Do not use a damaged or malfunctioning product as it may cause injury or property damage. If your product is damaged or malfunctions, contact Dogtra to obtain service before using the product. Electrical Product Your Dogtra product contains electrical components and batteries. Do not use or keep your product near heat or flammable sources. Such use or storage may damage your product and/or cause fire, explosion, injury, or property damage. Charging Only charge your Dogtra product with its accompanying Dogtra charger. Do not attempt to charge your product in any other manner or in temperatures less than 32°F (0°C) or over 113°F (45°C) as it may cause fire, explosion, injury, and/or property damage. If you notice damage to your product, its charger, or battery, obtain service from Dogtra before charging the product. Do not use more than one splitter cable with a single battery charger. Medical Device Interference Dogtra products contain electrical and magnetic components that emit low level electromagnetic waves and radio frequencies. These electromagnetic waves or radio frequencies may interfere with pacemakers, defibrillators, or other medical devices. Consult your physician or medical device maker before using your medical device with a Dogtra product. If you think that your Dogtra product is interfering with your pacemaker, defibrillator, or other medical device, stop using the Dogtra product. Aggressive Dogs Do not use Dogtra products with aggressive dogs as such dogs may react adversely and cause injury to people or other dogs. Seek the assistance of a dog-training specialist or veterinarian when dealing with aggressive dogs. Children Dogtra products are not toys. Adult supervision and close attention are necessary when Dogtra products are used by or near children. 4 PACKAGE CONTENTS ........................................................................................... MAIN FEATURES .................................................................................................... OVERVIEW ............................................................................................................... UNDERSTANDING YOUR TRAINING SYSTEM BUTTON FUNCTION ........................................................................................ LED INDICATOR ............................................................................................... GETTING STARTED DOWNLOADING THE PATHFINDER2 APP ............................................... ONLINE WEB MANUAL ................................................................................. PAIRING YOUR DEVICE ................................................................................. KEY FEATURES OF PATHFINDER2 APP .................................................... OTHER FEATURES & DETAILS ........................................................................... DEVICE INFORMATION RECEIVER FITTING .......................................................................................... FINDING THE RIGHT STIMULATION ........................................................... MAXIMIZING THE DISTANCE ........................................................................ PRODUCT MAINTENANCE CHARGING THE PATHFINDER2 .................................................................. REPLACING THE ANTENNA ...........................................…

Text truncated - open the document above for the full version.

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 2023. 06. 07 SUBJECT: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii) Filing for FCC ID: SWN-PT20C To Whom It May Concern: Dogtra Co., Ltd. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Dogtra Co., Ltd. (“the applicant”) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Applicant Signature: Yong Byeong Chae / Associate manager Address: 35, Namdongdong-ro 33beon-gil, Namdong-gu, Incheon 21694 Rep. of KOREA E-mail: [email protected] Tel/Fax: 032-812-2445 / 032-812-2449

Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 TIMCO ENGINEERING INC. TCB & FCB 849 NW State Road 45 FCC Approvals Newberry, Florida 32669 Industry Canada Approvals http://www.timcoengr.com Notified Body for Europe 888.472.2424 F 352.472.2030 email: [email protected] 2023. 06. 07. SUBJECT: UPLOAD FILES TO WEBSITE Product: Pathfinder2 Applicant: Dogtra Co., Ltd. Model: PT20C Address: 35, Namdongdong-ro 33beon-gil, Namdong-gu, Incheon 21694 Rep. of KOREA FCC ID: SWN-PT20C Dear Sir/Madam As appointed agent for Dogtra Co., Ltd., we submit the application to Timco Engineering Inc, for certification of the above product. Please review all files uploaded to Timco web site. If you have any queries, please do not hesitate to contact us Best regards, Kwang-Yeol Choo / Test Engineer e-mail: [email protected]

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 2023. 06. 07. SUBJECT: FCC Application for FCC ID: SWN-PT20C To Whom It May Concern: We, the undersigned, hereby authorize Kwang-Yeol Choo at Kostec Co., Ltd on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Kwang-Yeol Choo at Kostec Co.,Ltd on our behalf shall have the same effect as acts of our own. Sincerely, Yong Byeong Chae / Associate manager Address: 35, Namdongdong-ro 33beon-gil, Namdong-gu, Incheon 21694 Rep. of KOREA Tel/Fax: 032-812-2445 / 032-812-2449

Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Confidentiality Request regarding application for certification of FCC ID: SWN-PT20C Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File name Block diagram Circuit Description Operational Description Part list CONF APPENDIX_PT20C_BLK CONF APPENDIX_PT20C_SCH CONF APPENDIX_PT20C_Operation Description CONF APPENDIX_PT20C_BOM The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 and 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Date: 2023. 06. 07. Yong Byeong Chae / Associate manager Address: 35, Namdongdong-ro 33beon-gil, Namdong-gu, Incheon 21694 Rep. of KOREA Tel/Fax: 032-812-2445 / 032-812-2449

Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 Page: 1 / 4 Appendix 2. Photographs of EUT [External View] [Front] [Rear] Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 Page: 2 / 4 [ Top ] [ Bottom ] Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 Page: 3 / 4 [ Left ] [ Right ] Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 Page: 4 / 4 [ Port ] BLANK DC IN

Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 Page: 1 / 1 Appendix 4. Sample Label & Location Label Information The following is a sample copy of the label that will be placed on back side of the product. The FCC ID is marked in the product label and below information is visible printed on the label. Label location The label shown above shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase. The label is located here.

Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 Page: 1 / 3 Appendix 3. Photographs of EUT [Internal View] [ Inside View ] Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 Page: 2 / 3 [Main board Front] BT Antenna Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 Page: 3 / 3 [Main board Rear]

Report No: KST-FCS-230001(1) KST-FCS-SRS-Rev.0.4 Page: 2 / 56 This report shall not be reproduced except in full without the written approval of KOSTEC Co., Ltd. Table of Contents 1. Statement of Compliance ................................................................................................... 3 1.1 Test Method List ......................................................................................................................... 3 2. Administration Data ............................................................................................................ 4 2.1 Test Laboratory ........................................................................................................................... 4 2.3 Applicant ..................................................................................................................................... 4 2.4 Manufacturer .............................................................................................................................. 4 2.5 Application Details ...................................................................................................................... 4 3. GENERAL INFORMATION ................................................................................................ 6 3.1 Description of DUT ..................................................................................................................... 6 3.2 Test Condition ........................................................................................................................... 10 3.3 Requirements for compliance testing defined by FCC ............................................................. 10 4. Specific Absorption Rate (SAR) ........................................................................................ 11 4.1 Introduction ............................................................................................................................... 11 4.2 SAR Definition .......................................................................................................................... 11 4.3 SAR Measurement Procedure ................................................................................................. 11 5. SAR Measurement System .............................................................................................. 12 5.1 E-field Probe ............................................................................................................................. 13 5.2 Mounting Devices ..................................................................................................................... 14 5.3 DASY6 Robots ......................................................................................................................... 14 5.4 SAM Phantoms......................................................................................................................... 15 5.5 ELI Phantoms ........................................................................................................................... 15 5.6 DAE4 - Data Acquisition Electronics ........................................................................................ 16 5.7 Validation Dipoles ..................................................................................................................... 16 5.8 Test Equipment List .................................................................................................................. 17 6. Measurement Results ...................................................................................................... 18 6.1 Tissue Simulating Liquids ......................................................................................................... 18 6.2 System Verification ................................................................................................................... 19 6.3 DUT Testing Position ................................................................................................................ 21 6.4 SAR measurement procedure .................................................................................................. 21 6.5 SAR Exposure Limits................................................................................................................ 21 6.6 SAR test result.......................................................................................................................... 22 6.7 Simultaneous Transmission SAR Analysis ............................................................................... 23 7. Uncertainty Assessment ................................................................................................... 24 Appendix A : Plot of measured tissue. .................................................................................. 25 Appendix B : Plot of system verification test. ........................................................................ 26 Appendix C : Plot of SAR test. ............................................................................................. 27 Appendix D: DUT setup photos ............................................................................................ 28 Appendix E: System Certificate & calibration ....................................................................... 29 Report No: KST-FCS-230001(1) KST-FCS-SRS-Rev.0.4 Page: 3 / 56 This report shall not be reproduced except in full without the written approval of KOSTEC Co., Ltd. 1. Statement of Compliance The maximum results of Specific Absorption Rate (SAR) found during testing for DUT are as follows. Limb Configuration Mode Freq. Position Measured 10 g SAR (W/kg) Reported 10 g SAR (W/kg) Note FHSS 927.75 Front 2.09 2.55 This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General population/Uncontrolled exposure limits specified in ANSI/IEEE Standards and has been tested in accordance with …

Text truncated - open the document above for the full version.

Report No.: KST-FCR-230002(1) KST-FCR-RFS-Rev.0.5 Page: 2 / 39 This report shall not be reproduced except in full without the written approval of KOSTEC Co., Ltd, Table of Contents 1. GENERAL INFORMATION ............................................................................................................ 3 1.1 Test Facility ............................................................................................................................................... 3 1.2 Location .................................................................................................................................................... 3 1.3 Revision History of test report .................................................................................................................. 4 2. EQUIPMENT DESCRIPTION ........................................................................................................ 5 3. SYSTEM CONFIGURATION FOR TEST ....................................................................................... 6 3.1 Characteristics of equipment .................................................................................................................... 6 3.2 Used peripherals list ................................................................................................................................. 6 3.3 Product Modification ................................................................................................................................. 6 3.4 Operating Mode ........................................................................................................................................ 6 3.5 Test Setup of EUT .................................................................................................................................... 6 3.6 Parameters of Test Software Setting ........................................................................................................ 7 3.7 Table for Test condition ............................................................................................................................. 8 3.8 Used Test Equipment List ......................................................................................................................... 9 4. SUMMARY TEST RESULTS ........................................................................................................ 11 5. MEASUREMENT RESULTS ........................................................................................................ 12 5.1 Peak Output Power ................................................................................................................................ 12 5.2 20 dB Bandwidth .................................................................................................................................... 14 5.3 Channel Separation ................................................................................................................................ 17 5.4 Number of Hopping Channels ................................................................................................................ 20 5.5 Time of Occupancy ................................................................................................................................. 22 5.6 Conducted Spurious Emissions (Band-edge) ........................................................................................ 25 5.7 Spurious RF Radiated emissions ........................................................................................................... 29 5.8 Antenna requirement .............................................................................................................................. 36 5.9 AC Power Conducted emissions ............................................................................................................ 37 Report No.: KST-FCR-230002(1) KST-FCR-RFS-Rev.0.5 Page: 3 / 39 This report shall not be reproduced except in full without the written approval of KOSTEC Co., Ltd, 1. GENERAL INFORMATION 1.1 Test Facility Test laboratory and address KOSTEC Co., Ltd. 28(175-20,Annyeong-dong)406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Telephone Number: 82-31-222-4251 Facsimile Number: 82-31-222-4252 Registration information KOLAS No.: KT232 RRA (National Radio Research Agency): KR0041 FCC Designation No.: KR0041 IC Designation No.: KR0041 VCCI Membership No.: 2005 1.2 Location KOSTEC Co., Ltd. Report No.: KST-FCR-230002(1) KST-FCR-RFS-Rev.0.5 Page: 4 / 39 This report shall not be reproduced except in full without the written approval of KOSTEC Co., Ltd, 1.3 Revision History of test report Rev. Revisions Effect page Reviewed Date - Initial issue All Gyeong Hyeon, Park 2023. 06. 07. 1 Revise family model name 1, 4 Gyeong Hyeon, Park 2023. 06. 29. Report No.: KST-FCR-230002(1) KST-FCR-RFS-Rev.0.5 Page: 5 / 39 This report shall not be reproduced except in full without the written approval of KOSTEC Co., Ltd, 2. EQUIPMENT DESCRIPTION The product specification described herein was declared by manufacturer. And refer to user’s manual for the details. Equipment Name Pathfinder2 Model No PT20C (Family model names: PT 20C, PT-20C, PATHFINDER2 SERIES) Usage Dog training device Serial Number Proto type Modulation technology FHSS Modulation type GFSK Emission Type F1D Maximum output power 29.65 dBm Operated Frequency 915.25 MHz ~ 927.75 MHz Channel Number 51 Operation temperature -20 °C ~ 50 °C Power Source DC 3.7 V Antenna Description Dipole Antenna(RP-SMA), gain : 1 dBi Remark 1. The device was operating at its maximum output power for all measurements. 2. The radiation measurements are performed in X, Y, Z axis positioning. Only the worst case (X) is shown in the report. 3. The above DUT’s information was declared by manufacturer. Please refer to the specifications or user manual for more detailed description. FCC ID SWN-PT20C Report No.: KST-FCR-230002(1) KST-FCR-RFS-Rev.0.5 Page: 6 / 39…

Text truncated - open the document above for the full version.

사양 승인원 (Approval Sheet) TS23-DTR-900 TELLESTAR Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 2/15 TELLESTAR 목 차 (Table of Contents) 1. 승인원 이력 LIST(Approval Sheet Check List) ___________________________________________ 3 2. 개 요(APPLICATION) ___________________________________________________________________ 4 2.1. 개요 ____________________________________________________________________________________________ 4 3. 규 격(Specification) _____________________________________________________________________ 5 3.1. 일반 규격 ______________________________________________________________________________________ 5 3.2. 전기적 규격 ____________________________________________________________________________________ 5 3.3. 기계적 규격 ____________________________________________________________________________________ 5 4. 시험방법 및 절차서(Test Procedure & Measurement) __________________________________ 6 4.1. 외관검사 ________________________________________________________________________________________ 6 4.2. 전기적 특성검사 _______________________________________________________________________________ 6 4.2.1. 준비물 _______________________________________________________________________________________________ 6 4.2.2. 검사방법 _____________________________________________________________________________________________ 6 4.2.2.1. 검사 ____________________________________________________________________________________________ 7 5. 포장 및 운반(Packing, Shipping, Handling) _____________________________________________ 8 5.1. 외관사양 ________________________________________________________________________________________ 8 5.2. 포 장 ________________________________________________________________________________________ 8 6. 외 관(Appearance) _______________________________________________________________________ 9 6.1. Antenna Ass’y _________________________________________________________________________________ 10 7. 시험성적서(Test Data Sheet) _____________________________________________________________ 11 8. Data Sheet ________________________________________________________________________________ 12 8.1. V.S.W.R _______________________________________________________________________________________ 12 8.2. Impedance ____________________________________________________________________________________ 13 8.3. Log Mag _______________________________________________________________________________________ 14 8.4. Data ___________________________________________________________________________________________ 15 Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 3/15 TELLESTAR 1. 승인원 이력 LIST(Approval Sheet Check List) 이 력 변 경 날 짜 항 목 / 내 용 근 거 승인원 issue 제품 issue Ver 1.0 Ver 1.0 2023.05.22 초도발행 Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 4/15 TELLESTAR 2. 개 요(APPLICATION) 2.1. 개요 본 규격서는 TS23-DTR-900 의 사양에 대해 기술하였다. Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 5/15 TELLESTAR 3. 규 격(Specification) 3.1. 일반 규격 General specification Model name TS23-DTR-900 Antenna type Dipole Antenna 3.2. 전기적 규격 Electrical specification Frequency range 900MHz V.S.W.R 1.9 : 1 Max. Gain(dB) 1dBi Radiation pattern Omni-directional Polarization Vertical Max Power(W) 5W Max. Impedance 50  Normalizer 3.3. 기계적 규격 Mechanical specification Connector type RP-SMA(F) Cover material Keyflex Color Black Temperature range -30°C ~ 70°C Weight 12 ± 1g Dimension 도면참조 Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 6/15 TELLESTAR 4. 시험방법 및 절차서(Test Procedure & Measurement) 4.1. 외관검사 Antenna의 외관 및 치수, Connector등이 첨부된 “6 ”번 항의 외관과 일치 하는지를 확인한다. 4.2. 전기적 특성검사 4.2.1. 준비물 장 비 명 Model 수량 규 격 Network Analyzer HP8753D (또는 동등 이상의 장비) 1대 ∙ Freq. Range : 300KHz ~ 3GHz ∙ Accuracy : <5ppm ∙ Dynamic Range : 105dB ∙ Trace at ±200dB ∙ Resolution : 1Hz ∙ Impedance : 50  Adaptor 1EA ∙ N(M)-RP SMA(F) Calibration Kit HP85032B 1Set ∙ DC ~ 3GHz (SMA-Type) 4.2.2. 검사방법 그림 1. Network Analyzer 검사 시 계측기 연결도 PRINTER Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 7/15 TELLESTAR 4.2.2.1. 검사 가. 장비 Setting 및 Calibration ㉠ 장비 Setting ⓐ 주파수대역 : Frequency : Start : 892MHz, Stop : 938.0MHz ⓑ Source Power : 10dBm, ⓒ IF Bandwidth : 1000Hz ⓓ Number of Point : 401 ㉡ Calibration SMA-Type Cal. Kit을 사용하여 O.S.L 방법으로 1 Port Calibration한다. ⓐ S 11 Calibration : Port 1에 Open, Short, Load를 각각 연결하여 Calibration한다. ㉢ Calibration 확인 ⓐ Port1에 Load를 연결하여 S 11 의 V.S.W.R이 1.02 : 1이하 인지를 확인한다. ⓑ Port1에 Load를 연결하여 S 21 값이 – 80.0dB 이하인지를 확인한다. 확인 결과 위의 기준을 만족하지 못할 경우 ㉡항의 Calibration 항을 반복 수행한다. 나. 검사방법 및 내용 항 목 검 사 방 법 기 준 V.S.W.R 위 그림 1과 같이, ANT에 Network Analyzer의 Port 1을 연결한 다음 Operating Band 내에서의 S 11 값을 측정한다. 1.9:1 Max. Impedance 위 그림 1과 같이, ANT에 Network Analyzer의 Port 1을 연결한 다음 Operating Band 내에서의 Smith Chart 상의 S 11 값을 측정한다. 50 ± 20Ω Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 8/15 TELLESTAR 5. 포장 및 운반(Packing, Shipping, Handling) 5.1. 외관사양 가. 주문자의 상호와 생산자의 상호가 명기되어야 한다. 나. Model 명, Serial NO. 및 수량이 명기되어야 한다. 5.2. 포 장 가. 본 제품은 보관 및 수송에 따른 진동, 충격으로부터 안전하게 보호 될 수 있도록 포장한다. Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 9/15 TELLESTAR 6. 외 관(Appearance) No. 도 번 [DWG No.] 품 명 [TITLE] REV. Page 비 고 1 TS23-DTR-900 Rev.IR Antenna Ass`y 1.0 1/1 Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 10/15 TELLESTAR 6.1. Antenna Ass’y Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 11/15 TELLESTAR 7. 시험성적서(Test Data Sheet) Parameter Specification Data 25°C V.S.W.R 1.9: 1 Max. 1.89 Impedance 50 ± 20Ω 48.210 Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 12/15 TELLESTAR 8. Data Sheet 8.1. V.S.W.R Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 13/15 TELLESTAR 8.2. Impedance Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 14/15 TELLESTAR 8.3. Log Mag Date 2023.05.22 Version No. 1.0 Subject TS23-DTR-900 15/15 TELLESTAR 8.4. Data Approval Specification PT20E-BT ANT Data : 2022. 4. 11 Version : 1.0 Table of Contents 1. Approval Check List ....................................................................................................................................................…

Text truncated - open the document above for the full version.

Appendix D: DUT setup photos [FRONT] [REAR] [Left] [Right] [Bottom] BLANK

Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +82-31-222-4252 Page: 1 / 8 Appendix 1. Photographs of test setup Radiated RF measurement (30 MHz ~ 1 GHz)_DSS Head office & Test Lab: 28(175-20,Annyeong-dong) 406-gil sejaro, Hwaseong-si Gyeonggi-do, Korea Tel: +82-31-222-4251 / Fax: +8…

Text truncated - open the document above for the full version.