SZV-PTM215UTemperature and Humidity Sensor with transmitter

© 2020 EnOcean | www.enocean.com PTM 210 / PTM 215 / PTM 210U / PTM 215U / PTM 210J / PTM 215J / User Manual Page 1/45 USER MANUAL PTM 210 / PTM 215 / PTM 215U / PTM 215J DC Step code and later PTM 210 / PTM 215 PTM 215U PTM 215J Pushbutton transmitter modules DC Step code and later The product is protected by the following granted Patents: US7710227, DE10315765B4 US9614553, EP1312171B1, CN100508406C EP1389358B1, JP4225792B2 US7019241, EP1550202B1, DE50303733D1, CN1689218B US7391135, EP1611663B1, DE10315764B4, US8502470, JP5617103B2 EP2524572B1 And also by pending or not yet published Patents and Designs. © 2020 EnOcean | www.enocean.com PTM 210 / PTM 215 / PTM 215U / PTM 215J User Manual August 2020 | Page 2/45 USER MANUAL PTM 210 / PTM 215 / PTM 215U / PTM 215J DC Step code and later REVISION HISTORY The following major modifications and improvements have been made from the first version of this document: No Major Changes 2.0 Update to modules with step code DC. 2.1 Update of certification numbers in US and Japan. Published by EnOcean GmbH, Kolpingring 18a, 82041 Oberhaching, Germany www.enocean.com, [email protected], phone ++49 (89) 6734 6890 © EnOcean GmbH All Rights Reserved Important! This information describes the type of component and shall not be considered as assured characteristics. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the EnOcean website: http://www.enocean.com. As far as patents or other rights of third parties are concerned, liability is only assumed for devices, not for the described applications, processes and circuits. EnOcean does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to workmanship. Devices or sys- tems containing RF components must meet the essential requirements of the local legal au- thorities. The devices must not be used in any relation with equipment that supports, directly or indi- rectly, human health or life or with applications that can result in danger for people, animals or real value. Components of the devices are considered and should be disposed of as hazardous waste. Local government regulations are to be observed. Packing: Please use the recycling operators known to you. By agreement we will take packing material back if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or that we are not obliged to accept, we shall have to invoice you for any costs incurred. © 2020 EnOcean | www.enocean.com PTM 210 / PTM 215 / PTM 215U / PTM 215J User Manual August 2020 | Page 3/45 USER MANUAL PTM 210 / PTM 215 / PTM 215U / PTM 215J DC Step code and later TABLE OF CONTENT 1 GENERAL DESCRIPTION .................................................................................... 5 1.1 Product variant and ordering codes .................................................................... 5 1.2 Basic Functionality ........................................................................................... 6 1.3 Typical Applications .......................................................................................... 8 1.4 Technical Data ............................................................................................... 10 1.5 Mechanical Interface ....................................................................................... 10 1.6 Environmental Conditions ................................................................................ 11 1.7 References .................................................................................................... 11 2 FUNCTIONAL DESCRIPTION ............................................................................. 12 2.1 Block Diagram ............................................................................................... 12 2.2 Contact Nipples assignment ............................................................................. 13 2.3 Available EnOcean Equipment Profiles ............................................................... 13 3 OPERATING MODES ........................................................................................ 15 3.1 Normal mode operation .................................................................................. 15 3.2 Secure mode operation ................................................................................... 15 3.2.1 Implicit RLC – legacy, not recommended........................................................ 17 3.2.2 Explicit RLC – recommended ........................................................................ 17 3.2.3 Security Teach-in ........................................................................................ 17 3.3 Switching between modes ............................................................................... 18 3.4 Factory reset ................................................................................................. 20 4 Radio Communication ..................................................................................... 21 4.1 ERP 1 Communication ..................................................................................... 21 4.1.1 ULP Frames ................................................................................................ 21 4.1.2 Common Frames ......................................................................................... 23 4.2 ERP 2 Communication ..................................................................................... 24 4.2.1 Normal mode Telegram................................................................................ 24 4.2.2 Secure mode Telegram ................................................................................ 24 © 2020 EnOcean | www.enocean.com PTM 210 / PTM 215 / PTM 215U / PTM 215J User Manual August 2020 | Page 4/45 USE…

Text truncated - open the document above for the full version.

EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany Phone +49.89.67 34 689-0 Fax +49.89.67 34 689-50 [email protected] www.enocean.com Managing Directors: Andreas Schneider, Dr. Peter Klein Registered Court Munich HRB 139781 VAT Reg.No. DE813355588 Account: HypoVereinsbank München No. 2440610 Bank Code 700 202 70 EnOcean GmbH Kolpingring 18a 82041 Oberhaching/Germany Armin Anders VP Business Development Phone +49 89 6734689-33 [email protected] Authority to Act as Agent FCC SUBJECT: FCC Application for “FCC ID: SZV-PTM215U” To Whom It May Concern: We, the undersigned, hereby authorize Jason Stewart of VPI Laboratories at 313 W. 12800 S,. Suite 311, Draper UT 84020 to act as our agent and on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by VPI Laboratories on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Armin Anders FEDERAL COMMUNICATIONS COMMISSION 7435 Oakland Mills Road Columbia, MD 21046 U.S.A. Date: January 22 nd , 2021

EnOcean GmbH | Kolpingring 18a | 82041 Oberhaching | Germany Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 U.S.A. FCC Confidentiality Request To Whom It May Concern: Pursuant to paragraphs 0.457(d) and 0.459 of the Commission’s rules (47 C.F.R.) and section 552(b)(4) of the Freedom of Information Act, EnOcean GmbH requests confidentiality for the following product(s): Applicant: EnOcean GmbH Model: PTM 215U FCC ID: SZV-PTM215U For the product(s) stated above, we request that the following information be held confidential. 1. Schematics 2. Block Diagram 3. Operational Description The above exhibits contain EnOcean GmbH trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our product. This material is not customarily available to the general public and we request that it be withheld from public inspection. If you have any questions, please feel free to contact me. Sincerely, Armin Anders VP Business Development EnOcean GmbH Kolpingring 18a 82041 Oberhaching Germany www.EnOcean.com [email protected] Armin Anders VP Business Development T +49.89. 67 34 689 – 33 F +49 89. 67 34 689 – 55 [email protected] Date 25. Jan. 2021 Managing Directors Andreas Schneider, Dr. Peter Klein Registered Court Munich HRB 139781 VAT Reg.No. DE813355588 Account HypoVereinsbank München IBAN DE19700202700002440610 BIC HYVEDEMMXXX

313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_ExtPho.docx Page 1 of 3 PROPRIETARY External Photographs Photograph 1 – Front View of the EUT Photograph 2 – Top/Left View 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_ExtPho.docx Page 2 of 3 PROPRIETARY Photograph 3 – Back View of the EUT Photograph 4 – Bottom/Right View 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_ExtPho.docx Page 3 of 3 PROPRIETARY Photograph 5 – PCB Placement Inside EUT

LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 1 von 5 1. General Current Step Code version und state is defined in: “C71-PTM_215U_NEXT_Cover_sheet_manufacturing_data.docx” 2. Laser marking PCB assembler lasers bottom side of the PCB (in yellow rectangle) as shown below: Figure 1. Area for the laser markings on the bottom side of the PCB Only DMC code should be lasered on the PCB, all the rest of the content will be part of the label placed on the plastic housing (Figure 2). Table 1. Content of the PCB markings Field Content Description 1 DMC Data Matrix Code LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 2 von 5 3. Label on the PTM module housing Material des Klebeschild entsprechend „KV0001x- Absatz 5.1. Material und Beständigkeit“ Aufkleber 27x16 weiß PE, Katek Artikel-Nr.: 93100394BF Figure 2. PTM 215U label example. Figure 3. Positions of the elements with the defined dimensions in mm. 27 mm 16 mm LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 3 von 5 Label Position on the device LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 4 von 5 FCC ID & IC Number to be used: FCC ID: SZV-PTM215U IC: 5713A-PTM215U Format of the elements: All the information in the label has to be written in the bold font! (1) Arial Bold 3,5 Width 84% (this is like Arial Narrow) (2) Arial Bold 3,0 Width 84% (this is like Arial Narrow) - FCC Mark; Height 5 mm - ID font and size: Arial Bold 3,5 Width 100% - EnOcean Alliance Logo: (from .jpg file, 6.3 mm x 3.8 mm) - EnOcean name: (from .jpg file, size 7.9 mm x 1.5 mm). QR-Code Version: 5 (37x37 pixel) QR-Code Type: Model 2 Error Correction Level: M (15% error correction) Mode: Alphanumeric Mode Character Capacity: 122 Free space around the code: 1 mm in all directions Size of the QR-Code: 6.26 mm x 6.26 mm Label shown in Figure 3 among other information contains a QR code with the following data: Table 2. QR code content Identifier Length of data Value 30S 15 characters (12 data) Static Source Address (hex), 0x0000 + EnOcean Radio ID e.g. 000001500100 + 1 character Field Separator 13Z 35 characters (32 data) Security AES key (16 Bytes), generated and specific for each device e.g. 12345678123456781234567812345678 + 1 character Field Separator LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 5 von 5 30S000001500100+13Z12345678123456781234567812345678 +1P000B00000055+30PS3051-A215+2PDC22+S01123456789012 Figure 4. QR code content example based on the above table 4. Label for packaging The label should be based on labeling requirement document: „Etikett für Verpackung_KV0001x”. Specific guidelines on the content: Table 3. Packaging label content Field 05 - Product name: PTM 215U Field 06 - Revision (Step Code): Check Manufacturing cover sheet: “C71-PTM_215U_NEXT_Cover_sheet_manufacturing_data.docx” Field 07 - Order code: S3051-A215 Field 08 - State code: Check Manufacturing cover sheet: “C71-PTM_215U_NEXT_Cover_sheet_manufacturing_data.docx” Field 10 - Quantity: Check Manufacturing cover sheet:: “C71-PTM_215U_NEXT_Cover_sheet_manufacturing_data.docx” 1P 14 characters (12 data) Product ID (EnOcean Alliance), e.g. 000B00000055 + 1 character Field Separator 30P 13 characters (10 data) Ordering Code (EnOcean module), e.g. S3051-A215 + 1 character Field Separator 2P 6 characters (4 data) Step Code - Revision (EnOcean module), e.g. DC22 + 1 character Field Separator S 15 characters (2 + 12 data) Manufacturer recognition, 01 + DMC/Serial Number, e.g. 123456789012 Total: 103 characters

LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 1 von 5 1. General Current Step Code version und state is defined in: “C71-PTM_215U_NEXT_Cover_sheet_manufacturing_data.docx” 2. Laser marking PCB assembler lasers bottom side of the PCB (in yellow rectangle) as shown below: Figure 1. Area for the laser markings on the bottom side of the PCB Only DMC code should be lasered on the PCB, all the rest of the content will be part of the label placed on the plastic housing (Figure 2). Table 1. Content of the PCB markings Field Content Description 1 DMC Data Matrix Code LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 2 von 5 3. Label on the PTM module housing Material des Klebeschild entsprechend „KV0001x- Absatz 5.1. Material und Beständigkeit“ Aufkleber 27x16 weiß PE, Katek Artikel-Nr.: 93100394BF Figure 2. PTM 215U label example. Figure 3. Positions of the elements with the defined dimensions in mm. 27 mm 16 mm LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 3 von 5 Label Position on the device LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 4 von 5 FCC ID & IC Number to be used: FCC ID: SZV-PTM215U IC: 5713A-PTM215U Format of the elements: All the information in the label has to be written in the bold font! (1) Arial Bold 3,5 Width 84% (this is like Arial Narrow) (2) Arial Bold 3,0 Width 84% (this is like Arial Narrow) - FCC Mark; Height 5 mm - ID font and size: Arial Bold 3,5 Width 100% - EnOcean Alliance Logo: (from .jpg file, 6.3 mm x 3.8 mm) - EnOcean name: (from .jpg file, size 7.9 mm x 1.5 mm). QR-Code Version: 5 (37x37 pixel) QR-Code Type: Model 2 Error Correction Level: M (15% error correction) Mode: Alphanumeric Mode Character Capacity: 122 Free space around the code: 1 mm in all directions Size of the QR-Code: 6.26 mm x 6.26 mm Label shown in Figure 3 among other information contains a QR code with the following data: Table 2. QR code content Identifier Length of data Value 30S 15 characters (12 data) Static Source Address (hex), 0x0000 + EnOcean Radio ID e.g. 000001500100 + 1 character Field Separator 13Z 35 characters (32 data) Security AES key (16 Bytes), generated and specific for each device e.g. 12345678123456781234567812345678 + 1 character Field Separator LABELING REQUIREMENTS Valid from: Creator: C71 – KV01 Revision: 3 03.02.2021 D. Draksas PTM 215U Die in diesem Dokument enthaltenen Informationen sind Eigentum der EnOcean GmbH und als solche vertraulich zu behandeln. Ausnahmen bedürfen der Genehmigung durch autorisierte Mitarbeiter. Kopien dieses Dokumentes, die den anerkannten Verteilungssystemen entnommen wurden, sind unkontrollierte Dokumente, deren Anwendung jegliche Haftung ausschließt. Seite 5 von 5 30S000001500100+13Z12345678123456781234567812345678 +1P000B00000055+30PS3051-A215+2PDC22+S01123456789012 Figure 4. QR code content example based on the above table 4. Label for packaging The label should be based on labeling requirement document: „Etikett für Verpackung_KV0001x”. Specific guidelines on the content: Table 3. Packaging label content Field 05 - Product name: PTM 215U Field 06 - Revision (Step Code): Check Manufacturing cover sheet: “C71-PTM_215U_NEXT_Cover_sheet_manufacturing_data.docx” Field 07 - Order code: S3051-A215 Field 08 - State code: Check Manufacturing cover sheet: “C71-PTM_215U_NEXT_Cover_sheet_manufacturing_data.docx” Field 10 - Quantity: Check Manufacturing cover sheet:: “C71-PTM_215U_NEXT_Cover_sheet_manufacturing_data.docx” 1P 14 characters (12 data) Product ID (EnOcean Alliance), e.g. 000B00000055 + 1 character Field Separator 30P 13 characters (10 data) Ordering Code (EnOcean module), e.g. S3051-A215 + 1 character Field Separator 2P 6 characters (4 data) Step Code - Revision (EnOcean module), e.g. DC22 + 1 character Field Separator S 15 characters (2 + 12 data) Manufacturer recognition, 01 + DMC/Serial Number, e.g. 123456789012 Total: 103 characters

313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_IntPho.docx Page 1 of 3 PROPRIETARY Internal Photographs Photograph 1 – Front View of the Device Trace Antenna 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_IntPho.docx Page 2 of 3 PROPRIETARY Photograph 2 – Back View of the Device 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_IntPho.docx Page 3 of 3 PROPRIETARY Photograph 3 – PCB Placement into Housing

313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM_215U_MPE.docx Page 1 of 1 PROPRIETARY 47 C.F.R. Part 1, Subpart I, Section 1.1310 47 C.F.R. Part 2, Subpart J, Section 2.1091 Maximum Permissible Exposure Calculations FCC ID: SZV-PTM215U EUT Device Category = General Population/Uncontrolled Exposure EUT consists of one ISM band radio transmitting operating at a frequency of: 902.875 MHz MPE Summary: According subpart 1.1307 (b)(1) and 2.1091 systems operating under the provisions of this section shall be operated in a manner that ensures the public is not exposed to RF energy level in excess of the communication guidelines. Limits for General Population/Uncontrolled Exposure Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm2) Averaging Time (Minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f2) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density Calculated Formulary: Predication of MPE limit at a given distance S = power density (in appropriate units, e.g. mW/cm 2 ) R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) PG = EIRP MPE and Limit are calculated as follows: f (MHz) Field Strength (dBuV/m) EIRP (mW) Power Density (mW/cm^2) Limit (mW/cm^2) ∆ 902.875 74.6 0.009 0.000002 0.6 0.599998 Result: The device meets FCC MPE limit at 20 cm for General Population/Uncontrolled Exposure as specified in 47 CRF §1.1310 and §2.1091.

313 West 12800 South, Suite 311 Draper, UT 84020 (801) 260-4040 Test Report Certification FCC ID SZV-PTM215U Equipment Under Test PTM 215U Test Report Serial No V053398_03 Date of Test August 5, 2020 Report Issue Date August 6, 2020 Test Specifications: Applicant: FCC Part 15, Subpart C EnOcean GmbH Kolpingring 18A Oberhaching 82041 Germany 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 V053398_03_PTM_215U_FCC_C.docx Page 2 of 31 PROPRIETARY Certification of Engineering Report This report has been prepared by VPI Laboratories, Inc. to document compliance of the device described below with the requirements of Federal Communications Commission (FCC) Part 15, Subpart C. This report may be reproduced in full. Partial reproduction of this report may only be made with the written consent of the laboratory. The results in this report apply only to the sample tested. Applicant EnOcean GmbH Manufacturer EnOcean GmbH Brand Name EnOcean Model Number PTM 215U FCC ID SZV-PTM215U On this 6 th day of July 2020, I, individually and for VPI Laboratories, Inc., certify that the statements made in this engineering report are true, complete, and correct to the best of my knowledge, and are made in good faith. Although NVLAP has accredited the VPI Laboratories, Inc. EMC testing facilities, this report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. VPI Laboratories, Inc. Tested by: Norman P. Hansen Reviewed by: Benjamin N. Antczak 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 V053398_03_PTM_215U_FCC_C.docx Page 3 of 31 PROPRIETARY Revision History Revision Description Date 01 Original Report Release August 6, 2020 02 Corrected the model number September 8, 2020 03 Corrected Lab Accreditation Date February 5, 2021 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 V053398_03_PTM_215U_FCC_C.docx Page 4 of 31 PROPRIETARY Table of Contents 1 Client Information ................................................................................................................................. 5 1.1 Applicant ....................................................................................................................................... 5 1.2 Manufacturer ................................................................................................................................. 5 2 Equipment Under Test (EUT) ............................................................................................................... 6 2.1 Identification of EUT .................................................................................................................... 6 2.2 Description of EUT ....................................................................................................................... 6 2.3 EUT and Support Equipment ........................................................................................................ 6 2.4 Interface Ports on EUT ................................................................................................................. 6 2.5 Modification Incorporated/Special Accessories on EUT .............................................................. 6 2.6 Deviation from Test Standard ....................................................................................................... 6 3 Test Specification, Methods and Procedures ........................................................................................ 7 3.1 Test Specification .......................................................................................................................... 7 3.2 Methods & Procedures .................................................................................................................. 7 3.3 Test Procedure ............................................................................................................................ 10 4 Operation of EUT During Testing ...................................................................................................... 11 4.1 Operating Environment ............................................................................................................... 11 4.2 Operating Modes ......................................................................................................................... 11 4.3 EUT Exercise Software ............................................................................................................... 11 5 Summary of Test Results .................................................................................................................... 12 5.1 FCC Part 15, Subpart C .............................................................................................................. 12 5.2 Result .......................................................................................................................................... 12 6 Measurements, Examinations and Derived Results ............................................................................ 13 6.1 General Comments ...................................................................................................................... 13 6.2 Test Results ................................................................................................................................. 13 6.3 Sample Field Strength Calculation ............................................................................................. 19 7 Test Procedures and Test Equipment .................................................................................................. 21 7.1 Radiated Emissions ..................................................................................................................... 21 7.2 Equipment Calibration ................................................................................................................ 22 7.3 Measurement Uncerta…

Text truncated - open the document above for the full version.

313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_Tsup.docx Page 1 of 6 PROPRIETARY Test Set Up Photographs Radiated Photograph 1: Front View Radiated Emissions, Below 1000 MHz Worst Case Configuration Photograph 2: Back View Radiated Emissions, Below 1000 MHz Worst Case Configuration 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_Tsup.docx Page 2 of 6 PROPRIETARY Photograph 3: Front View Radiated Emissions Worst Case – Above 1000 MHz Configuration Photograph 4: Back View Radiated Emissions Worst Case – Above 1000 MHz Configuration 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_Tsup.docx Page 3 of 6 PROPRIETARY Photograph 5: Vertical Configuration Photograph 6: Flat Configuration 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_Tsup.docx Page 4 of 6 PROPRIETARY Photograph 7: On Edge Configuration 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_Tsup.docx Page 5 of 6 PROPRIETARY Reference Test Set Up Photographs Photograph 8: Reference Photo of Test Setup for Emissions Below 30 MHz Photograph 9: Reference Photo of Test Setup for Emissions From 30 MHz to 1000 MHz 313 West 12800 South, Suite 311, Draper, UT 84020 • (801) 260-4040 PTM215U_Tsup.docx Page 6 of 6 PROPRIETARY Photograph 10: Reference Photo of Test Setup for Emissions Above 1000 MHz