T45171090WUS Moto Gen 3 4x4

LDL Technology S.A.S. : Société par Actions Simplifiée au capital de 506 720 € Siège social : Parc Technologique du Canal- 3 rue Giotto – 31520 Ramonville Saint Agne – RCS Toulouse 477 592 794 – Siret 477 592 794 000 36 – APE 7112 B – N° TVA Intracommunautaire : FR27 477 592 794 LID Technologies S.A.S. Parc technologique du Canal, 3 rue Giotto 31520 Ramonville-Saint-Agne, FRANCE +33 5 34 50 40 92 September 4, 2023 Federal Communications Commission 445 12th St., SW Washington, DC 20554 Industry Canada 3701 Carling Ave., Building 94, Ottawa, ON, K2H 8S2 Subject: User Manual for model 171090 Ref: FCC ID : T45171090 IC ID : 6450A-171090 Dear Sirs: The Wus moto gen 3 4x4 is a part of a Tire Pressure Monitoring System for vehicles, and is supplied as an automotive original equipment. Therefore, no instruction manual is issued for our model 171090. As the product is only useful once installed in a vehicle, we hereby confirm that we will request from the vehicle manufacturer that the enclosed notices are added to the vehicle manual, meeting the requirements of the Federal Communications Commission CFR 47, §15.21, §15.19(a)(3) and Industry Canada RSS-210, §5.11. Sincerely, Philippe Lefaure President and CEO Enclosure: Regulatory notices LDL Technology S.A.S. : Société par Actions Simplifiée au capital de 506 720 € Siège social : Parc Technologique du Canal- 3 rue Giotto – 31520 Ramonville Saint Agne – RCS Toulouse 477 592 794 – Siret 477 592 794 000 36 – APE 7112 B – N° TVA Intracommunautaire : FR27 477 592 794 REGULATORY NOTICES 1) FCC Interference Statement (Part 15.105 (b)) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 2) FCC Part 15 Clause 15.21 [ Do not Modify warning ]: “Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment” 3) FCC Part 15.19(a) [interference compliance statement], unless the following statement is already provided on the device label:- “This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” 4) ISED RSS-Gen Notice (in English and French): “This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.” “L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : L’appareil ne doit pas produire de brouillage; L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.” 5) ISED Canada ICES-003 Compliance Label (CAN BE PROVIDED ON LABEL OR in MANUAL): “CAN ICES-3 (B)/NMB-3(B)”

Trade Register Munich HRB 85742 VAT ID No. DE129484267 Information pursuant to Section 2(1) DL-InfoV (Germany) at www.tuev-sued.com/im print Managing Directors: Walter Reithmaier (CEO) Patrick van Welij Phone: +49 (0) 9421 55 22-0 Fax: +49 (0) 9421 55 22-99 www.tuev-sued.de TÜV SÜD Product Service GmbH Äußere Frühlingstraße 45 94315 Straubing Germany TÜV SÜD Product Service RESPONSIBLE FOR NAME DATE SIGNATURE Project Management Alex Fink 2023-07-24 SIGN-ID 815464 Authorised Signatory Matthias Stumpe 2023-07-24 SIGN-ID 815480 Signatures in this approval box have checked this document in line with the requirements of TÜV SÜD Product Service document control rules. ENGINEERING STATEMENT The measurements shown in this report were made in accordance with the procedures described on test pages. All reported testing was carried out on a sample equipment to demonstrate limited compliance with FCC 47 CFR Part 1.1310, Part 2.1093 and RSS 102 Issue 5 (March 2015) + Amendment 1 (February 2021). The sample tested was found to comply with the requirements defined in the applied rules. RESPONSIBLE FOR NAME DATE Testing Alex Fink 2023-07-24 SIGN-ID 815464 Laboratory Accreditation DAkkS Reg. No. D-PL-11321-11-03 DAkkS Reg. No. D-PL-11321-11-04 Laboratory recognition Registration No. BNetzA-CAB-16/21-15 ISED Canada test site registration 3050A-2 EXECUTIVE SUMMARY A sample of this product was tested and found to be compliant with FCC 47 CFR Part 1.1310, Part 2.1093 and RSS 102 Issue 5 (March 2015) + Amendment 1 (February 2021) Report on the FCC and IC Testing of the LID Technologies WUS MOTO GEN3 4x4 Model: 171090 In accordance with FCC 47 CFR Part 1.1310, Part 2.1093 and RSS-102 Prepared for: LID Technologies Parc Technologique du Canal 3 rue Giotto 31520 Ramonville-Saint-Agne France FCC ID: T45171090 IC: 6450A-171090 COMMERCIAL-IN-CONFIDENCE Date: 2023-07-24 Document Number: TR-713294441-06 | Revision: 1 DISCLAIMER AND COPYRIGHT This non-binding report has been prepared by TÜV SÜD Product Service with all reasonable skill and care. The document is confidential to the potential Client and TÜV SÜD Product Service. No part of this document may be reproduced without the prior written approval of TÜV SÜD Product Service. © 2023 TÜV SÜD Product Service. ACCREDITATION Our BNetzA Accreditation does not cover opinions and interpretations and any expressed are outside the scope of our BNetzA Accreditation. Document Number: TR-713294441-06 | Revision: 1 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 1 of 9 Contents 1 Report Summary .........................................................................................................................2 1.1 Report Modification Record ...........................................................................................................2 1.2 Introduction ....................................................................................................................................2 1.3 Brief Summary of Results .............................................................................................................3 1.4 EUT Modification Record ..............................................................................................................4 1.5 Test Location .................................................................................................................................4 2 Test Details ..................................................................................................................................5 3 Measurement Uncertainty ..........................................................................................................6 Document Number: TR-713294441-06 | Revision: 1 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 2 of 9 1 Report Summary 1.1 Report Modification Record Alterations and additions to this report will be issued to the holders of each copy in the form of a complete document. Revision Description of Change Date of Issue 0 First Issue 2023-05-22 1 Model number corrected from “17109” to “171090” 2023-07-24 Table 1 1.2 Introduction Applicant LID Technologies Manufacturer LID Technologies Model Number(s) 171090 Serial Number(s) N/A Hardware Version(s) 321-093-1090-B Software Version(s) 421234014021 Number of Samples Tested 1 Test Specification/Issue/Date FCC 47 CFR Part 1.1310 and Part 2.1093 RSS 102 Issue 5 (March 2015) + Amendment 1 (February 2021) Test Plan/Issue/Date NA Order Number Date CD-220553 2022-07-22 Date of Receipt of EUT 2023-02-20 Start of Test 2023-03-07 Finish of Test 2023-04-27 Name of Engineer(s) Patrick Müller Related Document(s) KDB 447498 D01 General RF Exposure Guidance v07 ANSI C63.10 (2013) Document Number: TR-713294441-06 | Revision: 1 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 3 of 9 1.3 Brief Summary of Results A brief summary of the tests carried out in accordance with FCC 47 CFR Part 1.1310, Part 2.1093 and RSS-102 is shown below. Section Specification Clause Test Description Result Comments/Base Standard Configuration and Mode: Continuously transmitting with modulation 2.1 1.1310 2.5.1, 2.5.2, 3 RF Exposure Evaluation Pass KDB 447498 D01 v07 Table 2 Document Number: TR-713294441-06 | Revision: 1 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 4 of 9 1.4 EUT Modification Record The table below details modifications made to the EUT during the test programme. The modifications incorporated during each test are recorded on the appropriate test pages. Modification State Description of Modification still fitted to EUT Modification Fitted By Date Modification Fitted 0 As supplied by the customer (S/N: N/A) Not Applicable Not Applicable Table 3 1.5 Test Location TÜV SÜD Product Service conducted the following tests at our Straubing Test Laboratory. Test Name Name of Engineer(s) Configuration and Mode: Transmitting continuously with modulation - 12 V DC power supply RF Exposure Evaluation Alex Fink Table 4 Office Address: Äußere Frühlingstra…

Text truncated - open the document above for the full version.

Trade Register Munich HRB 85742 VAT ID No. DE129484267 Information pursuant to Section 2(1) DL-InfoV (Germany) at www.tuvsud.com/imprint Managing Directors: Walter Reitmaier (Sprecher / CEO) Patrick van Welij Phone: +49 (0) 9421 56 82-0 Fax: +49 (0) 9421 56 82-199 www.tuvsud.com TÜV SÜD Product Service GmbH Äußere Frühlingstraße 45 94315 Straubing Germany TÜV SÜD Product Service Report on the FCC and IC Testing of the LID Technologies WUS MOTO GEN3 4x4 Model: 171090 In accordance with FCC 47 CFR Part 15 C and ISED RSS-210 and ISED RSS-GEN Prepared for: LID Technologies Parc Technologique du Canal 3 rue Giotto 31520 Ramonville-Saint-Agne France FCC ID: T45171090 IC: 6450A-171090 COMMERCIAL-IN-CONFIDENCE Date: 2023-10-04 Document Number: TR-713294441-05 | Revision: 2 RESPONSIBLE FOR NAME DATE SIGNATURE Project Management Alex Fink 2023-10-04 SIGN-ID 837609 Authorised Signatory Matthias Stumpe 2023-10-04 SIGN-ID 837650 Signatures in this approval box have checked this document in line with the requirements of TÜV SÜD Product Service document control rules. Engineering Statement: This measurement shown in this report were made in accordance with the procedures described on test pages. All reporded testing was carried out on a sample equipment to demonstrate limited compilance with with FCC 47 CFR Part 15 C and ISED RSS-210 and RSS-GEN. The sample tested was found to comply with the requirements defined in the applied rules. RESPONSIBLE FOR NAME DATE SIGNATURE Testing Alex Fink 2023-10-04 SIGN-ID 837609 Laboratory Accreditation DAkkS Reg. No. D-PL-11321-11-03 DAkkS Reg. No. D-PL-11321-11-04 Laboratory recognition Registration No. BNetzA-CAB-16/21-15 Industry Canada test site registration 3050A-2 Executive Statement: A sample of this product was tested and found to be compliant with FCC 47 CFR Part 15 C:2021 and ISED RSS210:2020 and RSS-GEN:2019 DISCLAIMER AND COPYRIGHT This non-binding report has been prepared by TÜV SÜD Product Service with all reasonable skill and care. The document is confidential to the potential Client and TÜV SÜD Product Service. No part of this document may be reproduced without the prior written approval of TÜV SÜD Product Service. © 2023 TÜV SÜD Product Service. ACCREDITATION Our BNetzA Accreditation does not cover opinions and interpretations and any expressed are outside the scope of our BNetzA Accredita- tion. Results of tests not covered by our BNetzA Accreditation Schedule are marked NBA (Not BNetzA Accredited). Document Number: TR-713294441-05 | Revision 2 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 1 of 26 Content 1 Report Summary .......................................................................................................................... 2 1.1 Modification Report ............................................................................................................... 2 1.2 Introduction ........................................................................................................................... 2 1.3 Brief Summary of Results ..................................................................................................... 3 1.4 Product Information .............................................................................................................. 1 1.5 EUT Modifications Record .................................................................................................... 1 1.6 Test Location ........................................................................................................................ 1 2 Test Details .................................................................................................................................. 2 2.1 Bandwidth of Momentary Signals.......................................................................................... 2 2.2 Periodic Operation Requirement ........................................................................................... 5 2.3 Temperature Stability............................................................................................................ 9 2.4 Radiated emissions ............................................................................................................ 12 3 Measurement Uncertainty .......................................................................................................... 25 Annex: Photographs 2 pages Document Number: TR-713294441-05 | Revision 2 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 2 of 26 1 Report Summary 1.1 Modification Report Alternations and additions of this report will be issued to the holders of each copy in the form of a com- plete document. Issue Description of changes Date of Issue 0 First Issue 2023-05-22 1 Model number corrected from “17109” to “171090” 2023-07-24 2 Section 2.2, Spectrum analyser screenshot added for alarm mode 2023-10-04 Table 1: Report of Modifications 1.2 Introduction Applicant LID Technologies Manufacturer LID Technologies Model Number(s) 171090 Serial Number(s) N/A Hardware Version(s) 321-093-1090-B Software Version(s) 421234014021 Number of Samples Tested 1 Test Specification(s) / Issue / Date FCC 47 CFR Part 15 C : 2019 ISED RSS-210, Issue 10, Amendment 1 : 2020 ISED RSS-GEN, Issue 5, Amendment 1 : 2019 Test Plan/Issue/Date --- Order Number Date CD-220553 2022-07-22 Date of Receipt of EUT 2023-02-20 Start of Test 2023-03-07 Finish of Test 2023-04-27 Name of Engineer(s) Patrick Müller Related Document(s) ANSI C63.4: 2014 ANSI C63.10: 2013 FCC 47 CFR Part 2 J : 2019 KDB 558074 D01 V05R02 ISED RSS-102, Issue 5, 2015 Document Number: TR-713294441-05 | Revision 2 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 3 of 26 1.3 Brief Summary of Results A brief summary of the tests carried out in accordance with FCC 47 CFR Part 15 C, ISED RSS-210 and ISED RSS-GEN is shown below. Section Specification Clause Test Description Result --- 15.203 Antenna requirement --- 2.1 15.231(c) Bandwidth of momentary signals Pass 2.2…

Text truncated - open the document above for the full version.

Document Number: Annex to TR-713294441-05 | Revision: 0 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 1 of 2 Annex to Test Report TR-713294441-05 | Revision: 0 1 Photographs Taken During Testing 1.1 Test setup for radiated emission measurement (alternate test site) Document Number: Annex to TR-713294441-05 | Revision: 0 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 2 of 2 1.2 Test setup for radiated emission measurement (fully anechoic room)