T5U-ZM108ZigBee 2.4GHz Module (1T1R)

Design Specification Model No.: ZM108 Model name: ZM108 IEEE 802.15.4 RF4CE ZigBee transceiver module Version: v0.1 Date: July 15, 2010 Quanta Microsystems, Inc. Te l： +886-3-3979000 Fax：+886-3-397990 5F, No.188, We n H w a 2nd RdKuei Shan Hsiang, Taoyuan Shien, 333,Taiwan U.S. Regulatory Wireless Notice Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end- product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: T5U-ZM108”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Contents 1. Revision History ............................................................................................................... 3 2. Overview ........................................................................................................................... 4 2.1. Scope...................................................................................................................... 4 2.2. Features .................................................................................................................. 4 2.3. Specification .......................................................................................................... 5 2.4. Mechanical Characteristics .................................................................................... 6 2.5. Interface definition................................................................................................. 7 2.6. RoHS Compliant .................................................................................................... 8 2.7. EMI EMC certifications......................................................................................... 8 Page 2 1. Revision History Date Release Author Description Jul 15, 2010 0.1 Jack Ong First release Page 3 2. Overview 2.1. Scope This document describes the specifications of ZM108 IEEE 802.15.4 transceivers module. The low power consumption and smaller size are suitable for consumer electronic. ZM108 also provides a cost-effective solution for short-range data links and networks. 2.2. Features Extremely low cost Ease of implementation Reliable data transfer Short range operation Very low power consumption Appropriate levels of security Can be used globally Page 4 2.3. Specification Absolute Maximum Ratings …

Text truncated - open the document above for the full version.

188 Wenhwa 2nd Rd.,Kueishan Hsiang Taoyuan Shien 333,Taiwan ,R.O.C. TEL: 886-3-3979000 ; FAX: 886-3-3979906 Date: 01/03/2011 FCC ID: T5U-ZM108 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, ___________________________ Andrew Wang / Manager Quanta Microsystems, Inc. Tel : 886- 3-3979000 Fax : 886-3-3979906 e-mail : [email protected]

188 Wenhwa 2nd Rd.,Kueishan Hsiang Taoyuan Shien 333,Taiwan ,R.O.C. TEL: 886-3-3979000 ; FAX: 886-3-3979906 Agency Authorization Letter Date: 01/03/2011 To whom it may concern: We, the undersigned, Quanta Microsystems, Inc., hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch of Taiwan to act on our behalf, as our agent, in the following matters related to the FCC approval of our products: report submittal, related correspondence, the signing of all documents relating to these matters, and any other lawful activity necessary to obtain such certification. Any act carried out by BVCPS within the scope of this authorization shall have the same effects as our own. This authorization shall expire six months from the original date. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, __________________________________________ Andrew Wang / Manager Quanta Microsystems, Inc. Tel : 886- 3-3979000 Fax : 886-3-3979906 e-mail : [email protected]

FCC ID: T5U-ZM108 Report No.: RF991230C02 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Jan. 04, 2010 Dear Application Examiner, Quanta Microsystems, Inc., It’s a Zigbee 2.4GHz Module (1T1R). FCC ID: T5U-ZM108 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip CC2533. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is CC2533. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: T5U-ZM108 Report No.: RF991230C02 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Gary Chang Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Page: 1

Page: 2

FCC ID: T5U-ZM108 Report No.: RF991230C02 Operational Description This device is a Zigbee 2.4GHz Module (1T1R) with built-in a Zigbee module. This device is a Zigbee 2.4GHz Module (1T1R), which operates in the 2.4GHz frequency spectrum with throughput of up to 250kbps which OQPSK technique will be applied. The transmitter of the EUT is powered by host equipment. The antenna used in this product is PIFA antenna. The other instruction, please have a look at the users manual.

Report No: SA991230C02 1 Report Format Version 4.0.0 RF EXPOSURE REPORT REPORT NO.: SA991230C02 MODEL NO.: ZM108 FCC ID: T5U-ZM108 ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT : Quanta Microsystems, Inc. ADDRESS : 188 Wenhwa 2nd Rd.,Kueishan Hsiang Taoyuan Shien 333,Taiwan ,R.O.C. ISSUED BY : Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS : No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien, 244 Taiwan Report No: SA991230C02 2 Report Format Version 4.0.0 Conclusion No Evaluation Required if power is below this threshold: F(GHz) mW Low 2.405 High 2.480 24.59 Maximum measured transmitter power: Pout (dBm) Pout (mW) Conducted Power 3.4 2.2 EIRP Power 8.7 7.4 *Note: The antenna is PIFA antenna with 5.3dBi gain Threshold for no SAR evaluation is 24.59mW Transmitter power is 7.4mW Conclusion: No SAR evaluation required since Transmitter Pout is below FCC threshold ---END---

Report No.: RF991230C02 1 Report Format Version 4.0.0 FCC TEST REPORT REPORT NO.: RF991230C02 MODEL NO.: ZM108 FCC ID: T5U-ZM108 RECEIVED: Dec. 30, 2010 TESTED: Dec. 30, 2010 ISSUED: Jan. 4, 2011 APPLICANT: Quanta Microsystems, Inc. ADDRESS: 188 Wenhwa 2nd Rd.,Kueishan Hsiang Taoyuan Shien 333,Taiwan ,R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB LOCATION: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien, 244 Taiwan This test report consists of 44 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF991230C02 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD..................................................................................4 1. CERTIFICATION..........................................................................................5 2. SUMMARY OF TEST RESULTS.................................................................6 2.1 MEASUREMENT UNCERTAINTY...............................................................6 3. GENERAL INFORMATION..........................................................................7 3.1 GENERAL DESCRIPTION OF EUT............................................................7 3.2 DESCRIPTION OF TEST MODES..............................................................8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST..........................................8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL...............9 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS............................11 3.4 DESCRIPTION OF SUPPORT UNITS.......................................................11 4. TEST TYPES AND RESULTS....................................................................12 4.1 CONDUCTED EMISSION MEASUREMENT.............................................12 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT..........................12 4.1.2 TEST INSTRUMENTS...............................................................................13 4.1.3 TEST PROCEDURES...............................................................................14 4.1.4 DEVIATION FROM TEST STANDARD......................................................14 4.1.5 TEST SETUP.............................................................................................14 4.1.6 EUT OPERATING CONDITIONS...............................................................15 4.1.7 TEST RESULTS........................................................................................16 4.2 RADIATED EMISSION MEASUREMENT..................................................18 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT...............................18 4.2.2 TEST INSTRUMENTS...............................................................................19 4.2.3 TEST PROCEDURES...............................................................................20 4.2.4 DEVIATION FROM TEST STANDARD......................................................20 4.2.5 TEST SETUP.............................................................................................21 4.2.6 EUT OPERATING CONDITIONS...............................................................21 4.2.7 TEST RESULTS........................................................................................22 4.3 6dB BANDWIDTH MEASUREMENT.........................................................27 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT.......................................27 4.3.2 TEST INSTRUMENTS...............................................................................27 4.3.3 TEST PROCEDURE..................................................................................27 4.3.4 DEVIATION FROM TEST STANDARD......................................................27 4.3.5 TEST SETUP.............................................................................................28 4.3.6 EUT OPERATING CONDITIONS...............................................................28 4.3.7 TEST RESULTS........................................................................................29 Report No.: RF991230C02 3 Report Format Version 4.0.0 4.4 MAXIMUM OUTPUT POWER...................................................................30 4.4.1 LIMITS OF MAXIMUM OUTPUT POWER MEASUREMENT....................30 4.4.2 INSTRUMENTS.........................................................................................30 4.4.3 TEST PROCEDURES...............................................................................30 4.4.4 DEVIATION FROM TEST STANDARD......................................................31 4.4.5 TEST SETUP.............................................................................................31 4.4.6 EUT OPERATING CONDITIONS...............................................................31 4.4.7 TEST RESULTS........................................................................................32 4.5 POWER SPECTRAL DENSITY MEASUREMENT....................................33 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT..................33 4.5.2 TEST INSTRUMENTS...............................................................................33 4.5.3 TEST PROCEDURE..................................................................................33 4.5.4 DEVIATION FROM TEST STANDARD......................................................34 4.5.5 TEST SETUP.............................................................................................34 4.5.6 EUT OPERATING CONDITION.................................................................34 4.5.7 TEST RESULTS........................................................................................35 4.6 BAND EDGES MEASUREM…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST 4