TQ2-RFIDEXTNLRFID External Module

Feb. 2007 – All rights reserved P 1 RFID EM Module User Manual Ver 1.0 Feb. 2007 – All rights reserved P 2 Product Description RFID EM reader is a full function reader / writer operating in the 13.56MHz frequency band. RFID EM complies with the internationally recognized ISO-15693 standards. This RFID reader supports both Windows CE 4.2 / 4.21 and the Windows Mobile 5.0 operating system. RFID EM reader comes with integrated antenna and uses only +3.3VDC as its power supply. It is ideal for mobile device integration and no external antenna is required. Connectivity RFID EM reader communicates with external device through its system connector. The system connector supplies RFID EM reader with DC power and RS-232 (TTL level) signals for data exchange. The system connector is a 1.0mm pitch male mini connector. The signals are being described in the table below: Pin Signal Name Description 1 PWR +3.3VDC input 2 GND Ground 3 TXD RS-232 TX data, TTL level 4 RXD RS-232 RX data, TTL level 5 RFU Reserved for future usage 6 N/C Not connected Pin 1 Feb. 2007 – All rights reserved P 3 LED Indicator There are two LED on the RFID EM module, a Green LED and a RED LED. The Green LED will flash twice with duration of 0.5 sec upon power on and will stay off afterward. The Green LED will flash once (0.1sec ON) if any command issued through the system connector is executed successfully. The RED LED will flash once (0.1 sec ON) if command received through the system connector is not being carried out successfully. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no grantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help.

ETC Report No.: 06-12-MAS-046-01 Page A1 of A1 FCC ID.: TQ2-RFIDEXTNL ANNEX A: EXTERNAL CONSTRUCTION PHOTOS OF EUT 1. Outside view 1 of EUT 2. Outside view 2 of EUT

AB 7 6 4 5 3 2 A 1 B DCE 7 6 4 5 3 DC 2 E 1 MODEL:MODEL: TITLE: P/N:P/N: FILE NAME:FILE NAME: REV UNIT:UNIT: SCALE: MATERIAL:MATERIAL: FINISH: DESIGN: CHK: APP'D: A4 SHEET OF REV DATE DESCRIPTION DESIGN APP'D 1:1 Bigi RFID Labels List 1:1 2:1 Page: Model No.:RFID EM This device complies with Part 15 ofthe FCC Rules. Operation is subjectto the following two conditions:(1) this device may not cause harmfulinterference, and (2) this device mustaccept any interference received, including interference that may cause undesired operation. FCC ID TQ2 RFID XTNL : -E Model No.:RFID EM This device complies with Part 15 ofthe FCC Rules. Operation is subjectto the following two conditions:(1) this device may not cause harmfulinterference, and (2) this device mustaccept any interference received, including interference that may cause undesired operation. FCC ID TQ2 RFID XTNL : -E AB 7 6 4 5 3 2 A 1 B DCE 7 6 4 5 3 DC 2 E 1 MODEL:MODEL: TITLE: P/N:P/N: FILE NAME:FILE NAME: REV UNIT:UNIT: SCALE: MATERIAL:MATERIAL: FINISH: DESIGN: CHK: APP'D: A4 SHEET OF REV DATE DESCRIPTION DESIGN APP'D  Model No.:RFID EM This device complies with Part 15 ofthe FCC Rules. Operation is subjectto the following two conditions:(1) this device may not cause harmfulinterference, and (2) this device mustaccept any interference received, including interference that may cause undesired operation. FCC ID TQ2 RFID XTNL : -E

ETC Report No.: 06-12MAS-046-01 Page B1 of B1 FCC ID.: TQ2-RFIDEXTNL ANNEX B: INTERNAL CONSTRUCTION PHOTOS OF EUT 1. Front view of PCB 2. Rear view of PCB

ETC Report No. : 06-12-MAS-046-01 Sheet 1 of 19 Sheets FCC ID.: TQ2-RFIDEXTNL Rev. No 1.0 CONFORMANCE TEST REPORT FOR FCC 47 CFR, Part 15 Subpart B & C Report No.: 06-12-MAS-046-01 Client: Shin Chuan Computer Co., Ltd. Product: RFID External Module Trade Name: ---- Model No.: RFID EM，MARS-1030A-RFIDxxx (Agent) FCC ID: TQ2-RFIDEXTNL Manufacturer/supplier: AMIC Technology Corporation. Representation/Agency: ADVANTECH CO., LTD Date test item received: 2006/12/06 Date test campaign completed: 2007/01/26 Date of issue: 2007/01/26 The test result only corresponds to the tested sample. It is not permitted to copy this report, in part or in full, without the permission of the test laboratory. Total number of pages of this test report: 19 pages Total number of pages of photos: External photos 1 page Internal photos 1 pages Setup photos 2 pages Test Engineer Checked By Approved By Mark James Joe Hsieh ELECTRONICS TESTING CENTER, TAIWAN NO.8, LANE 29, WENMING RD., LESHAN TSUEN, GUISHAN SHIANG, TAOYUAN COUNTY, TAIWAN 33383, R.O.C.TAIWAN, R.O.C. TEL: (03) 3276170~4 INT: +886-3-3276170~4 FAX: (03) 3276188 INT: +886-3-3276188 ETC Report No. : 06-12-MAS-046-01 Sheet 2 of 19 Sheets FCC ID.: TQ2-RFIDEXTNL Rev. No 1.0 Client : Shin Chuan Computer Co., Ltd. Address : 6F-2, 268, LianCheng Rd., ZhongHe City, Taipei Country 23553, Taiwan (R.O.C.) Manufacturer : AMIC Technology Corporation. Address : No. 2, Li-Hsin 6 th Road, Science-Based Industrial Park, Hsin-Chu City, 300, Taiwan, R.O.C. Representation/Agency : ADVANTECH CO., LTD Address : No. 1, Alley 20, Lane 26, Rueiguang Rd, Neihu District, Taipei, Taiwan 114 EUT : RFID External Module Trade name : ---- Model No. : RFID EM，MARS-1030A-RFIDxxx (Agent) Power Source : 3.3V DC Regulations applied : FCC 47 CFR, Part 15 Subpart B & C (2006) The testing described in this report has been carried out to the best of our knowledge and ability, and our responsibility is limited to the exercise of reasonable care. This certification is not intended to believe the sellers from their legal and/or contractual obligations. The compliance test is only certified for the test equipment and the results of the testing report relate only to the item tested. The compliance test of this report was conducted in accordance with the appropriate standards. It’s not intention to assure the quality and performance of the product. This report shall not be reproduced except in full, without the approval of ETC. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. Laboratory Introduction: Electronics Testing Center, Taiwan is recognized, filed and mutual recognition arrangement as following: 1 ISO9001: TüV Product Service 2 ISO/IEC 17025: BSMI, CNLA, DGT, NVLAP, CCIBLAC, UL, Compliance 3 Filing: FCC, Industry Canada, VCCI 4 MRA: Australia, Hong Kong, New Zealand, Singapore, USA, Japan, Korea, China, APLAC through CNLA 5 FCC Registration Number: 90588, 91094, 91095 NVLAP Lab Code 200133-0 ETC Report No. : 06-12-MAS-046-01 Sheet 3 of 19 Sheets FCC ID.: TQ2-RFIDEXTNL Rev. No 1.0 Table of Contents Page 1. GENERAL INFORMATION ...................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION.................................................................................................................................................4 1.2 CHARACTERISTICS OF DEVICE: ......................................................................................................................................4 1.3 TEST METHODOLOGY....................................................................................................................................................4 1.4 TEST FACILITY...............................................................................................................................................................4 2. TEST SYSTEM AND LIMITATION ......................................................................................................................... 5 2.1 DEVICE FOR TESTED SYSTEM........................................................................................................................................5 2.2 RESTRICTED BANDS OF OPERATION...............................................................................................................................5 2.3 LIMITATION....................................................................................................................................................................6 2.4 LABELING REQUIREMENT..............................................................................................................................................7 2.5 USER INFORMATION.......................................................................................................................................................7 3. RADIATED EMISSION MEASUREMENT.............................................................................................................. 8 3.1 APPLICABLE STANDARD.................................................................................................................................................8 3.2 MEASUREMENT PROCEDURE.........................................................................................................................................8 3.3 TEST DATA..................................................................................................................................................................11 3.4 CALCULATION..............................................................................................................................................................14 3.5 RADIATED TEST EQUIPMENT.......................................................................................................................................14 3.6 MEASURING INSTRUMENT SETUP.....…

Text truncated - open the document above for the full version.

ETC Report No. : 06-12MAS-046-01 Sheet 1 of 2 Sheets FCC ID.: TQ2-RFIDEXTNL Photos of Radiation Measuring Setup x-axis ETC Report No. : 06-12MAS-046-01 Sheet 2 of 2 Sheets FCC ID.: TQ2-RFIDEXTNL y-axis z-axis