TTM-105P25REX-5r Digital Microwave Radio

EX-5r 5GHz Digital Microwave Radio Installation & Management Part Number: 50000007 Date: 2006-05-17 Exalt Communications Inc. EX-5r Installation & Management Page i 5000007 2006-05-17 Legal Notice The information contained herein is the property of Exalt Communications, Inc. (“Exalt”) and is supplied without liability for errors or omissions. No part of this document may be reproduced, in any form, except as authorized by contract or other written permission from the owner. Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective holders. The contents of this document are current as of the date of publication. Exalt reserves the right to change the contents without prior notice. The publication of information in this document does not imply freedom from patent or other rights of Exalt or others. © Exalt Communications Inc., May 2006. All rights reserved. The Exalt logo is a trademark of Exalt Communications, Inc. Exalt Communications Inc. EX-5r Installation & Management Page ii 5000007 2006-05-17 About this Document This manual provides a complete description of the Exalt EX-5r Digital Microwave Radio and related software. The purpose of this manual is to provide the planner, engineer, installer, system administrator, and technician with general and specific information related to the planning, installation, operation, management and maintenance of the device. Revision History Date Detail 2006-05-17 Initial release Icons Throughout this document, the following icons are used to denote specific types of information as described here. (Warning) Denotes information pertaining to potential danger to human life. (Caution) Denotes information pertaining to potential danger to property. (Note) Denotes information that may be particularly useful or unique ! CAUTION Exalt Communications Inc. EX-5r Installation & Management Page iii 5000007 2006-05-17 General Compliance and Safety The usage of radio transmission devices is subject to specific regulatory requirements governed by regional legislation. In most cases, the specific device must be authorized for use in a given country and must be installed and adjusted in accordance with specific radio-frequency settings and in a manner that has been authorized specific to the device itself in accordance with the specific location of the device. Some users may be completely or partially restricted from use of the device. Please consult your governmental agency/agencies for regulatory requirements before use, or contact Exalt or your Exalt authorized dealer for assistance. This device may not be modified in any way without the express written consent of Exalt. Modification will not only void the manufacturer warranty, but may also be expressly illegal in accordance to government regulations. In addition, there are no user-serviceable parts or assemblies inside the product housing. There may also be voltages, signals and mechanisms within the device that could be harmful to human safety. The mounting of this device and associated peripherals and connections (inclusive of antenna mast, antenna, cabling, egress, lightning protection devices, grounding, power, etc.) may be subject to regional requirements for health and human safety. A qualified professional installer and an electrician are highly recommended, and may be required by law. For example, within the USA, this device must be professionally installed to ensure that the system implementation meets FCC regulations. Exalt cannot warrant the device or be found liable for any unauthorized use or installation of the device. Regulatory Notices Federal Communications Commission (FCC), United States The device is allowed to be used provided it does not cause interference to other devices. It is not guaranteed to provide protection against interference from other electronic and radio devices. The system has been tested and found to comply with the limits of a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures: • Reorient or relocate the receiving antenna. Exalt Communications Inc. EX-5r Installation & Management Page iv 5000007 2006-05-17 • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC regulations. Changes or modifications not expressly approved in writing by Exalt may void the user’s authority to operate this equipment. This device must be professionally installed. In order to comply with regulations, the output power of this device may need to be adjusted in accordance to the associated transmission system. See section 2.3 of this manual for details. The antenna associated with this device shall be mounted in a location that is at least 22 feet away from humans that may be subject to long-term or continuous exposure. Industry Canada (IC), Canada This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the…

Text truncated - open the document above for the full version.

Exalt Communications Inc. 580 Division St. Campbell, CA 95008 USA telephone: +1 (408) 871-1804 fax: +1 (408) 871-9750 May 22, 2006 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 RE: Request for Confidential Treatment from public disclosure Exalt Communications Inc. EX-5r (FCC ID: TTM-1Ø5P25R) Dear Sirs/Madam, Exalt Communications would like to request that the following documents: - Schematics - Bill of Materials - Block Diagram - Operational Description - Detailed Circuit Board Photos submitted with the application for certification be withheld from public disclosure per Section 0.459 of the FCC Rules. This confidentiality request is made under the provisions of Section 0.457(d) of the FCC Rules and Section 552(b)(4) of the Freedom of Information Act. The various items contain proprietary, confidential and trade secret materials, which would not customarily be made available for public inspection. The product is permanently mounted and sealed. Also, as installed, the equipment is not generally accessible to the public -- typically mounted in telecom equipment shelters and secure rooms. If you have any questions, please do not hesitate to contact me. Sincerely, Ken Ruppel Director, Customer Engineering Exalt Communications Inc. [email protected] 408-871-1804 x226

MiCOM Labs, 3922 Valley Avenue, Suite “B”, Pleasanton, CA 94566 Tel: +1 (925) 462-0304, Fax: +1 (925) 462-0306, Web: www.micomlabs.com the wireless lab June 21, 2006 EXLT03 – 5 GHz Point to Point Fixed Link Radio Exalt Communications, Inc. External Photograph Model EX-5r Page 2 of 2 the wireless lab

Model: EX-5r FCC ID: TTM-1Ø5P25R IC: 6254A-1Ø5P25R Electrical Ratings: +48VDC, 0.7 A The device complies with Part 15 of the FCC Rules and IC: RSS-210. Operation is subject to the following conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. (3) This device must be professionally installed. MADE IN USA Part Number — Serial Number E123456 — 1234567890 P/N S/N MAC Address 12:34:56:78:90:AB MAC 1.65” 3.3” Regulatory Label Detail, and Label Location Exalt Communications Inc EX-5r Bottom Side View– Label Location Label Location (Bottom Side Panel)

3922 Valley Avenue, Suite “B”, Pleasanton, California 94566 USA Tel: 1 925 462 0304, Fax: 1 925 462 306 www.micomlabs.com Friday 7 th July 2006 EXLT03-A2 Exalt Communications Inc , Model EX-5r Maximum Permissible Exposure Calculations FCC, Part 15 Subpart C §15.247(i) Industry Canada RSS-Gen §5.5 Calculations for Maximum Permissible Exposure Levels Power Density = Pd (mW/cm 2 ) = EIRP/(4πd 2 ) EIRP = P * G P = Peak output power (mW) G = Antenna numeric gain (numeric) d = Separation distance (cm) Numeric Gain = 10 ^ (G (dBi)/10) P (Worst case) = +29.98 dBm, (995.4 num) Antenna gains = 20 dBi (100 num), 28 dBi (631 num.), 37.5 dBi (5623 num.) Because the EUT belongs to the General Population / Uncontrolled Exposure the limit of power density is 1.0 mW/cm 2 Peak Output Power (dBm) Peak Output Power (mW) Antenna Gain (dBi) Single/ Dual Pole Numeric Gain (numeric) Ant Port #1 Ant Port #2 Ant Port #1 Ant Port #2 Calculated Safe Distance @ 1mW/cm 2 Limit (cm) 20.0 Dual 100 +26.98 +26.98 498.9 498.9 89.0 28.0 Single 631 +29.98 995.4 223.6 37.5 Dual 5623 +26.98 +26.98 498.9 498.9 667.4

COVER PAGE Test of Model EX-5r (Dual Polarized) To: FCC 47 CFR Part15.247 & IC RSS-210 Test Report Serial No.: EXLT03-A2 Rev A TITLE PAGE TEST REPORT FROM Test of Model EX-5r (Dual Polarized) to FCC 47 CFR Part15.247 & IC RSS-210 Test Report Serial No.: EXLT03-A2 Rev A Note: this report only contains data with regard to the 5.8 GHz operational modes of the EX-5r. 5250-5350 MHz test data is reported in MiCOM Labs test report EXLT03-A5 This report supersedes: None Manufacturer: Exalt Communications, Inc 580 Division Street Campbell, California 95008 USA Product Function: 5 GHz (Dual Polarized) Point to Point Fixed Link Radio Copy No:pdf Issue Date: 10th July 06 This Test Report is Issued Under the Authority of; MiCOM Labs, Inc. 3922 Valley Avenue, Suite B Pleasanton, CA 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com CERTIFICATE #2381.01 MiCOM Labs is an ISO 17025 Accredited Testing Laboratory This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. Title: Model EX-5r (Dual Polarized) To: Serial #: Issue Date: Page: FCC 47 CFR Part15.247 & IC RSS-210 EXLT03-A2 Rev A 10th July 06 3 of 143 This test report may be reproduced in full only. The document may only be updated by MiCOM This page has been left intentionally blank Labs personnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 3922 Valley Avenue, Suite B, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com Title: Model EX-5r (Dual Polarized) To: Serial #: Issue Date: Page: FCC 47 CFR Part15.247 & IC RSS-210 EXLT03-A2 Rev A 10th July 06 4 of 143 This test report may be reproduced in full only. The document may only be updated by MiCOM TABLE OF CONTENTS ACCREDITATION & LISTINGS.........................................................................................5 1. TEST RESULT CERTIFICATE...................................................................................8 2. REFERENCES AND MEASUREMENT UNCERTAINTY..........................................9 2.1. Normative References...............................................................................................9 2.2. Test and Uncertainty Procedures..............................................................................9 3. PRODUCT DETAILS AND TEST CONFIGURATIONS..........................................10 3.1. Technical Details.....................................................................................................10 3.2. Scope of Test Program............................................................................................11 3.3. Equipment Model(s) and Serial Number(s).............................................................13 3.4. Antenna Details.......................................................................................................14 3.5. Cabling and I/O Ports..............................................................................................14 3.6. Test Configurations..................................................................................................15 3.7. Equipment Modifications..........................................................................................17 3.8. Deviations from the Test Standard..........................................................................17 3.9. Subcontracted Testing or Third Party Data.............................................................17 4. TEST SUMMARY......................................................................................................18 5. TEST RESULTS........................................................................................................20 5.1. Device Characteristics.............................................................................................20 5.1.1. 6 dB and 99 % Bandwidth........................................................................20 5.1.2. Peak Output Power..................................................................................30 5.1.3. Peak Power Spectral Density...................................................................40 5.1.4. Maximum Permissible Exposure..............................................................50 5.1.5. Conducted Spurious Emissions...............................................................51 5.1.6. Radiated Emissions.................................................................................67 5.1.7. AC Wireline Conducted Emissions (150 kHz – 30 MHz)........................118 6. PHOTOGRAPHS.....................................................................................................121 6.1. Radiated Emissions (30 MHz-1 GHz)....................................................................121 6.2. Radiated Emissions >1 GHz..................................................................................122 6.3. Conducted Emissions (150 kHz - 30 MHz)............................................................123 6.4. General Measurement Test Set-Up.......................................................................124 7. TEST EQUIPMENT DETAILS.................................................................................125 Appendix A - 16 QAM and 64 QAM Verification Data...............................................127 A.1. Device Characteristics...........................................................................................129 A.1.1. Conducted Band Edge...........................................................................129 A.1.2. Radiated Emissions Transmitter Radiated Spurious Emissions............135 Labs personnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 3922 Valley Avenue, Suite B, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com A.1.3. Peak Field Strength Measurements.........................…

Text truncated - open the document above for the full version.