TVE-120502802.11 ac Module

802.11 a/n/ac Module PCE4502AN User’s Manual PRODUCT DESCRIPTION The PCE4502AN is adapting the next generation Wi-Fi technology, 802.11ac. It provides the great improvement in performance compare with 802.11n by utilizing 2Tx / 2Rx technology to achieve 867Mbps throughput on the 5GHz bands. PRODUCT SPECIFICATION Hardware Specification Standard IEEE802.11a; IEEE802.11n; IEEE802.11ac RF QCA9882 Interface 64-bit PCI-E Operating Voltage 3.3v Antenna Connectors I-PEX x2 Radio specification Data rate 867Mbps Channel Data rate Typical Rx Sensitivity (dBm combined) 802.11a 6Mbps ≦-92 dBm 54 Mbps ≦-74 dBm 802.11a/n_HT20 MCS 0/8 ≦-91 dBm MCS 7/15 ≦-72 dBm 802.11n_HT40 MCS 0/8 ≦-90 dBm MCS 7/15 ≦-70 dBm 802.11ac_HT80 MCS 0 ≦-87 dBm MCS 9 ≦-62 dBm * All RF parameters tolerance are +2/-1 dBm Antenna Specification (Internal Antennas) Antenna 2 x Antennas Type Internal PIFA Antenna Peak Gain (dBi) 5150~5250MHz 5250~5350MHz 5470~5725MHz 5725~5850MHz Ant0 5.74 5.91 6.13 3.78 Ant1 5.50 5.40 4.74 4.29 Environment Operation temperature 0-40 deg C Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: TVE-120502”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

FCC ID: TVE-120502 Report No.: RF140217C18 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch March 10, 2014 Dear Application Examiner, Fortinet Inc., It’s a 802.11 ac Module, FCC ID: TVE-120502 would like to have your authorization as a modular device. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip QCA9882. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is QCA9882. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: TVE-120502 Report No.: RF140217C18 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

Label Location

Model :PCE4502AN IC: 7280B-120502 FCC ID: TVE-120502

Page 3 Page 4 Page 5 Page 6 Page 7

Report No.: SA140217C18 1 of 7 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA140217C18 MODEL NO.: PCE4502AN FCC ID: TVE-120502 IC: 7280B-120502 RECEIVED: Feb. 17, 2014 TESTED: Feb. 19 ~ Feb. 25, 2014 ISSUED: Feb. 26, 2014 APPLICANT: Fortinet Inc. ADDRESS: 899 Kifer Road Sunnyvale, CA 94086, USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA140217C18 2 of 7 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ........................................................................................................... 4 2. RF EXPOSURE ............................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ....................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................. 6 2.3 CLASSIFICATION ......................................................................................................... 7 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ................................ 7 Report No.: SA140217C18 3 of 7 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140217C18 Original release Feb. 26, 2014 Report No.: SA140217C18 4 of 7 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: 802.11 ac Module MODEL: PCE4502AN BRAND: Fortinet APPLICANT: Fortinet Inc. TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 RSS-102 Issue 4 (2010-12) The above equipment (Model: PCE4502AN) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Feb. 26, 2014 Pettie Chen / Senior Specialist APPROVED BY : , DATE :Feb. 26, 2014 Ken Liu / Senior Manager Report No.: SA140217C18 5 of 7 Report Format Version 5.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) For FCC Part 2 (Section 2.1091) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz For RSS-102 Issue 4 (2010-12) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (W/m 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/150 6 1500-100,000 ... ... 10 6 F = Frequency in MHz Report No.: SA140217C18 6 of 7 Report Format Version 5.0.0 2.2 MPE CALCULATION FORMULA For FCC Part 2 (Section 2.1091) Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm For RSS-102 Issue 4 (2010-12) Pd = (Pout*G) / (4*pi*r2) where Pd = power density in W/m2 Pout = output power to antenna in W G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in meter Report No.: SA140217C18 7 of 7 Report Format Version 5.0.0 2.3 CLASSIFICATION For FCC Part 2 (Section 2.1091) The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. For RSS-102 Issue 4 (2010-12) The antenna of this product, under normal use condition, is at least 0.2m away from the body of the user. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER For FCC Part 2 (Section 2.1091) FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 5180-5240 16.99 8.76 20 0.075 1 5745-5825 24.70 8.76 20 0.441 1 NOTE: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 ) 2 /2] = 8.76dBi For RSS-102 Issue 4 (2010-12) FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (m) POWER DENSITY (W/m 2 ) LIMIT (W/m 2 ) 5180-5240 16.99 8.76 0.2 0.75 10 5745-…

Text truncated - open the document above for the full version.

Report No.: RF140217C18 R1 1 of 71 Report Format Version 5.2.0 Cancels and replaces the report No.: RF140217C18 dated Feb. 26, 2014 FCC TEST REPORT (15.247) IC TEST REPORT (RSS-210 Issue 8 (2010-12)) REPORT NO.: RF140217C18 R1 MODEL NO.: PCE4502AN FCC ID: TVE-120502 IC: 7280B-120502 RECEIVED: Feb. 17, 2014 TESTED: Feb. 19 ~ Feb. 25, 2014 ISSUED: Mar. 05, 2014 APPLICANT: Fortinet Inc. ADDRESS: 899 Kifer Road Sunnyvale, CA 94086, USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140217C18 R1 2 of 71 Report Format Version 5.2.0 Cancels and replaces the report No.: RF140217C18 dated Feb. 26, 2014 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................. 4 1. CERTIFICATION .......................................................................................................... 5 2. SUMMARY OF TEST RESULTS ................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY ............................................................................... 6 3. GENERAL INFORMATION .......................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................ 7 3.2 DESCRIPTION OF TEST MODES .............................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .............................. 9 3.3 DUTY CYCLE OF TEST SIGNAL .............................................................................. 11 3.4 DESCRIPTION OF SUPPORT UNITS ...................................................................... 12 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ....................................................... 12 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................... 13 4. TEST TYPES AND RESULTS (FOR 5.0GHz BAND) ................................................ 14 4.1 RADIATED EMISSION MEASUREMENT ................................................................. 14 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT ............................................... 14 4.1.2 TEST INSTRUMENTS ............................................................................................... 15 4.1.3 TEST PROCEDURES ............................................................................................... 16 4.1.4 DEVIATION FROM TEST STANDARD...................................................................... 16 4.1.5 TEST SETUP ............................................................................................................. 17 4.1.6 EUT OPERATING CONDITIONS .............................................................................. 18 4.1.7 TEST RESULTS ........................................................................................................ 19 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................ 39 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .......................................... 39 4.2.2 TEST INSTRUMENTS ............................................................................................... 39 4.2.3 TEST PROCEDURES ............................................................................................... 40 4.2.4 DEVIATION FROM TEST STANDARD...................................................................... 40 4.2.5 TEST SETUP ............................................................................................................. 40 4.2.6 EUT OPERATING CONDITIONS .............................................................................. 40 4.2.7 TEST RESULTS ........................................................................................................ 41 4.3 6dB BANDWIDTH MEASUREMENT ......................................................................... 45 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ...................................................... 45 4.3.2 TEST SETUP ............................................................................................................. 45 4.3.3 TEST INSTRUMENTS ............................................................................................... 45 4.3.4 TEST PROCEDURE ................…

Text truncated - open the document above for the full version.

Report No.: RF140217C18-1 R1 1 of 72 Report Format Version 5.2.0 Cancels and replaces the report No.: RF140217C18-1 dated Feb. 26, 2014 FCC TEST REPORT (15.407) IC TEST REPORT (RSS-210 Issue 8 (2010-12)) REPORT NO.: RF140217C18-1 R1 MODEL NO.: PCE4502AN FCC ID: TVE-120502 IC: 7280B-120502 RECEIVED: Feb. 17, 2014 TESTED: Feb. 19 ~ Feb. 25, 2014 ISSUED: Mar. 05, 2014 APPLICANT: Fortinet Inc. ADDRESS: 899 Kifer Road Sunnyvale, CA 94086, USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140217C18-1 R1 2 of 72 Report Format Version 5.2.0 Cancels and replaces the report No.: RF140217C18-1 dated Feb. 26, 2014 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 4 1. CERTIFICATION .................................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................................ 6 2.1 MEASUREMENT UNCERTAINTY ......................................................................................... 6 3. GENERAL INFORMATION ..................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ....................................................................................... 7 3.2 DESCRIPTION OF TEST MODES ......................................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................................ 9 3.3 DUTY CYCLE OF TEST SIGNAL ........................................................................................ 11 3.4 DESCRIPTION OF SUPPORT UNITS ................................................................................. 15 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................................. 15 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ...................................................... 16 4. TEST TYPES AND RESULTS .............................................................................................. 17 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .............................................. 17 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ........................... 17 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS ....................... 17 4.1.3 TEST INSTRUMENTS ......................................................................................................... 18 4.1.4 TEST PROCEDURES .......................................................................................................... 19 4.1.5 DEVIATION FROM TEST STANDARD ................................................................................ 19 4.1.6 TEST SETUP ........................................................................................................................ 20 4.1.7 EUT OPERATING CONDITION ........................................................................................... 21 4.1.8 TEST RESULTS ................................................................................................................... 22 4.2 CONDUCTED EMISSION MEASUREMENT ....................................................................... 42 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .................................................... 42 4.2.2 TEST INSTRUMENTS ......................................................................................................... 42 4.2.3 TEST PROCEDURES .......................................................................................................... 43 4.2.4 DEVIATION FROM TEST STANDARD ................................................................................ 43 4.2.5 TEST SETUP ........................................................................................................................ 43 4.2.6 EUT OPERATING CONDITIONS ......................................................................................... 43 4.2.7 TEST RESULTS ................................................................................................................... 44 4.3 PEAK TRANSMIT POWER MEASUREMENT ............................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST (Test mode A) 2 3 CONDUCTED EMISSION TEST (Test mode B) 4 5 RADIATED EMISSION TEST (Test mode A) 6 7 RADIATED EMISSION TEST (Test mode B) 8