TWC-TATETX0401Tire pressure monitoring transmitter

1 2 TIRE PRESSURE MONITORING SYSTEM Owner’s Manual ź Suitable for all types of vehicles from 4~22 wheels Kysonix Inc. reserves the right to change the contents of this manual at any time and without notice. The information contained in this manual is proprietary and must not be reproduced without prior consent from Kysonix Inc. 3 4 TABLE OF CONTENTS Introduction -------------------------------------------------------------------------5 Notices --------------------------------------------------------------------------------6 FCC Notice--------------------------------------------------------------------------- 7 European Regulations--------------------------------------------------------------- 8 System Scope of Use and Warnings-----------------------------------------------8 SecuTire System and Tire Maintenance-------------------------------------------8 System Installation and Usage------------------------------------------------------8 Reacting to Alerts---------------------------------------------------------------------9 Power Connection---------------------------------------------------------------------9 Operation-----------------------------------------------------------------------------10 Installation----------------------------------------------------------------------------11 Display Installation(Square)--------------------------------------------------------12 Display Installation(Round)--------------------------------------------------------13 Sensor Installation--------------------------------------------------------------------14 Power Connection--------------------------------------------------------------------15 Battery Replacement-----------------------------------------------------------------16 Panel Description of Display-------------------------------------------------------17 Components Description of Sensor Transmitter---------------------------------18 Parts View-----------------------------------------------------------------------------19 System Maintenance & Simple Troubleshooting----------------------------20 After-sales Service------------------------------------------------------------------21 Technical Specification------------------------------------------------------------22 Sensor ------------------------------------------------------------------------------------22 Display ------------------------------------------------------------------------------------23 Appendix ------------------------------------------------------------------------------- 24 Glossary-----------------------------------------------------------------------------------24 Attention ----------------------------------------------------------------------------------25 Components and Accessories----------------------------------------------------------26 Part No. View-----------------------------------------------------------------------------28 illustration of Sensor and Display-----------------------------------------------------29 Vehicles applicable----------------------------------------------------------------------30 ADDChina•Nanchang•Gaoxin Area TEL0791-8161526 FAX0791-8161653 WEBwww.kysonix.com(Chinese) www.secutire.com(English) 5 6 Introduction ඖ Thank you for choosing SecuTire. To ensure your proper operation, please read this manual carefully. Kysonix Inc. holds the right of the manual’s final explanation. ඖNotices Congratulations! As the owner of this state-of-the-art wireless tire pressure monitor system, you will enjoy the improved convenience and benefits of having tire pressure information automatically monitored while you are driving. SecuTire system consists of sensor transmitter and receivi ng display, which can monitor low tire pressure inside each tire and transmit this data to the receiver. Having carried out the correct installation procedure (see Installation section in this manual), SecuTire system is ready to use. 7 ඖ FCC Notice This system complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This system may not cause harmful interference, and (2)This system must accept any interference received, including interference thatmay cause undesired operation. This system has been tested and found to comply with the limits for a Class B Digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. If not installed and used in accordance with the instructions, the radio frequency energy the system generates, uses and radiates may cause harmful interference to radio communication. However, there’s no guarantee that interference will not occur in a particular situation. If this system does cause harmful interference to radio or television reception, which can be determined by turning the system off, the user is encouraged to try to correct the interference by the following measures: Reorient or Relocate the receiving antenna. •Increase the separation between the receiver and the system. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. Changes or modifications to this system without the express approval of Kysonix Inc. may void the user’s authority to the product warranty. 8 9 ඖEuropean Regulations This system complies with all European Electromagnetic compatibility regulations (95 54/EC and EN300 220-1).This system has been tested and found to comply with the above regulations, and in addition it meets the requirements for low powered transmitters/receivers as defined by the relevant radio approval authority. The regulations are designed to provide reasonable protection against harmful interference or susceptibility. Changes made to this system without the express approval of Kysonix Inc. may void the user’s authority to use the system. ඖSystem Installation and Usage ඖSecuTire System and Tire Maint…

Text truncated - open the document above for the full version.

Description of Operation 1. The learning method of the transmitter and receiver: 1 st step: Power on the receiver and press RESET button, meanwhile press the PGM button and hold over 8 seconds until all the red lamps on the receiver are lit. 2 nd step: Install the battery of one transmitter and remove all the other transmitters’ battery. Press the PGM button (hold time less than 5 seconds), then the signal lamp (first yellow lamp) will flash and the red lamp corresponding to the tire position will also flash. Now the learning is finished. 3 rd step: Removed the battery of the transmitter that already finished learning process. Repeat the process of all other transmitters. 4 th step: Install all the transmitters’ battery and check the red lamps corresponding to the tire are flashing. If not, go back to step 1,2,3. Note: Rest button means that let the product go back to initial state. 2. Function of the transmitter and the receiver: When the pressure of the tire is lower than reset pressure, transmitter be activated and transmits signal, then the corresponding red lamp of the receiver will be lit. At the same time, receiver will make alert sound for 30s and stop for 30s and repeat until the pressure of the tire become normal.

670 National Avenue, Mountain View, CA 94043 Tel. (650) 988-0900 Fax (650) 988-6647 www.ecmg-global.com FCC CERTIFICATION RADIO MEASUREMENT TECHNICAL REPORT On Model Name: Tire pressure monitoring transmitter Model Number : TAT-E-TX Trademark : FCC ID : TWC-TATETX0401 Prepared for Jiangxi Kysonix Inc. According to FCC Part 15 (2004), Subpart C Test Report #: JIA-0512-0175SH-FCC Prepared by: Chris Huang QC Manager: Harry Zhao Test Report Released by: 2005, December 27 th ⎯⎯⎯⎯⎯⎯⎯⎯⎯ ⎯⎯⎯⎯⎯⎯ Harry Zhao Date NVLAP Lab code: 200068-0 ISO/IEC 17025:1999, ISO 9002:1994 Test Location Tests performed at EMC Compliance Management Group (China) in a Certified ANSI Semi-Anechoic Chamber and Shielded Room performed testing. Test Site Location: Jiangsu Electronic Products Supervision & Inspection Institute No 107 Ge lane ZhongQiao WuXi JiangSu, China Tel: 86-510-5140037 Fax: 86-510-5105579 Registration Number: 399439 Accreditation Bodies EMC Compliance Management Group is a fully accredited Test Laboratory for ITE, ISM and Telecommunications Products. In compliance with the site registration requirements of Section 2.948 of the FCC Rules to perform EMI measurements for the general public. Accredited by the National Voluntary Laboratory Accreditation Program for the specific scope of accreditation under Lab Code # 200068-0. Table of Contents DISCLAIMER NOTICE _________________________________________ 1 REPRODUCTION CLAUSE_____________________________________ 1 ADMINISTRATIVE DATA _____________________________________ 2 EUT DESCRIPTION ___________________________________________ 2 TEST SUMMARY _____________________________________________ 3 TEST MODE JUSTIFICATION _________________________________ 4 EUT EXERCISE SOFTWARE ___________________________________ 4 EQUIPMENT MODIFICATION _________________________________ 4 TEST SYSTEM DETAILS ______________________________________ 5 CONFIGURATION OF TESTED SYSTEM________________________ 6 EUT SAMPLE PHOTOS OF TAT-E-TX __________________________ 7 ATTACHMENT 1 – ANTENNA REQUIREMENT_________________ 11 ATTACHMENT 2 – RESTRICTED BAND OF OPERATION_______ 14 ATTACHMENT 3 – OPERATION MODE _______________________ 21 ATTACHMENT 4 –FIELD STRENGTH OF FUNDAMENTAL AND SPURIOUS EMISSIONS__________________________________________________ 25 ATTACHMENT 5 – BANDWIDTH _____________________________ 35 EMC Test Report #: JIA-0512-0175SH-FCC Prepared for Jiangxi Kysonix Inc. Prepared by EMC Compliance Management Group Page 1 of 38 Disclaimer Notice When government drawing, specification, or other data are used for any purpose other than in connection with a definitely related government procurement operation, the United States Government thereby incurs no responsibility nor any obligation whatsoever; and the fact that the Government may have formulated, furnished, or in any way supplied the said drawing, specifications, or other data, is not to be regarded by implication or otherwise in any manner licensing the holder or any other person or corporation, or conveying any rights or permission to manufacture, use, or sell patented invention that may in any way be related thereto. This report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government. Reproduction Clause Any reproduction of this document must be done in full. No single part of this document may be reproduced without permission from EMC Compliance Management Group, 670 National Ave., Mountain View, CA 94043. Opinions and Interpretations This test report relates to the abovementioned equipment under test (EUT). Without the permission of EMC Compliance Management Group Test Lab this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark on this or similar products. The manufacturer has sole responsibility of continued compliance of the device. Statement of Measurement Uncertainty The data and results referenced in the document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities that can account for a nominal measurement error. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. EMC Test Report #: JIA-0512-0175SH-FCC Prepared for Jiangxi Kysonix inc. Prepared by EMC Compliance Management Group Page 2 of 38 Administrative Data Test Sample : Tire pressure monitoring transmitter Model Number : TAT-E-TX Models Tested : TAT-E-TX Trade Mark : Date Tested : 2005, December 19 th Applicant : Jiangxi Kysonix Inc. 801 Huoju Street, Gaoxing District, Nanchang, Jiangxi, China 330069 Telephone : 86-791-8161525 Fax : 86-791-8161653 Manufacturer : Jiangxi Kysonix Inc. 801 Huoju Street, Gaoxing District, Nanchang, Jiangxi, China 330069 EUT Description Jiangxi Kysonix Inc. Model number TAT-E-TX (referred to as the EUT in this test report) is a Tire pressure monitoring transmitter. EMC Test Report #: JIA-0512-0175SH-FCC Prepared for Jiangxi Kysonix inc. Prepared by EMC Compliance Management Group Page 3 of 38 Test Summary The Electromagnetic Compatibility requirements on TAT-E for this test are stated below. All results listed in this report relate exclusively to this above-mentioned model as the Equipment Under Test. This report confers no approval or endorsement upon any other component, host or subsystem used in the test set-up. EMC Test Items Reference FCC Part 15 (2004), Subpart C Specification Description Test Results Remark FCC Part 15.203 Antenna Requirement Compliance Attachment 1 FCC Part 15.205 Restricted Band of Operation Compliance Attachment 2 FCC Part 15.207 Conducted Limits Test is not applicable, because EUT only employ battery power for operation. FCC Part 15.209 Radiated Emission Limits Compliance Refer to Attachment 4 FCC Part 15.231 Periodic Operation in the Band 40.66-40.70MHz and above 70MHz -- -- (e) Operation Mode Compliance Attachment 3 (e) Field Strength of Fundamental and Spuri…

Text truncated - open the document above for the full version.