TYV-XTC5000Digital Satellite Receiver

1 User’s Guide DIGITAL SATELLITE RECEIVER XTC 5000 2 This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ◎Reorient or relocate the receiving antenna. ◎Increase the separation between the equipment and receiver. ◎Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ◎Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void the user's authority to operated the equipment under FCC rules. XTC MOTORSPORTS INC. ADDRESS : 205 CHAMPAGNE DRIVE UNIT 3, TORONTO, ON, M3L 2C6, CANADA DIGITAL SATELLITE RECIEVER FCC ID : TYV-XTC5000 MODEL NO : XTC 5000 POWER : Input Voltage 90 - 250V AC @ 50Hz/60Hz±5% 3 "IMPORTANT SAFETY INSTRUCTIONS", or the equivalent. The safety instructions shall include, as applicable to the particular apparatus, the information and warnings listed below: 1)Read these instructions. 2)Keep these instructions. 3)Heed all warnings. 4)Follow all instructions. 5)Do not use this apparatus near water. 6)Clean only with a dry cloth. 7)Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. 8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9)Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11)Only use the attachments/accessories specified by the manufacturer. 12)Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13)Unplug this apparatus during lightning storms or when unused for long periods of time. 14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 4 XTC 5000– Digital Satellite Receiver CONTENTS Page 13 14 15 15 17 18 19 21 22 23 24 25 26 CHANNEL MANAGER Channel Manager Favorite Channel Move Channel Lock Channel Rename Channel Delete Channel Sort Method EPG (Electronic Program Guide) TIMER ANTENNA DIRECTION HELP GAME RECEIVER INFORMATION FRONT PANEL DISPLAY TROUBLE SHOOTING SYSTEM SPECIFICATION 31 31 32 32 33 33 34 34 GENERAL FUNCTION Select Channel Pause the Frame Previous Channel Recall TV&Radio mode TV&VCR mode Channel Information Volume&Audio Control Position 27 27 28 28 28 28 29 29 30 GENERAL INFORMATION Main Feature For your Safety Unpacking General Operation Remote Control Unit Front Panel Rear Panel INSTALLATION Connecting to Antenna & TV Connecting to TV using RF support Connecting to TV using RCA support Connecting to TV using Component Connecting to Digital Amplifier INSTALLATION WIZARD MAIN PAGE USER INSTALLATION Antenna setup - 1) DiSEqC 1.2 Antenna setup - 2) Fixed Antenna setup – 3) USALS Channel search -1) DiSEqC 1.2 Channel search -2) Fixed Channel search – 3) USALS Multi-SAT Search System setting Parental Lock Factory Default 4 4 5 6 6 7 8 9 10 10 10 11 11 12 Page 35 36 37 39 38 39 40 42 5 A XTC 5000 is a convenient product that allows you to view a variety of programs provided through satellite. This user’s guide covers the installation of the XTC 5000 and the necessary steps to implement various features. This also explains special features available only in this XTC 5000in detail, which will allow you to make full of these feature. Main Feature • Fully MPEG2, DVB compliant • PIG (Picture In Graphic) support • Provide friendly and easy-to-use menu system • Various channel editing function (favorite, moving, locking, renaming, deleting and sorting) • Stores up to 5000 channels • Easy and speedy software upgrade through RS-232 port • Plug-and-play data transfer system (Receiver to Receiver) • Timer function, automatically turns On/Off by setting function (daily, weekly, monthly and one time) • Automatic reserved channel moving system • Provide Electronic Program Guide (EPG) • Antenna positioning help feature • Digital Audio with AC-3 support by SPDIF • More than 800 pages OSD Teletext (DVB ETS 300 706) and Subtitle function support • Support for various video output : CVBS, S-VHS, YUV • 256 colors On-Screen-Display • PAL/NTSC automatically conversion • Last channel automatically…

Text truncated - open the document above for the full version.

23 1) Antenna: Select your antenna number. Channel Search-3) USALS 2) Satellite: Select a desired satellite using keys or if you press OKkey, the list of satellite will be displayed so that you can select easily. You can see the information of selected satellite in the right side. 4) ~ 9)Please refer to DiSEqC 1.2 type antenna. USER INSTALLATION After searching for SATELLITE 1, choose another satellite on the CHANNEL SEARCH screen. It will automatically locate the satellite and search for SIGNAL to start channel searching. ●Edit(Edit Mode): Please press ●Edit key on the RCU to display the sub-command box and edit the pre-programmed data such as Frequency, Symborate, Polarization, 22KHz. You can also use “Delete TP” & “Rename SAT” as well in this Edit Mode. ●Re-Sync When all location of searched satellites are shifted by unknown reason, you can realign all of them at once if you adjust one satellite’s location. ★Short-Cut Color Keys ★ 24 MultiSAT Search USER INSTALLATION XTC 5000 enables end users to have a multi- SAT search in each antenna type such as Fixed, DiSEqC1.2 and DiSEqC1.3. After all the necessary antenna set-up, simply press ●CH Search/ Advance key to open a search options. You can choose one of the options and press SEARCHand you are automatically moved to multi-sat search box and you can choose all the satellites you are searching for. ●Edit(Edit Mode): Please press ●Edit key on the RCU to display the sub-command box and edit the pre- programmed data such as Frequency, Symborate, Polarization, 22KHz. You can also use “Delete TP” & “Rename SAT” as well in this Edit Mode. ●Re-Sync When all location of searched satellites are shifted by unknown reason, you can realign all of them at once if you adjust one satellite’s location. ★Short-Cut Color Keys ★ 25 USER INSTALLATION System Setting System Setting menu allows you to change the the principal option and to set other items proper to your environment by pressing OK key on the RCU. 1) OSD Language: Select your desired OSD Language. 2) Audio Language: Select your desired audio language to be in the top priority under the condition that this language is supported from the channel. 3) Subtitle Language: Select your desired Subtitle Language. 4) LNB power: The default value of LNB power is ON. Select Off in the case of the LNB power is not necessary. 5) Screen Format: If your TV supports 16:9 screen format and selected channel provides 16:9 format program, select 16:9. 6) TV type: Select the type according to your TV type. 7) Display Info Bar: You can select the second Info Bar displayed on the screen. 8) Start On Channel: If you press OKkey, then the channel list is displayed. You can select one channel of the list, the selected channel starts whenever you turn on AD- 9700 PLUS. 9) DiSEqC Repeat: Select your DiSEqC . 26 Parent Lock This function allows you to lock the channel with your password in order to prevent from accessing the channel by your children or any other person. And also you can protect your installed data and information using Install Lock. ★How to change Password 1) Enter the current password. 2) Select ON of Parent Lock. 3) Enter new password. 4) Confirm your new password entering new password again. Note: Default password is 0000. Warning: Do not forget your password in order not to fail to view the channel. USER INSTALLATION 27 1) Enter the current password. 2) Select ON of Install Lock 3) Enter new password 4) Confirm your new password entering new password again 5) Exit this menu and Turn off the AD-9700 PLUS. 6) Turn on DSR 6500 GOLDand press MENU key on the RCU 7) Select any menu and press OK. 8) Then Enter Password Box will be displayed. 9) Unless enter correct password, you can not run any menu. Note: Default password is 0000 Warning: Do not forget your password in order not to fail to operate DVB-S CX ★How to use Install Lock Factory Default If you want to bring DSR 6500 GOLDback to the factory default condition, select Factory Default and press OKkey. Then Warning message will be displayed. To confirm select OK and press OK key. Warning: You will lose all of data and information which was installed. USER INSTALLATION Note: To activate Parent Lock, you have to turn off DSR 6500 GOLDonce. And turn on the DSR 6500 GOLDand select channel which is locked. Then enter your password. ★How to use Parent Lock 1) If you activate parent lock function, go to the TV channel Manager Page. 2) Press Open command box and select Lock 3) Select channel the which you want to Lock 4) Press OK then symbol is marked. 5) Exit this menu and Turn off the AD-9700 PLUS 28 If you want to select channel, use CH key on the front panel, PR+, PR- key on the RCU or numeric key on the RCU to select a channel and press OK key on the RCU. In addition to the above normal function, XTC 5000 provides more convenient channel change function. While watching, press OK/LIST key on the RCU or front panel. Then channel list will be displayed on the screen. If press EXIT key, the channel list will be disappeared. You can sort channel list by All, Favorite group, Satellite, Alphabet, CAS as follows. 1) All: It shows you all channel list sort by alphabet. 2) Favorite group: You can make favorite group in the menu of channel manager. It shows that group, and you can select one favorite group, then channel list belongs that group will be displayed. 3) Satellite: If you select ‘Satellite’, the list of satellite searched in DSR 6500 GOLDwill be displayed. Then you can select satellite you want. After that, you can see channel list belongs to the satellite. 4) Alphabet: If you select A or B... channel list(head of channel name A or B...) will be displayed. The following describes the basic functions of your XTC 5000 while watching satellite TV or listening to satellite radio. XTC 5000enables you to watch various scrambled channels by inserting the Smartcards according to your choice. While watching, the current channel information will be shown on the bott…

Text truncated - open the document above for the full version.

34 In Main Page, press ●Editkey on the RCU, and then select Rename CH on the command menu. This Rename CH command allow you to rename the channel. First select the channel, which you want to lock, pressing OK key and then Keypad Dialog Box will be displayed. Edit your desired name entering word or number. (If you select ◀, it deletes the previous word) And check whether the channel name is changed on channel list. Lock Channel Rename Channel CHANNEL MANAGER In Main Page, press ●SORTkey on the RCU, and then select Lock on the command menu. This Lock command allow you to lock the channel. First select the channel, which you want to lock, pressing OK key and then will be marked at rear of your selected channel name. Note : To perform this function, you should set up the Parent Lock which is explained after. 35 In Main Page, press ●SORTkey on the RCU, and Sort Method will be displayed. This Sort method has 4 sub commands and it allows you to sort the channels as provided. You can sort the channels by Lock, Scramble, SAT name and CH name. Place the cursor on your desired line, and then press OK key. And check whether the channels are sorted exiting on the channel list. Delete channel In Main Page, press ●Editkey on the RCU, and then select Delete on the command menu. This Delete command allows you to delete the channel permanently. First select the channels, which you want to delete, then selected channel number will be changed to If you cancel the selection, press OK key again, then the number will be back as it was If you decided to delete, press EXIT key and then Message box will be displayed. Press OK to delete. And check whether the channel number is changed exiting on channel list. Warning: The deleted channel can not be recovered unless you search again. Please be careful when you decide to delete channel. Sort Method Note : Radio Channel Manager is same operation as TV channel Manager. CHANNEL MANAGER 36 XTC 5000 provides EPG function for you to get access to the TV Guide(or Radio Guide if you are listening to radio channels) which will give the titles of the current and next programs on different channels. The information is only available from the network to which the channel you are watching belongs. Press EPG key on your RCU or select Program Guide in the Main Page. Two different types of EPG available, which is GRID EPG and Weekly EPG You can see the channel list in the left side and Program schedule for selected channel will be displayed in the right side. The time will be displayed relating to the program schedule. Select one channel and placing the “▼”mark on the time of Program name which detail information you want to know. Then you can see the program changes blue color. And press OK key, then detail information box will be displayed. Note: A ‘No data available” message will be shown if the selected channel does not provide EPG date. ELECTRONIC PROGRAM GUIDE (EPG) 37 The “TIMER” function allows you program the timer with various ways. This function is one of the strong point of XTC 5000 To activate the “Turn on time” and/or “Turn Off the time”, Select YES and enter your desired time. Note: The XTC 5000 display the time which is given by Satellite, so it may be a some differences between actual time and XTC 5000’s time. Time Adjust To activate the “Turn on time” and/or “Turn Off the time”, select YES and enter your desired time. And you can also select channel which will be turn on or turn off. Time Reservation Time Reservation allows you to program the various timer function. You can set the timer daily, weekly, monthly and yearly Note: Easy timer is default for the first time. TIMER 38 Although you entered correct value in Antenna Set up menu, if your antenna is positioned incorrectly, you could not receive signal form the Satellite. So XTC 5000 provides Antenna Direction Help in order for you to have exact information for the pointing of your antenna. First select your desired Satellite name and then the location of selected satellite will be displayed. In case of that the location of the satellite is changed, you can re-set up the new location. Second, enter the value of Longitude and Latitude of your location. If you entered correct value of your position, place your cursor on Compute and press OK key. Then XTC 5000 show the exact information of antenna pointing. ANTENNA DIRECTION HELP 39 GAME GAME XTC 5000 provides you with three different types of very exciting video games. The video games are simply available at the sub-menu of the main menu “Utility”. The available games are, 1)SNAKE 2)MINE SWEEPER 3)CRAZY TETRIS 40 : UP LOAD PROCEDURE : DOWN LOAD PROCEDURE : ERROR IN DATA TRANSMITTING : TV MODE : VCR MODE : SYSTEM WAITTING : FLASH ROM ERROR : SYSTEM BOOTING In the Receiver Information, you can show the information of the product, its version and contact point of supplier. If you have a problem on this products and any question, please feel free to contact the supplier which contact point is mentioned in this Receiver Information. RECEIVER INFO & FRONT PANEL DISPLAY Receiver Information Front Panel Display 41 ProblemPossible causesWhat to do The display on the front panel does not light up. Main cable is not connected.Check that the main cable is plugged into the power socket. No sound or picture, but the front panel shows red light. The XTC 5000 is in standby mode. Press the standby button. No sound or picture.The satellite dish is not pointing at the satellite. Adjust the dish. Check the signal level in the Antenna Setup menu. No signal or weak signal. Check the cable connections, LNB and other equipment connected between the LNB and the receiver, or adjust the dish. Bad picture / blocking error.The satellite dish is not pointing at the satellite. Adjust the dish. Signal is too strong.Connect a signal attenuator to the LNB input. Satellite dish is too small.Change to a larger dish. LNB noise factor too high.Change to an LNB with lower noise factor. The LNB is faul…

Text truncated - open the document above for the full version.

Appendix A. FCC ID Label and Location Report no. ETLE060201.037, Page 1 of 2 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Product Label Sample with FCC Label information Following is a sample copy of the label that will be placed on the rear cabinet of the product. The FCC ID Label and compliance statement are marked in the product label. XTC MOTORSPORTS INC. Digital Satellite Receiver FCC ID : TYV-XTC5000 Model No : XTC 5000 POWER : AC 90 – 250 V 50/60 Hz, Max. 35 W Serial No : N/A This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation Made in Canada Appendix A. FCC ID Label and Location Report no. ETLE060201.037, Page 2 of 2 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase.(Labeling requirements per 2.925) Label here

Appendix D. Internal Photographs Report no. ETLE060201.037, Page 1 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Inside View of The EUT Appendix D. Internal Photographs Report no. ETLE060201.037, Page 2 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Component side view of Main board Appendix D. Internal Photographs Report no. ETLE060201.037, Page 3 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Solder side view of Main board Appendix D. Internal Photographs Report no. ETLE060201.037, Page 4 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Inside View of The LNB TUNER Appendix D. Internal Photographs Report no. ETLE060201.037, Page 5 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Component side view of Power board Appendix D. Internal Photographs Report no. ETLE060201.037, Page 6 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Solder side view of Power board Appendix D. Internal Photographs Report no. ETLE060201.037, Page 7 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Component side view of Front Board Solder side view of Front Board Appendix D. Internal Photographs Report no. ETLE060201.037, Page 8 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 Inside View of The EUT of RF Modulator Appendix D. Internal Photographs Report no. ETLE060201.037, Page 9 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 View of Bottom cover View of Top cover Appendix D. Internal Photographs Report no. ETLE060201.037, Page 10 of 10 Head Office : # 371-51 Kasan-Dong, Keumcheon-ku, Seoul, 153-803, Korea Tel : 82-2-858-0786 Fax : 82-2-858-0788 EMC Lab : #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel:82-31-885-0072, Fax:82-31-885-0074 ETLQP-21-F22-0 View of Front Cover

Confidential (as of MAR 2, 2006) A. General features • Fully MPEG2, DVB compliant • 44 Hours recording with built in 80GB HDD (Hard Disk Drive) in 4Mbps stream • Within the same TP it is possible to record one channel and view another channel• At the time of watching the live mode, pre-recording motion by time-shift default supported • Automatic restoration ability for all files that were in process of recording at the time of an electricity failure• Recording current program while playing back earlier program simultaneously • Recording reservation function on Timer and EPG • Recording and playback with time delay (Time-Shift function) • 3 steps (x4, x8, x16) Fastforward and Rewind function • Pause and step playback function • HDD management function (Play, Move, Lock, Rename, Delete, Format) • Various playback function (Jump, Repeat, Shuffle, Slow playback) • Digital Audio with AC-3 support by SPDIF • PIG (Picture In Graphic) support • Provide friendly and easy-to-use menu system • Various channel editing function (favorite, moving, locking, renaming, deleting and sorting) • Stores up to 5000 channels • Easy and speedy software upgrade through RS-232 port • Plug-and-play data transfer system (DSR to DSR) • Timer function, automatically turns On/Off by setting function (daily, weekly, monthly and one time) • Automatic reserved channel moving system Engineering Specifications for XTC 5000 XTC MOTORSPORTS INC. XTC 5000 Engineering Specifications • Provide Electronic Program Guide (EPG) • More than 800 pages OSD Teletext (DVB ETS 300 706) and Subtitle function support • Support for various video output : CVBS, S-VHS, YUV • 256 colors On-Screen-Display • PAL/NTSC automatically conversion • Last channel automatically saving B. Engineering Specifications 1. Front-End 1-1. LNB & Tuner Input Input frequency : 950 to 2150 Mhz Digital signal input level : -65 to -25 dBm LNB supply : 13.5±0.5V / 18.5±0.7V, max.500mA Band switch control : 22KHz (Microprocessor control) Connector : 2 x F-Type, 3/8-32UNEF-2A (1 Input / 1 Loop through) 1-2. Demodulator Demodulation type : QPSK demodulation and FEC decoding in accordance with DVB prETS 300 421 Symbol rate (Rs) : 2 < Rs < 45 Mbaud SCPC and MCPC capable 2. Demultiplexing In accordance with ISO 13818-1. Simultaneous access will occur for the following : - 1 video stream of data rate up to 15 Mbits/s - 1 audio stereo/mono stream of data rate up to 448 kbits/s 32 PIDs Supported 3. Video Processing Decompression : MPEG-2 Main Profile @ Main Level With Letter Box filter Video buffer : 64 Mbits of SDRAM is provided Data rate : up to 15Mbits/s (Max. burst rate : 228 Mbits/s) Video output : PAL-25 frame @720 x 576 NTSC-30 frame @720 x 480 Video format : 4:3, 16:9 4. Audio Processing Decompression : MPEG-1 layer I and II, Musicam Outputs : Stereo Channel Dual MonoJoint Stereo ChannelMonoSpdif with AC-3 5. Baseband Inputs / Outputs 5-1. Baseband Video Video format : CVBS Output impedance : 75 Ω unbalanced Bandwidth : 5MHz Connector type : 1 x RCA 5-2. Baseband Audio Outputs Connector type : 2 x RCA (Left and Right) Output impedance : 600 Ω unbalanced Level : 0.6V rms±2dB into 10k Ω 5-3. Digital Audio Output Connector type : 1 x Optic Output type : Spdif encoded signals with ac-3 Sampling frequency rate : 32 , 44.1 or 48khz 5-4. S-VHS Output Video format : Y,C Output impedance : 75 Ω unbalanced Bandwidth : 5MHz Connector type : 1 x 4pin DIN 5-5. Component Outputs (YUV) Connector type : 3 x RCA (Y Pb Pr) Output impedance : 75 Ω unbalanced 6. Supply voltage to LNB Voltage supply path : DC supplied from DSR on LNB coax cable LNB type supported : LNB with integrated polarizer switch LNB supply voltage : (software selectable) . Vertical polarization : 13.5±0.5V DC . Horizontal polarization : 18.5±0.7V DC FSS/BSS Switching : A 22kHz±4kHz microprocessor controlled switching signal is provided Short circuit limit : 500mA 7. External Switched 12V Software switchable : 12V or 0V Current limit : 100mA Connector type : 1 x RCA 8. Data Service Port Connector : 9-pin D-sub male Data protocol : RS232C interface The DVB-DSR is seen as the DataCommunication Equipment (DCE)and the PC (or other terminal) is seenas the Data Terminal Equipment (DTE). Data rate : Maximum of 625K bits/s Pin Name Source 2 RXD PC 3 TXD Transmit data DSR 5 GND Signal ground 9. Microprocessor Microprocessor : SGS-Thomson Sti5518 Clock frequency : 81MHz SDRAM Memory : 8Mbyte Flash memory : 2Mbyte 10. RF Modulator RF Output Signal : NTSC M Receive data Function Video Carrier Frequency : 61.25 ± 90 ㎑ US 3 CH 67.25 ± 90 ㎑ US 4 CH 11. Built-in HDD Formatted Gbyte : 80Gbytes Interface : Ultra ATA/66 Spindle speed : 5,400 RPM 12. Remote Control unit Number of keys : 41 Keys Operating distance : up to 10m Batterys : 2 x 1.5V (AAA type) 13. Power Supply Type : Switching mode Main input voltage : 90 - 250V AC @ 50Hz/60Hz±5% Nominal power consumption : 27W Standby power consumption : 7W Typical supply currents - +3.3V : 0.9A - +5.0V : 0.4A - +7.0V : 0.27A - +12V : 0.03A - +22V : 0.4A - +30V : 0.03A - +12V HDD : 0.45A - +5V HDD : 0.5A 14. Physical Characteristics 14-1. Front Panel Keys : 8 Keys Indicators : Power on/off Remote control input : Infra-red receiver Display : 4Digit (7Segment) 14-2. Rear Panel Connectors : 1 LNB Input / 1 Loop through output (2F-type : IEC169-24) 1 x 0/12 Volt (RCA)2 x Audio L/R (RCA)1 x CVBS (RCA)3 x YUV (RCA)1 x RS-232 (9-pin D-sub male)1 x RF Modulator (2F-type : IEC169-24)1 x S-VHS (4-pin Mini-Din)1 x Digital Audio Output (optic) Switch : 1 x AC Power Switch NOTE) The above specification is subject to be changed without notice in advance.

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the ETL,Inc. www.etl.re.kr E-RAE Testing Laboratory Electromagnetic Emission FCC MEASUREMENT REPORT CERTIFICATION OF COMPLIANCE FCC Part 15 Certification Measurement T his Digital Satellite Receiver, Model XTC 5000 has been tested in accordance with the measurement procedures specified in ANSI C63.4-2003 at the ETL/EMC Test Laboratory and has been shown to complied with the electromagnetic radiated emission limits specified in FCC Rule Part15 Subpart B: TV interface device. I attest to the accuracy of data. All measurement here in was performed by me or was made under my supervision and is correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. The results of testing in this report apply to the product/system, which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Hyung Seok, Lee / Chief Engineer ETL Inc. #584 Sangwhal-ri, Kanam-myon, Yoju-kun, Kyounggi-do, 469-885, Korea Tel : (031) 885-0072 Fax : (031) 885-0074 PRODUCT : Digital Satellite Receiver MODEL/TYPE NO : XTC 5000 FCC ID : TYV-XTC5000 AP…

Text truncated - open the document above for the full version.