U2ZZW3012Z-Wave 700s In-Wall No Neutral Dimmer

Tools you will need Fr Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils exempts de licence d’Industrie Canada. Son utilisation est sujette aux deux conditions suivantes : (1) cet appareil ne doit pas occasionner de brouillage préjudiciable et (2) cet appareil doit accepter toutes les interférences reçues, notamment les interférences qui peuvent provoquer un fonctionnement non désiré. NOTE DE LA FCC : Le fabricant n’est pas responsable des interférences sur les fréquences radioélectriques ou télévisuelles pouvant être causées par des modifications non autorisées de ce matériel. De telles modifications peuvent annuler le droit de l’utilisateur à utiliser cet appareil. REMARQUE : Cet appareil a été testé et certifié conforme aux limites relatives aux appareils numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites ont été définies afin de fournir une protection raisonnable contre le brouillage préjudiciable en milieu résidentiel. Cet appareil produit, utilise et peut émettre des ondes de fréquence radio et, s’il n’est pas installé et utilisé conformément aux instructions, il peut provoquer un brouillage préjudiciable aux communications radio. Il n’existe toutefois aucune garantie que des interférences ne se produiront pas au sein d’une installation donnée. Si cet appareil occasionne un brouillage préjudiciable à la réception radiophonique ou télévisuelle, il suffit d’allumer et d’éteindre l’appareil pour déterminer sa responsabilité. Nous encourageons l’utilisateur à essayer de corriger ces interférences en appliquant une ou plusieurs des mesures suivantes : — Réorienter ou déplacer l’antenne de réception. — Augmenter la distance entre l’appareil et le récepteur. — Brancher l’appareil à une prise secteur différente de celle du récepteur. — Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs. Remarque importante : Pour se conformer aux exigences de conformité de la FCC concernant l’exposition aux RF, aucune modification apportée à l’antenne ou au dispositif n’est autorisée. Toute modification apportée à l’antenne ou au dispositif pourrait faire en sorte que le dispositif dépasse les exigences d’exposition aux RF et pourrait annuler le droit de l’utilisateur à utiliser ce dispositif. En This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. Es Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC y con las especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria de Canadá aplicables a aparatos exentos de licencia. El funcionamiento está sujeto a las siguientes dos condiciones: (1) este dispositivo no debe provocar interferencia perjudicial, y (2) este dispositivo debe aceptar toda interferencia que reciba, incluso la que pudiera causar un funcionamiento no deseado. NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas modificaciones podrían anular la autoridad del usuario para utilizar el equipo. NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de Clase B, de conformidad con el apartado 15 de las normas de la FCC. Estos límites están diseñados para proveer protección razonable contra interferencias perjudiciales en una instalación residencial. Este equipo genera, usa y puede irradiar energía de radiofrecuencias y, si no se instala y usa según las instrucciones, puede provocar interferencia perjudicial a las radiocomunicaciones. No obstante, no hay garantías de que no ocurrirá interferencia en una instalación en particular. Si este equipo provoca interferencia perjudicial a la recepción de radio o televisión, lo que puede determinarse encendiendo y apagando el equipo, se recomienda que el usuario intente corregir la interferencia por medio de la implementación de una o más de las siguientes medidas: — Reorientar o reubicar la antena receptora. — Incrementar la separación entre el equipo y el receptor. — Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que está conectado el rece…

Text truncated - open the document above for the full version.

Sheenway Asia Ltd Room 1313, 13/F, Austin Tower, Tsim Sha Tsui, Kowloon. Tel (86-755)82374246 Fax (86-755)82375277 Email: [email protected] Date: 07/22/2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize of Shenzhen Academy of Metrology and Quality Inspection and hereafter referred to as SMQ, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by of Shenzhen Academy of Metrology and Quality Inspection on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing SMQ as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Sammel Tung, Manager Sheenway Asia Ltd REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

Sheenway Asia Ltd Room 1313, 13/F, Austin Tower, Tsim Sha Tsui, Kowloon. Tel (86-755)82374246 Fax (86-755)82375277 Email: [email protected] Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: U2ZZW3012 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Sammel Tung Manager Sheenway Asia Ltd August, 14, 2020

Photo 1 Appearance of EUT Photo 2 Appearance of EUT Photo 3 Appearance of EUT Photo 4 Appearance of EUT Photo 5 Appearance of EUT Photo 6 Appearance of EUT

3MWZ Pour utilisation intérieure uniquement. Sert à commander des appareils à DEL, CFL, incandescence installés de façon permanente seulement. For indoor use only. For control of permanently installed LED, CFL, incandescent and halogen fixtures only. ZW3012 Pendentif Traveler Secteur/Charge Line/Load Ter re Ground Secteur/Charge Line/Load Dimmer Switch Interrupteur gradateur 120VAC/120VCA 60Hz 600W2-gang 500W2 compartiments 500W3-gang 400W3 compartiments 400W300W dimmable CFL/LED300W gradateur CFL/DELOperating temp. 32–104° FTempérature de service 0–40° C Jasco Products Company Oklahoma City, OK www.byjasco.com Made in China/ Fabriqué en Chine 52253-1 In-Wall Smart Dimmer Interrupteur intelligent mural MODEL: ZW3012 Type 1 enclosure Boîtier de type 1 FCC ID: U2ZZW3012 IC: 6924A-ZW3012 VER 5.4 CAUTION/ ADVERTENCIA HIGH VOLTAGE, DISCONNECT POWER SUPPLY BEFORE SERVICING/ALTO VOLTAJE, DESCONECTE LA POTENCIA ANTES DE REPARAR NEW ART PMS 430C ENGRAVINGSILKSCREEN Enclosure & Yoke Pad printing specifications for: Z-Wave product, Jasco Model no: ZW3012 / 52253 52253 Enclosure v1 Paul Milligan 04/17/20 Matt Henson 105.008 mm 60.007 mm 45.191 mm PRODUCT MARKINGS: 13.671 MM 11 MM S2 QR code 13.69mm

Photo 1 Inside of EUT Photo 2 Inside of EUT Photo 3 Inside of EUT Photo 4 Inside of EUT

Report No.: WT208001460 Page 1/24 FCC TEST REPORT For Z-Wave 700s In-Wall No Neutral Dimmer Model Number: ZW3012 FCC ID: U2ZZW3012 Report Number : WT208001460 Test Laboratory : Shenzhen Academy of Metrology and Quality Inspection Site Location : NETC Building, No.4 Tongfa Rd., Xili, Nanshan, Shenzhen, China Tel : 0086-755-86928965 Fax : 0086-755-86009898-31396 Web : www.smq.com.cn Email : [email protected] Report No.: WT208001460 Page 2/24 Test report declaration Applicant : SHEENWAY ASIA LTD. Address : Room1313, 13/F, Austin Tower, 22-26 Austin Avenue, Tsim Sha Tsui, Kowloon, Hong Kong, China Manufacturer : SHEENWAY ASIA LTD. Address : Room1313, 13/F, Austin Tower, 22-26 Austin Avenue, Tsim Sha Tsui, Kowloon, Hong Kong, China EUT Description : Z-Wave 700s In-Wall No Neutral Dimmer Model No. : ZW3012 FCC ID : U2ZZW3012 Test Standards: FCC Part 15 (October 1, 2019 Edition) ANSI C63.10-2013 The EUT described above is tested by Shenzhen Academy of Metrology and Quality Inspection EMC Laboratory to determine the maximum emissions from the EUT. Shenzhen Academy of Metrology and Quality Inspection EMC Laboratory is assumed full responsibility for the accuracy of the test results. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 and the energy emitted by the sample EUT tested as described in this report is in compliance with FCC Rules Part 15.249. The test report is valid for above tested sample only and shall not be reproduced in part without written approval of the laboratory. Project Engineer: Date: Sep.17, 2020 (Zhou Fangai ) Sep.17, 2020 Checked by: Date: (Lin Yixiang) Sep.17, 2020 Approved by: Date: (Lin Bin) Report No.: WT208001460 Page 3/24 TABLE OF CONTENTS TEST REPORT DECLARATION ............................................................................................. 2 1. TEST RESULTS SUMMARY ........................................................................................ 4 2. GENERAL INFORMATION ........................................................................................... 5 2.1. Report information .............................................................................................. 5 2.2. Laboratory Accreditation and Relationship to Customer .................................... 5 2.3. Measurement Uncertainty .................................................................................. 6 3. PRODUCT DESCRIPTION ........................................................................................... 7 3.1. EUT Description ................................................................................................. 7 3.2. Block Diagram of EUT Configuration ................................................................. 7 3.3. Operating Condition of EUT ............................................................................... 7 3.4. Special Accessories ........................................................................................... 7 3.5. Equipment Modifications .................................................................................... 7 3.6. Support Equipment List ...................................................................................... 7 3.7. Test Conditions .................................................................................................. 7 4. TEST EQUIPMENT USED ............................................................................................ 8 5. CONDUCTED EMISSION TEST ................................................................................... 9 5.1. Test Standard and Limit ..................................................................................... 9 5.2. Test Procedure ................................................................................................... 9 5.3. Test Arrangement .............................................................................................. 9 5.4. Test Data ............................................................................................................ 9 6. RADIATED EMISSION TEST ..................................................................................... 12 6.1. Test Standard and Limit ................................................................................... 12 6.2. Test Procedure ................................................................................................. 12 6.3. Test Arrangement ............................................................................................ 12 6.4. Test Data .......................................................................................................... 13 7. OCCUPIED BANDWIDTH .......................................................................................... 20 7.1. Test Standard and Limit ................................................................................... 20 7.2. Test Procedure ................................................................................................. 20 7.3. Test Arrangement ............................................................................................ 20 7.4. Test Data .......................................................................................................... 20 8. BAND EDGE ............................................................................................................... 22 8.1. Test Standard and Limit ................................................................................... 22 8.2. Band Edge FCC 15.249(d) Limit ...................................................................... 22 8.3. Test Procedure ................................................................................................. 22 8.4. Test Arrangement ............................................................................................ 22 8.5. Test Data ..................................................................…

Text truncated - open the document above for the full version.

Report No.: WT208001460 Page 1/24 FCC TEST REPORT For Z-Wave 700s In-Wall No Neutral Dimmer Model Number: ZW3012 FCC ID: U2ZZW3012 Report Number : WT208001460 Test Laboratory : Shenzhen Academy of Metrology and Quality Inspection Site Location : NETC Building, No.4 Tongfa Rd., Xili, Nanshan, Shenzhen, China Tel : 0086-755-86928965 Fax : 0086-755-86009898-31396 Web : www.smq.com.cn Email : [email protected] Report No.: WT208001460 Page 2/24 Test report declaration Applicant : SHEENWAY ASIA LTD. Address : Room1313, 13/F, Austin Tower, 22-26 Austin Avenue, Tsim Sha Tsui, Kowloon, Hong Kong, China Manufacturer : SHEENWAY ASIA LTD. Address : Room1313, 13/F, Austin Tower, 22-26 Austin Avenue, Tsim Sha Tsui, Kowloon, Hong Kong, China EUT Description : Z-Wave 700s In-Wall No Neutral Dimmer Model No. : ZW3012 FCC ID : U2ZZW3012 Test Standards: FCC Part 15 (October 1, 2019 Edition) ANSI C63.10-2013 The EUT described above is tested by Shenzhen Academy of Metrology and Quality Inspection EMC Laboratory to determine the maximum emissions from the EUT. Shenzhen Academy of Metrology and Quality Inspection EMC Laboratory is assumed full responsibility for the accuracy of the test results. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 and the energy emitted by the sample EUT tested as described in this report is in compliance with FCC Rules Part 15.249. The test report is valid for above tested sample only and shall not be reproduced in part without written approval of the laboratory. Project Engineer: Date: Sep.17, 2020 (Zhou Fangai ) Sep.17, 2020 Checked by: Date: (Lin Yixiang) Sep.17, 2020 Approved by: Date: (Lin Bin) Report No.: WT208001460 Page 3/24 TABLE OF CONTENTS TEST REPORT DECLARATION ............................................................................................. 2 1. TEST RESULTS SUMMARY ........................................................................................ 4 2. GENERAL INFORMATION ........................................................................................... 5 2.1. Report information .............................................................................................. 5 2.2. Laboratory Accreditation and Relationship to Customer .................................... 5 2.3. Measurement Uncertainty .................................................................................. 6 3. PRODUCT DESCRIPTION ........................................................................................... 7 3.1. EUT Description ................................................................................................. 7 3.2. Block Diagram of EUT Configuration ................................................................. 7 3.3. Operating Condition of EUT ............................................................................... 7 3.4. Special Accessories ........................................................................................... 7 3.5. Equipment Modifications .................................................................................... 7 3.6. Support Equipment List ...................................................................................... 7 3.7. Test Conditions .................................................................................................. 7 4. TEST EQUIPMENT USED ............................................................................................ 8 5. CONDUCTED EMISSION TEST ................................................................................... 9 5.1. Test Standard and Limit ..................................................................................... 9 5.2. Test Procedure ................................................................................................... 9 5.3. Test Arrangement .............................................................................................. 9 5.4. Test Data ............................................................................................................ 9 6. RADIATED EMISSION TEST ..................................................................................... 12 6.1. Test Standard and Limit ................................................................................... 12 6.2. Test Procedure ................................................................................................. 12 6.3. Test Arrangement ............................................................................................ 12 6.4. Test Data .......................................................................................................... 13 7. OCCUPIED BANDWIDTH .......................................................................................... 20 7.1. Test Standard and Limit ................................................................................... 20 7.2. Test Procedure ................................................................................................. 20 7.3. Test Arrangement ............................................................................................ 20 7.4. Test Data .......................................................................................................... 20 8. BAND EDGE ............................................................................................................... 22 8.1. Test Standard and Limit ................................................................................... 22 8.2. Band Edge FCC 15.249(d) Limit ...................................................................... 22 8.3. Test Procedure ................................................................................................. 22 8.4. Test Arrangement ............................................................................................ 22 8.5. Test Data ..................................................................…

Text truncated - open the document above for the full version.