U59BCH-220Scanning Receiver

Content Brief Introduction Thank you for buying scanning receiver. The goal is to provide cost-effective communication equipment for a variety of business sites and the amateur and supply all fast-paced walks of life with perfect communication solutions. This product uses amateur frequency ,you need to apply for use to radio management institution of the provinces, cities or autonomous regions . please read this manual carefully in order to know how to properly operate the radio before use. Unpacking and Checking Equipment Welcome to use radios, before using we suggest you: ·Please check the packing box of this product and see if there are signs of damage. ·Please open the packing box carefully. We recommend that you identify the items listed in the following packing list. if you find that our product and its accessories in handling are lost or damaged during the shipment. Please immediately contact dealers. Parts List Item Quantity Rubber Antenna 1 Li-ion Battery Pack 1 Desktop Charger 1 Power Adapter 1 Belt Clip 1 User’s Manual 1 Warranty Card 1 Hand Strap 1 Preparation Charging the Battery 1. Using the battery The battery is not completely charged at the factory, please charge it before using. To extend the battery life time, please power off the battery when you don't use two way radio, and save battery in a cool (temperature less than 25 )and dry place.°C 2 Precautions of Charging Equipment 1. Do not expose the charger to rain or snow. 2. Do not operate the charger if it has received a sharp blow, or has been dropped or damaged in any way. 3. Do not disassemble the charger if it has received a sharp blow, or has been dropped or damaged in any way. 4. Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock. 5. To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle. 6. To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning. 7. Use of an attachment not recommended or sold by JUSTON may result in a risk of fire, electric shock, or personal injury. 8. Make sure the cord is located so it will not be stepped on, tripped over, or subjected to damage or stress. 9. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and/or electric shock. If an extension cord must be used, make sure that: •The pins on the plug of the extension cord are the same number, size, and shape as those on the plug of the charger. •The extension cord is properly wired and in good electrical condition. •The cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to 150feet. 10. Do not replace charger's power cord. If the power cord damages, you must stop using charger immediately. 3. Charging the Battery Please use the battery charger designated by to charge battery. After purchase or extended storage (more than two months), the first time to charge battery cannot make battery reach its normal operating capacity. After repeating charge /discharge it two or three times, the operating capacity will increase to its normal capacity. 4. Please Charge the Radio According to Operation Steps as Follows: 1. Insert power adapter into power supply socket. 2. Insert output terminal of power adapter into DC jack behind the charging kit, now the charging orange indicator lights about 2 seconds then goes out. 3. Insert the battery or radio equipped with battery into the charging kit. 4. Confirm the battery and charging kit terminal contact reliably, when charging indicator light turns into red and charging starts. 5. After completion of charge (charging time about 5 hours), light turns to be green. 5. Indicators Display As Following: Status Indicator Power Connected Orange light is on about 2 seconds then goes out No battery(temperature end judges) All go out Charge normally Red light is on The battery is fully charged Green light is on Fault (over temperature, battery short circuit or over discharge state) Red light flashes Note: Before charging, please turn off radio power equipped with battery. When charging, using radio will interfere with normal charge of battery and receiver effect. Basic operations  Power On/Off Turn the power switch knob clockwise to turn on radio power; to turn it off ,turn the power switch knob counter-clockwise.  Vo l u m e C o n t r o l Turn the volume switch knob clockwise to increase volume; to decrease the volume, rotate the volume switch knob counter-clockwise.  RX When radio receiving information ,green LED lights . 1) Only same signaling and CTCSS setting can receive information . 2) May not receive any calling if radio is at lower signal and set high level SQL. 3) Local dealer maybe program your radio with CTCSS/DCS . Users can receive the same signaling information if chosen channel with CTCSS/DCS . Or it can not get any calling . R a sp pr L 1 2 3 4 5 6 7 8 9 10 11 12 adio with CT pecial channel rogrammed th LCD Ico 0 1 2 CSS/DCS wi l for CTCSS/ he same CTC ons Inst Icon ill help you to /DCS ,radio a SS /DCS . truction ns o ignore ineff also can comm n fective calling municate with Inst Cha K F Na F Last Dig g. Although t h other radio tructions annel/Menu Key Lock DTMF DCS CTCSS Battery FM Radio arrow Band VOX Scan Function gits at Frequen there seems which ncy Program Settings Radio Basic Information 1) Frequency Please type in desired frequency value. 2) Back to factory default settings You can initialize factory default settings by program software. 3) Delete Channel Group You can delete the chosen channel by program software . 4) Turn On SP Turn on speaker, you can hear sound from radio when it receives correct signaling.  Optional Items 1)Alarm before TOT You can set an alert tone sounds fro…

Text truncated - open the document above for the full version.

Tekk International Inc. 1916 Linn St, North Kansas City, Missouri 64116, United States Tel: 816-746-1098 Fax: 866-884-3304 November 2, 2015 Federal Communications Commission Authorization and Evaluation Division, 7435 Oakland Mills Road Columbia, MD 21046 USA Re: BCH-220 (FCC ID: U59BCH-220) Gentlemen: The scanner receiver equipment meets the requirements of the FCC Rules, 15.121 (a). Compliance is achieved through the following methods: The scanner receiver in this equipment is incapable of tuning, or readily being altered, by the User to operate within the frequency bands allocated to the Domestic Public Cellular Telecommunications Service in Part 22. Blocking of the cellular frequencies is implemented in the firmware of the unit’s main control central processing unit (CPU). Coverage of 824 - 849 MHz and 869 - 894 MHz is completely blocked, since it is done in the microprocessor, and cannot be re-enabled by any user-accessible procedure, including diode, resistor, or jumper changes, nor by connection of any external device such as a personal computer, nor by installation of any “special” enabling semiconductor device. The scanning receiver is designed so that the tuning, control and filtering circuitry is inaccessible. Sincerely, Tekk International Inc. Signature: David Stubbs President

QA-FR-171-A Tekk International Inc. 1916 Linn St, North Kansas City, Missouri 64116, United States Tel: 816-746-1098 Fax: 866-884-3304 FCC Confidential Authorization 2015-9-30 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: U59BCH-220 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, (Tekk International Inc.) hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description  Internal photos The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, David Stubbs President

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT – All View EUT (Handset) – Front View EUT (Handset) – Rear View EUT (Handset) – Top View EUT (Handset) – Bottom View EUT (Handset) – Left Side View EUT (Handset) – Right Side View EUT (Base) – Front View EUT (Base) – Rear View EUT (Base) – Top View EUT (Base) – Bottom View EUT (Base) – Left Side View EUT (Base) – Right Side View EUT – Adapter View EUT – Tie View

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0 FCC PART 15B, CLASS B TEST REPORT For Tekk International Inc. 1916 Linn St, North Kansas City, Missouri 64116, United States Report Type: Original Report Product Type: Scanning Receiver Test En gineer: Liewei Liu Re port Number: RSZ150917028-00 Re port Date: 2015-09-30 Reviewed B y: Jimmy Xiao RF En gineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn FCC ID: U59BCH-220 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: RSZ150917028-00 FCC Part 15B, Class B Page 2 of 18 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 3 TEST METHODOLOGY .................................................................................................................................................. 3 TEST FACILITY ............................................................................................................................................................. 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 5 EUT EXERCISE SOFTWARE .......................................................................................................................................... 5 SPECIAL ACCESSORIES ................................................................................................................................................. 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 5 EXTERNAL I/O CABLE .................................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULTS ............................................................................................................................... 7 FCC §15.107 – AC LINE CONDUCTED EMISSIONS ............................................................................................. 8 APPLICABLE STANDARD .............................................................................................................................................. 8 MEASUREMENT UNCERTAINTY .................................................................................................................................... 8 EUT SETUP .................................................................................................................................................................. 8 EMI TEST RECEIVER SETUP ......................................................................................................................................... 9 TEST PROCEDURE ........................................................................................................................................................ 9 TEST EQUIPMENT LIST AND DETAILS ........................................................................................................................... 9 CORRECTED FACTOR & MARGIN CALCULATION ......................................................................................................... 9 TEST RESULTS SUMMARY .......................................................................................................................................... 10 TEST DATA ................................................................................................................................................................ 10 FCC §15.109 - RADIATED SPURIOUS EMISSIONS ............................................................................................ 13 APPLICABLE STANDARD ............................................................................................................................................ 13 MEASUREMENT UNCERTAINTY .................................................................................................................................. 13 EUT SETUP ................................................................................................................................................................ 13 EMI TEST RECEIVER SETUP ....................................................................................................................................... 14 TEST PROCEDURE ..................................................................................................................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions - Front View Conducted Emissions - Side View Radiated Emissions Test View (Below 1 GHz) Radiated Emissions View (Above 1 GHz)