U7NRDM530DESKTOP READER

RDM TAG MASTER CO.,LTD ·区区路201 TEL +86-755- 61313350 Fangda Building201,Keji 12 th Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China Http://www.datarfid.com [email protected] FAX+86-755- 61313357 RDM530 SERIAL Desktop Reader: ISO14443A/B, ISO15693 DEVELOPMENT KIT FCC NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 1 PS2 or RS232 or USB or TCP/IP OPERATIONS The RDM530 Desktop Reader which support ISO14443-A-B, ISO15693, can operate with a terminal such as computer or other controller, which can supply PS2 orRS232 or USB or TCP/IP interface and only supplied by computer or other controller. 1.1 Electrical Interface Basically, this communication protocol does not need to be bound with any electrical interface characteristic. Typically the following types of physical link could be used: • PS2 (Point to point only) • RS232 (Point to point only) • USB (Slave only) • TCP/IP(Slave only) 1.2 RS232 Data Format: 1.2.1 PC/SC Smart Card Reader with RS232 connection .Compliant with PC/SC V2.0 specifications. 1.2.2 RDM TAG MASTER DATA FORMAT:The data format (Start Bit, Data Bits, parity, Stop Bit) is software configurable, and can be set to match the special requirement of data transmission between two communication devices. The general data format is defined as: Parameter Description Baud Rate Selective: 9600, 19200, 38400, 57600, 1152000 (It can be changed by command Send from the Host) Data Bits Fixed: 8 bits Start Bit Fixed: 1 Bits Stop Bit Selective: 1 bit. Parity None RDM TAG MASTER CO.,LTD ·区区路201 TEL +86-755- 61313350 Fangda Building201,Keji 12 th Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China Http://www.datarfid.com [email protected] FAX+86-755- 61313357 The following is the default setting (RS232): Baud Rate Data Bits Start Bit Stop Bit Parity 9600 8 1 1 None 1.3 USB Data Format: PC/SC Smart Card Reader with USB connection .Compliant with PC/SC V2.0 specifications. RDM TAG MASTER CO.,LTD ·区区路201 TEL +86-755- 61313350 Fangda Building201,Keji 12 th Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China Http://www.datarfid.com [email protected] FAX+86-755- 61313357 2 Link Layer The communication protocol is a packet-oriented protocol - all the data exchanged between two communication devices will be based on packet format. The protocol is designed for multi-drop mode and where point-to-point mode could be treated as a special case of multi-drop mode. The data packet starts with the control character ‘STX’ and ends with ‘ETX’, which follows the 8-bit BCC checksum. Besides the checksum is used for error checking, character (byte) time-out and packet (command) time-out are used to re-synchronous the communication. 2.1 Packet Format There are two types of data packets. Command Message is the packet Send from the Host to the reader device. The Reply Message is the packet Send from the reader to the Host. Packet format for Command Message (Host to Reader) STX STATION ID DATA LENGTH CMDDATA[0..N] BCC ETX Packet format for Reply Message (Reader to Host) STX STATION ID DATA LENGTH STATUS DATA[0..N]BCC ETX RDM TAG MASTER CO.,LTD ·区区路201 TEL +86-755- 61313350 Fangda Building201,Keji 12 th Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China Http://www.datarfid.com [email protected] FAX+86-755- 61313357 3 Available Commands Name Description SYSTEM COMMANDS SetAddress Program the Device Address to the reader SetBaudrate Set the reader’s communication baud rate SetSerlNum Set the reader’s Serial Number GetSerNum Get the reader’s Serial Number SetUserInfo Set the Usr Information GetUserInfo Get the User Information GetVerNum Get the reader’s firmware version number. SetPort Control status of the I/O ports. SetLED Turn On/Off the LEDs SetBuzzer Turn On/Off the Buzzer Control-workmode Control the reader to stay in active state or idle state ISO14443-A-B COMMANDS REQA ISO14443A REQUEST Anticoll ISO14443A Anti-collision Select ISO14443A Select Halt ISO14443A Halt Request_B ISO14443B REQB command Attrib_B ISO14443B ATTRIB command RDM_Rst_ Typeb Integrate the request and attrib command RDM__Typeb_Trans fer_Command ISO14443-4 transparent command Type B Card MF_Read The Read command integrates the low level commands (request, anti- collision, select, authentication, read) to achieve the reading operation with a one-step single command. MF_Write The Write command integrates the low level commands (request, anti- collision, select, authentication, write) to achieve the writing operation RDM TAG MASTER CO.,LTD ·区区路201 TEL +86-755- 61313350 Fangda Building201,Keji 12 th Rood south, High-Tech Industrial Park, Nanshan Shenzhen, China Http://www.datarfid.com [email protected] FAX+86-755- 61313357 with a one-step single command. MF_InitVal The Initialization command integrates the low level commands (request, anti-collision, select, authentication) to achieve the value block initialization with a one-step single command. MF_Decrement The Decrement command integrates the low level commands (request, anti-collision, select, authentication) to achieve the Decrement with a one-step single command. MF_HLIncrement The Increment command integrates the low level commands (request, anti-collision, select, authentication) to achieve the Increment with a one-step single command. MF_GetSnr The GetSnr command integrates the low level commands (request,anticoll,select) to achieve the select card with a one-step single command,and output the card’s Snr ISO15693 COMMANDS RDM_Inventory ISO15693 Inventory Command RDM_Read ISO15…

Text truncated - open the document above for the full version.

SHENZHEN RDM TAG MASTER CO.,LTD. FCC ID: U7NRDM530 BT FCC ID REPORT :F07050829C General Appearance of the EUT General Appearance of the EUT(Bottom)

SHENZHEN RDM TAG MASTER CO.,LTD. FCC ID: U7NRDM530 BT FCC ID REPORT :F07050829C FCC ID LABEL FCC ID: U7NRDM530 Label Location on EUT EUT Bottom View/ FCC ID Label Location

SHENZHEN RDM TAG MASTER CO.,LTD. FCC ID: U7NRDM530 BT FCC ID REPORT :F07050829C FCC ID LABEL FCC ID: U7NRDM530 Label Location on EUT EUT Bottom View/ FCC ID Label Location

SHENZHEN RDM TAG MASTER CO.,LTD. FCC ID: U7NRDM530 BT FCC ID REPORT :F07050829C General Appearance of the EUT(Inside) General Appearance of the EUT(Inside) SHENZHEN RDM TAG MASTER CO.,LTD. FCC ID: U7NRDM530 BT FCC ID REPORT :F07050829C Mainboard & RF pcb of the EUT Mainboard & RF pcb of the EUT

Rdm530 Diagram Block Description The RDM530/RDM510/RDM520 Desktop Reader is a ISO14443 A,B and ISO15693, read/write device with a typical operating distance of 50-100mm. The RDM530/RDM510/RDM520 combines all basic functions to access the ISO14443A,B and ISO15693. Including Mifare® Smart Card, TI Card, EM Card etc. Its versatility allows a flexible and efficient application in different configurations and system devices. It can be integrated easily into existing data collection applications such as portable terminals, ticketing, machines vending or access control, etc... The RDM530/RDM510/RDM520 Desktop Reader was designed for simple integration. Which has supplied RS232, USB, PS2, TCP/IP interface (selected)can be directly connected to computer or other microcomputer. The protocol can be tested using any terminal. The RDM530/RDM510/RDM520 have USB or RS232 interface which compliant with PC/SC V2.0 specifications Basic principle description: According to ISO14443A/B, ISO15693 standard, the Microprocessor(U1) and Basic frequency(13.56MHz) state(X1) will generate a specific signal, Amplifer(U2) the signal and sending out through antenna circuitry. The ISO14443A/B, ISO15693 card will get a response information for identification while it approach the transmit antenna. The receiver circuitry part will be accepting & transform it, and inform the microcomputer as well. The microcomputer based on the set program to read & write the card to fulfill the specific function. The performance of specific program setting & function is fulfilled by interface circuitry. This could be done via the smart connection between interface circuitry & computer or others smart device. Interface could be RS232, USB, PS2, or TCP/IP. Status output indicated the status during the operation, the operation process could be monitor and show the operation is correct or not. Concluded above details for RDM530/RDM510/RDM520, the Desktop Reader with integrated function, fully compliance with ISO14443A/B,ISO15693 contactless card international standard for read & write.

新产品开发

FCC PART 15.225 EMI MEASUREMENT AND TEST REPORT For SHEN ZHEN RDM TAG MASTER CO.,LTD Fangda Building 207,Keji 12 th Road south,High-Tech Industrial Park, NanShan ShenZhen FCC ID: U7NRDM530 May.16,2007 This Report Concerns: Original Report Equipment Type RFID Module Test Engineer: Eric Li Report No.: F07050829C Receive EUT Date/Test Date: May 10,2007/ May 10-16,2007 Reviewed By: Christina Prepared By: Shenzhen Best Technology Co.,Ltd. 7/F,Jianda Bldg.,Keyuan Rd. North, Science Park,Nanshan, Shenzhen, China Tel: 0755-267477513 Fax: 0755-267477513 ext.826 Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of Shenzhen Best Technology Co.,Ltd. This report must not be used by the client to claim product certification,approval,or endorsement by NVLAP, NIST or any agency of the US Government. SHENZHEN RDM TAG MASTER CO.,LTD. FCC ID: U7NRDM530 BT FCC ID REPORT :F07050829C Page 2/26 TABLE OF CONTENTS 1. GENERAL INFORMATION ....................................................................................................4 1.1. Report information ............................................................................................................4 1.2. Measurement Uncertainty .................................................................................................4 2. PRODUCT DESCRIPTION ......................................................................................................5 2.1. EUT Description ...............................................................................................................5 2.2. Block Diagram of EUT Configuration..............................................................................5 2.3. Support Equipment List ....................................................................................................5 2.4. Test Conditions .................................................................................................................5 3. FCC ID LABEL...........................................................................................................................6 4. TEST RESULTS SUMMARY ...................................................................................................7 Modifications ................................................................................................................................7 5. TEST EQUIPMENT USED .......................................................................................................8 6. CONDUCTED POWER LINE TEST .......................................................................................9 6.1. Test Equipment .................................................................................................................9 6.2. Test Procedure ..................................................................................................................9 6.3. Test Setup..........................................................................................................................9 6.4. Configurating of the EUT .................................................................................................9 6.5. EUT Operating Condition...............................................................................................11 6.6. Conducted Power line Emission Limits..........................................................................11 6.7. Conducted Power Line Test Result.................................................................................11 7. FIELD STRENGTH IN THE 13.553-13.567 MHZ BAND ...................................................12 7.1. Test Equipment ...............................................................................................................12 7.2. Test Procedure ................................................................................................................12 7.3. Radiated Test Setup ........................................................................................................12 7.4. Configuration of the EUT ...............................................................................................12 7.5. EUT Operating Condition...............................................................................................12 7.6. Radiated Emission Limit.................................................................................................12 7.7. Radiated Emission Test Result .......................................................................................13 8. FIELD STRENGTH OF ANY EMISSIONS APPEARING OUTSIDE OF THE 13.110-14.010 MHZ BAND ..................................................................................................................14 8.1. Test Equipment ...............................................................................................................14 8.2. Test Procedure ................................................................................................................14 8.3. Radiated Test Setup ........................................................................................................14 8.4. Configuration of the EUT ...............................................................................................14 8.5. EUT Operating Condition...............................................................................................14 8.6. Radiated Emission Limit.................................................................................................14 8.7. Radiated Emission Test Result .......................................................................................15 9. FREQUENCY TOLERANCE OF THE CARRIER SIGNAL .............................................16 9.1. Test Equipment ...............................................................................................................16 9.2. Test Procedure ......................................…

Text truncated - open the document above for the full version.

SHENZHEN RDM TAG MASTER CO.,LTD. FCC ID: U7NRDM530 BT FCC ID REPORT :F07050829C Conducted Disturbance Test Radiated disturbances