U9YAL5808UWB Octal SPI Module (SBU & SAB)

www.alereon.com | 10800 Pecan Park Blvd. | Suite 100 | Austin,Tx 78750 | 512.345.4200 | 512.345.4201 4/14/2021 CONFIDENTIAL 1 of 2 ALER03 Compliance Statement for Octal AL5808: FCC ID: U9YAL5808 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator & your body. OEM INTEGRATION INSTRUCTIONS: This device is intended only for OEM integrators under the following conditions: The module must be installed in the host equipment that must be handheld, i.e., they are relatively small devices that are primarily handheld while being operated and do not employ a fixed infrastructure and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the internal on-board antenna that has been originally tested and certified with 4/14/2021 CONFIDENTIAL 2 of 2 this module. External antennas are not supported. As long as these 3 conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). The end- product may need Verification testing, Declaration of Conformity testing, a Permissive Class II Change or new Certification. Please involve a FCC certification specialist in order to determine what will be exactly applicable for the end-product. Validity of using the module certification: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. In such cases, please involve a FCC certification specialist in order to determine if a Permissive Class II Change or new Certification is required. Upgrade Firmware: The software provided for firmware upgrade will not be capable to affect any RF parameters as certified for the FCC for this module, in order to prevent compliance issues. End product labeling: This transmitter module is authorized only for use in device where the antenna may be installed such that 0 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: U9YAL5808”. Information that must be placed in the end user manual: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. This device is authorized under 47 CFR 15.519 (the FCC Rules and Regulations). The operation of this device is subject to the following restriction: This UWB device shall transmit only when it is sending information to an associated receiver. This UWB device shall cease transmission within 10 seconds unless it receives an acknowledgement from the associated receiver that its transmission is being received. An acknowledgement of reception must continue to be received by the transmitting device at least every 10 seconds of operation or the UWB device must cease transmitting

PHOTOS – EXTERNAL & INTERNAL Company: Alereon, Inc. Product Name: AL5808_Octal Report No.: ALER03 – External Internal Photos Title: ALER03 AL5808_Octal External Internal Photos To: Serial #: Issue Date: 23 March 2021 Page: 2 of 4 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1. External & Internal Photographs AL5808_Octal Back Title: ALER03 AL5808_Octal External Internal Photos To: Serial #: Issue Date: 23 March 2021 Page: 3 of 4 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com AL5808_Octal Front AL5808_Octal With Support Board 575 Boulder Court Pleasanton, California 94566, USA Tel: +1 (925) 462 0304 Fax: +1 (925) 462 0306 www.micomlabs.com

www.alereon.com | 10800 Pecan Park Blvd. | Suite 100 | Austin,Tx 78750 | 512.345.4200 | 512.345.4201 3/22/2021 CONFIDENTIAL 1 of 1 To whom it may concern, The AL5808 Octal module is too small for attaching an FCC identification label. Instead, the following statements will be added to the User’s Manual. In addition, the same statements will be printed on a sticker and adhered to the packaging for each module that is shipped. “This device contains FCC ID U9YAL5808. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) This device must accept any interference received, including interference that may cause undesired operation. “ Thanks, Parmveer Singh Director of Systems Applications Alereon, Inc. 3/22/2021

MPE/RF EXPOSURE REPORT FCC CFR 47 Part 1.1310 Report No.: ALER03-U2 Rev A MPE Company: Alereon Inc. Model Name: AL5350B Based UWB Modules MPE/RF EXPOSURE REPORT Company: Alereon Inc. Model Name: AL5350B Based UWB Modules To: FCC CFR 47 Part 1.1310 Report Serial No.: ALER03-U2 Rev A MPE This report supersedes: NONE Applicant: Alereon Inc. 10800 Pecan Park Blvd, STE 100 Austin, TX 78750 USA Issue Date: 25th March 2021 This Test Report is Issued Under the Authority of: MiCOM Labs, Inc. 575 Boulder Court Pleasanton California 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com MiCOM Labs is an ISO 17025 Accredited Testing Laboratory Title: Alereon Inc AL5350B Based UWB Modules To: FCC CFR 47 Part 1.1310 Serial #: ALER03-U2 Rev A MPE Issue Date: 25th March 2021 Page: 3 of 5 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1. MAXIMUM PERMISSABLE EXPOSURE Calculations for Maximum Permissible Exposure Levels Power Density = Pd (mW/cm 2 ) = EIRP/(4*π*d 2 ) EIRP = P * G P = Peak output power (mW) G = Antenna numeric gain (numeric) d = Separation distance (cm) Numeric Gain = 10 ^ (G (dBi)/10) Because the EUT belongs to the General Population/Uncontrolled Exposure the limit of power density is 1.0 mW/cm 2 These calculations represent worst case in terms of the exposure levels. Freq. Band (MHz) Ant Gain (dBi) Numeric Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Calculated Power Density (mW/cm 2 ) @ 20cm Power Density Limit (mW/cm 2 ) Min Calculated safe distance (cm) 3100-10600 0.00 1.00 -41.3 7.41E-05 1.5E-08 1.00 2.43E-03 Note: for mobile or fixed location transmitters the minimum separation distance is 20cm, even if calculations indicate the MPE distance to be less. Specification - Maximum Permissible Exposure Limits The Limit is defined in Table 1 of FCC §1.1310. Title: Alereon Inc AL5350B Based UWB Modules To: FCC CFR 47 Part 1.1310 Serial #: ALER03-U2 Rev A MPE Issue Date: 25th March 2021 Page: 4 of 5 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Specification - Maximum Permissible Exposure Limits TABLE 1—LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm 2 ) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposure 0.3-3.0 614 1.63 *100 6 3.0-30 1842/f 4.89/f *900/f 2 6 30-300 61.4 0.163 1.0 6 300-1,500 -- -- f/300 6 1,500-100,000 -- -- 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *100 30 1.34-30 824/f 2.19/f *180/f 2 30 30-300 27.5 0.073 0.2 30 300-1,500 -- -- f/1500 30 1,500-100,000 -- -- 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density 575 Boulder Court Pleasanton, California 94566, USA Tel: +1 (925) 462 0304 Fax: +1 (925) 462 0306 www.micomlabs.com

REGULATORY COMPLIANCE TEST REPORT FCC CFR 47 Part 15 SubPart B Report No.: ALER03-U4 Rev A Company: Alereon Inc. Model Name: AL5350B Based UWB Modules REGULATORY COMPLIANCE TEST REPORT Company Name: Alereon Inc. Model Name: AL5350B Based UWB Modules To: FCC CFR 47 Part 15 Subpart B FCC CFR 47 Part 15 Subpart B Test Report Serial No.: ALER03-U4 Rev A This report supersedes: NONE Applicant: Alereon Inc. 10800 Pecan Park Blvd, STE 100 Austin, Texas 78750 USA Issue Date: 24 rd March 2021 This Test Report is Issued Under the Authority of: MiCOM Labs, Inc. 575 Boulder Court Pleasanton California 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com MiCOM Labs is an ISO 17025 Accredited Testing Laboratory Title: Alereon Inc. AL5350B Based UWB Modules To: FCC CFR 47 Part 15 Subpart B Serial #: ALER03-U4 Rev A Issue Date: 24 th March 2021 Page: 3 of 28 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Table of Contents 1. ACCREDITATION, LISTINGS & RECOGNITION ................................................................................ 4 1.1. TESTING ACCREDITATION ........................................................................................................ 4 1.2. RECOGNITION ............................................................................................................................. 5 1.3. PRODUCT CERTIFICATION ........................................................................................................ 6 2. DOCUMENT HISTORY ......................................................................................................................... 7 3. TEST RESULT CERTIFICATE ............................................................................................................. 8 4. REFERENCES AND MEASUREMENT UNCERTAINTY ..................................................................... 9 4.1. Normative References .................................................................................................................. 9 4.2. Test and Uncertainty Procedure ................................................................................................. 10 5. PRODUCT DETAILS AND TEST CONFIGURATIONS ..................................................................... 11 5.1. Technical Details ......................................................................................................................... 11 5.2. Scope Of Test Program .............................................................................................................. 12 5.3. Equipment Model(s) and Serial Number(s) ................................................................................. 13 5.4. Antenna Details ........................................................................................................................... 13 5.5. Cabling and I/O Ports .................................................................................................................. 13 5.6. Test Configurations ..................................................................................................................... 14 5.7. Equipment Modifications ............................................................................................................. 14 5.8. Deviations from the Test Standard ............................................................................................. 14 6. TEST SUMMARY ................................................................................................................................ 15 7. TEST RESULTS .................................................................................................................................. 16 7.1. EMC EMISSIONS TEST RESULTS ........................................................................................... 16 7.1.1 Radiated Emissions ............................................................................................................ 16 Title: Alereon Inc. AL5350B Based UWB Modules To: FCC CFR 47 Part 15 Subpart B Serial #: ALER03-U4 Rev A Issue Date: 24 th March 2021 Page: 4 of 28 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1. ACCREDITATION, LISTINGS & RECOGNITION 1.1. TESTING ACCREDITATION MiCOM Labs, Inc. is an accredited Electrical testing laboratory per the international standard ISO/IEC 17025:2017. The company is accredited by the American Association for Laboratory Accreditation (A2LA) www.a2la.org test laboratory number 2381.01. MiCOM Labs test schedule is available at the following URL; http://www.a2la.org/scopepdf/2381-01.pdf Title: Alereon Inc. AL5350B Based UWB Modules To: FCC CFR 47 Part 15 Subpart B Serial #: ALER03-U4 Rev A Issue Date: 24 th March 2021 Page: 5 of 28 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1.2. RECOGNITION MiCOM Labs, Inc is widely recognized for its wireless testing and certification capabilities. In addition to being recognized for Testing and Certification under Phase 2 Mutual Recognition Agreements (MRA) with Canada, Europe, United Kingdom and Japan, our international recognition includes Conformity Assessment Body (CAB) designation status under agreements with Asia Pacific (APEC) MRA Phase 1 countri…

Text truncated - open the document above for the full version.

REGULATORY COMPLIANCE TEST REPORT FCC Part 15 Subpart F 15.519 Hand-Held UWB Device Report No.: ALER03-U2 Rev C Company: Alereon Inc. Model Name: AL5350B Based UWB Modules REGULATORY COMPLIANCE TEST REPORT Company Name: Alereon Inc. Model Name: AL5350B Based UWB Modules To: FCC CFR 47 Part 15 Subpart F 15.519 Test Report Serial No.: ALER03-U2 Rev C This report supersedes: NONE Applicant: Alereon Inc. 10800 Pecan Park Blvd, STE 100 Austin, Texas 78750 USA Issue Date: 20 th April 2021 This Test Report is Issued Under the Authority of: MiCOM Labs, Inc. 575 Boulder Court Pleasanton California 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com MiCOM Labs is an ISO 17025 Accredited Testing Laboratory Title: Alereon Inc. AL5350B Based UWB Modules To: FCC CFR 47 Part 15 Subpart F 15.519 Serial #: ALER03-U2 Rev C Issue Date: 20 th April 2021 Page: 3 of 172 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com Table of Contents 1. ACCREDITATION, LISTINGS & RECOGNITION ................................................................................ 4 1.1. TESTING ACCREDITATION ........................................................................................................ 4 1.2. RECOGNITION ............................................................................................................................. 5 1.3. PRODUCT CERTIFICATION ........................................................................................................ 6 2. DOCUMENT HISTORY ......................................................................................................................... 7 3. TEST RESULT CERTIFICATE ............................................................................................................. 8 4. REFERENCES AND MEASUREMENT UNCERTAINTY ..................................................................... 9 4.1. Normative References .................................................................................................................. 9 4.2. Test and Uncertainty Procedure ................................................................................................. 10 5. PRODUCT DETAILS AND TEST CONFIGURATIONS ..................................................................... 11 5.1. Technical Details ......................................................................................................................... 11 5.2. Scope Of Test Program .............................................................................................................. 12 5.3. Equipment Model(s) and Serial Number(s) ................................................................................. 13 5.4. Antenna Details ........................................................................................................................... 13 5.5. Cabling and I/O Ports .................................................................................................................. 13 5.6. Test Configurations ..................................................................................................................... 14 5.7. Equipment Modifications ............................................................................................................. 14 5.8. Deviations from the Test Standard ............................................................................................. 14 6. TEST SUMMARY ................................................................................................................................ 15 7. TEST EQUIPMENT CONFIGURATION(S) ......................................................................................... 16 7.1. Conducted Test Setup ................................................................................................................ 16 7.2. Radiated Emissions - 3m Chamber ............................................................................................ 18 8. MEASUREMENT AND PRESENTATION OF TEST DATA ............................................................... 21 9. TEST RESULTS .................................................................................................................................. 22 9.1. UWB Bandwidth .......................................................................................................................... 22 9.2. Average Transmit Power ............................................................................................................. 32 9.3. Peak Power Density .................................................................................................................... 36 9.4. Transmitter Spurious Band Emissions ........................................................................................ 46 9.4.1. Transmitter Spurious Emissions ........................................................................................... 48 9.4.2. Band 1 .................................................................................................................................. 48 9.4.3. Band 2 .................................................................................................................................. 51 9.4.4. Band 3 & 6 ............................................................................................................................ 53 9.4.5. Band 6 .................................................................................................................................. 54 9.4.6. GPS Band Emissions ........................................................................................................... 56 9.4.6.0.1. 3432 MHz ..............................................................…

Text truncated - open the document above for the full version.

PHOTOS - TEST SETUP Company: Alereon, Inc. Product Name: AL5808_Octal Report No.: ALER03 – Test Setup Photos Title: ALER03 AL5804_Impact Test Setup Photos To: Serial #: Issue Date: 24 March 2021 Page: 2 of 6 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1. Test Setup Photographs 1.1.1. Test Setup - RE#1 - Radiated Emissions - 3m Chamber AL5808_Octal Digital Emissions 30-1000MHz Title: ALER03 AL5804_Impact Test Setup Photos To: Serial #: Issue Date: 24 March 2021 Page: 3 of 6 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com TX Spurious 1-18GHz **AL5834_Combat256 was tested for TX spurious emissions 1-18GHz and data used for all 6 units as statement from client declared all 6 boards used the same Alereon radio chipset. Title: ALER03 AL5808_Octal Test Setup Photos To: Serial #: Issue Date: 24 March 2021 Page: 4 of 6 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com AL5808_Octal Digital Emission 30-1000MHz Closeup Title: ALER03 AL5808_Octal Test Setup Photos To: Serial #: Issue Date: 24 March 2021 Page: 5 of 6 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1.1.2. Test Setup - RF#1 - Conducted RF Conducted **AL5834_Combat256 was tested for RF conducted and data used for all 6 units as statement from client declared all 6 boards uses the same Alereon radio chipset. 575 Boulder Court Pleasanton, California 94566, USA Tel: +1 (925) 462 0304 Fax: +1 (925) 462 0306 www.micomlabs.com