UGP-4049270BTX Smart Link Pro

SmartLink Pro Instruction Description SmartLink pro is a Hot-swappable dongle. The curtains or roller blinds can be opened, closed, and positioned via the Bond app after connecting the dongle to curtain or roller blind motor Configuration Requirements A Bond Bridge pro with Internet connectivity and a phone with the Bond app installed. Pair dongle to Bond Bridge Pro 1. Open the Bond app and tap the plus sign in the upper right corner. 2. Select "Shades, Roofs, Screens & Awnings" 3. Select "BTX Shade" 4. Click "Start" 5. Change the device name and select the room to install, 6. Press and hold the button on the dongle for 3-5 seconds, the LED will solid blue and the motor will jog. 7. Click "pair" in the app. 8. Set the limits according to the prompts. Control the motor The motor can be operated by turning it on/off or by dragging the position bar in bond app. FCC Notice This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the device and receiver. --Connect the device into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment RF warning for portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

12/9 Fed Auth 7435 Colu USA AT T FCC BTX soug purs BT X appl entit BT X soug Kas inte g anti- Guid Sig n Prin Titl e Com Date Co 9/2025 eral Comm u horization a 5 Oakland M umbia, MD 2 A TN.: Review C ID: UGP-4 X Holdings I ght is not “c suant to sec Note: If any of t h include X Holdings I lication, the ty or any of X Holdings I ght does no persky Lab, grated Kas -virus softwa dance sectio ned: ted name: B e: GM mpany Name e: 12/9/2025 overed Eq unications C nd Evaluatio Mills Road 21046 wing Engin 4049270 nc (“the ap p covered” equ ction 2.903 o the equipm he entities id an explanat nc (“the app applicant is its subsidia nc (“the app ot include cy , Inc. or any persky Lab are pursuan on B(2a). Ben Wooda e: BTX Hold 5 BT quipment Commission on Division neer plicant”) cer uipment pro of the FCC ent for whi c dentified on tion on why plicant”) cer s not identif aries or affili plicant”) cer ybersecurity y of its succe , Inc. (or an nt to DA-24- all dings Inc TX Holding t Certifica n rtifies that th ohibited from rules. ch the applic n the current y the equipm rtifies that, a fied on the C ates) as an rtifies that th y or anti-viru essors and y of its suc c -886 and KD s Inc ation Attes he equipmen m receiving cant seeks a t Covered L ment is not “ as of the dat Covered Lis entity prod he equipmen us software assignees, cessors and DB 986446 station Le nt for which an equipm e authorizatio List, the app covered” eq te of the filin st (as a spec ucing “cove nt for which produced o including e d assignees D01 Covere etter authorizatio ent authoriz on is produc plicant shoul quipment. ng of the cifically nam ered” equipm h authorizat or provided quipment w s) cybersecu ed Equipme on is zation ced by ld med ment. tion is by with urity or ent

December 09 2025 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: UGP-4049270 Product Name: BTX Smart Link Pro Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential: • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature>： Name：Ben Woodall Title：GM Applicant Company：BTX Holdings Inc

Dece Fede Auth 7345 Colu On o C, 1s Villa to ac that certi f defin labe For i beha for c Dal <Sig n Name Title： Applic ember 09 2 eral Commu horization & 5 Oakland M umbia, Mary our behalf, I st Floor, Blo ge, Nansha ct as our age submitted d fication is so ned in the Fe l identical to instances w alf, I acknow certification, las, Tx 7 nature>： e：Ben Woo GM cant Compa 2025 unications C Evaluation D Mills Road land 21046 appoint She ock B, Jun X n District, S ent in the pr documents p ought. I also ederal Comm o that submit where our au wledge that still resides 5238, U S odall any：BTX H ommission Division Author i enzhen Time Xiang Da Bui henzhen, C reparation of properly desc o certify that munications tted for appr uthorized ag all responsi with B T X SA Holdings Inc ity to Act as eway Testin ilding, Zhon hina (Name f this applica cribe the de each unit m s Commissio roval with th ent signs th ibility for com X Holding c s Agent ng Laborator gshan Park of Agent co ation for equ evice or syst manufactured on’s regulatio his applicatio he applicatio mplying with s Inc / 10 ries/ Zone C Road West ompany nam uipment cert em for which d, imported ons will hav on. on for certific h the terms 763 San d C, 1st Floor, t, Tong Le me and addr tification. I c h equipme n or marketed ve affixed to cation on ou and conditio den Drive Zone ress) ertify t d, as it a ur ons e,

Acc ERP 2.8 (Wo The ording to =Peak Powe mW rst case n SAR ev a o 447498 D er + Anten recorded) aluation i RF Expo For FCC D04 Interi nna Gain - s not re q osure eval C ID: UGP- im General -2.15=-1.6 quired luation -4049270 l RF Expos 69-0.61-2. sure Guida .15=-4.45d ance v01 dBm=0.359m mW <

Report No.: TW2510039-02E Applicant: BTX Holdings Inc Product: BTX Smart Link Pro Model No.: 404.9270, SmartLink Pro Trademark: N/A Test Standards: FCC Part 15.247 Test Result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.10, FCC Part 15.247 for the evaluation of electromagnetic compatibility Approved By Terry Tang Manager Dated: October 30, 2025 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TESTING LABORATORIES Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China Tel (755) 83448688, Fax (755) 83442996, E-Mail:[email protected] Report No.: TW2510039-02E Page 2 of 59 Date: 2025-10-30 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： FCC-Registration No.: 744189 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 744189. Industry Canada (IC) —Registration No.:5205A The EMC Laboratory has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 5205A. A2LA (Certification Number:5013.01) The EMC Laboratory has been accredited by the American Association for Laboratory Accreditation (A2LA). Certification Number:5013.01 CAB identifier: CN0033 Report No.: TW2510039-02E Page 3 of 59 Date: 2025-10-30 The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the SHENZHEN TIMEWAY TESTING LABORATORIES. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the SHENZHEN TIMEWAY TESTING LABORATORIES. to his customer. Supplier or others persons directly concerned. SHENZHEN TIMEWAY TESTING LABORATORIES. will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The SHENZHEN TIMEWAY TESTING LABORATORIES. reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT ........................................................................................... 4 1.4 Submitted Sample.............................................................................................. 4 1.5 Test Duration................................................................................................... 5 1.6 Test Uncertainty............................................................................................... 5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 6 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test...................................................................... 8 5.1 Schematics of the Test........................................................................................ 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................................................................... 8 5.4 EUT Operating Condition.................................................................................... 9 5.5 Conducted Emission Limit................................................................................... 9 5.6 Test Result...................................................................................................... 9 6.0 Radiated Emission test...................................................................................... 12 6.1 Test Method and Test Procedure............................................................................ 12 6.2 Configuration of the EUT.........................................…

Text truncated - open the document above for the full version.

ANTENNA SPECIFICATION Specifications Summary ITEM SPEC. Model Name Center Frequency Horizontal Vertical 2400MHz 2450MHz2500MHz2400MHz2450MHz 2500MHz -1.66 -0.84 -0.61 -6.16 -3.65 -2.21 MAX. Gain -0.61 Polarization Horizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance 50 Ohm Antenna Length 33.1849mm Manufacture Dongguan Couson Antenna Photo & Length (mm) Horizontal: 2400 MHz 2450 MHz 2500 MHz Max: 0 Min: -40 Scale: 5/div Frequency (MHz) Gain(dBi) Max. Min. Avg. 2400 -1.66179 -30.2813 -8.78713 2450 -0.84781 -38.7595 -7.87812 2500 -0.6156 -23.6329 -6.99139 Vertical: 2400 MHz 2450 MHz 2500 MHz Max: 0 Min: -30 Scale: 5/div Frequency (MHz) Gain(dBi) Max. Min. Avg. 2400 -6.1623 -23.1425 -12.5295 2450 -3.6534 -26.2866 -10.6699 2500 -2.21101 -29.4381 -9.58526

Conducted Emission Test Setup: Radiated Emission Test Setup: