UJYMS0200Wireless radio controller to trigger cameras and/or strobes.

Tamrac, Inc. FCC ID: UJYMS0200 Report Number: R1007294-231 Page 23 of 24 FCC Part15.231 Report 10 EXHIBIT C - EUT PHOTOGRAPHS 10.1 EUT – Front View 10.2 EUT - Back View

Tamrac, Inc. FCC ID: UJYMS0200 Report Number: R1007294-231 Page 19 of 24 FCC Part15.231 Report 8 EXHIBIT A – FCC EQUIPMENT LABELING REQUIREMENTS 8.1 FCC Labeling Requirements As per FCC §2.925 Identification of equipment (a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following: (1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification. Example: FCC ID XXX123 Where: XXX—Grantee Code, 123—Equipment Product Code As per FCC §15.19 Labeling Requirements (a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be labeled as follows: (3) All other devices shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (4) Where a device is constructed in two or more sections connected by wires and marketed together, the statement specified above is required to be affixed only to the main control unit. If the EUT is integrated within another device then a label affixed to the host shall also state, “Contains FCC ID: XXXXXX” (5) When the device is so small or for such use that it is not practicable to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device. 8.2 FCC ID Label Contents Tamrac, Inc. FCC ID: UJYMS0200 Report Number: R1007294-231 Page 20 of 24 FCC Part15.231 Report 8.3 FCC ID Label Location Label here

Tamrac, Inc. FCC ID: UJYMS0200 Report Number: R1007294-231 Page 24 of 24 FCC Part15.231 Report 10.3 EUT PCB Assembly – Top View 10.4 EUT PCB Assembly - Bottom View ***** END OF REPORT*****

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*” (Rev.2) FCC PART 15, SUBPART C TEST AND MEASUREMENT REPORT For Tamrac, Inc. 9240 Jordan Avenue, Chatsworth, CA 91311, USA FCC ID: UJYMS0200 Report Type: Original Report Product Type: Wireless Radio Controller Test Engineer: Kevin Li Report Number: R1007294-231 Report Date: 2010-09-07 Reviewed By: Victor Zhang Test Engineer, RF Lead Prepared By: (84) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Avenue, Sunnyvale, CA 94089, U.S.A. Tel: (408) 732-9162 Fax: (408) 732-9164 Tamrac, Inc. FCC ID: UJYMS0200 Report Number: R1007294-231 Page 2 of 24 FCC Part15.231 Report TABLE OF CONTENTS 1 GENERAL INFORMATION .............................................................................................................................. 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ........................................................................ 4 1.2 MECHANICAL DESCRIPTION............................................................................................................................ 5 1.3 OBJECTIVE...................................................................................................................................................... 5 1.4 RELATED SUBMITTAL(S)/GRANT(S) ................................................................................................................ 5 1.5 TEST METHODOLOGY...................................................................................................................................... 5 1.6 MEASUREMENT UNCERTAINTY....................................................................................................................... 5 1.7 TEST FACILITY................................................................................................................................................ 5 2 SYSTEM TEST CONFIGURATION ................................................................................................................. 7 2.1 JUSTIFICATION................................................................................................................................................. 7 2.2 EUT EXERCISE SOFTWARE............................................................................................................................. 7 2.3 EQUIPMENT MODIFICATIONS........................................................................................................................... 7 2.4 SPECIAL ACCESSORIES.................................................................................................................................... 7 2.5 LOCAL SUPPORT EQUIPMENT.......................................................................................................................... 7 2.6 POWER SUPPLY AND LINE FILTERS................................................................................................................. 7 2.7 INTERFACE PORTS AND CABLING.................................................................................................................... 7 2.8 EUT CONFIGURATION DETAILS...................................................................................................................... 7 3 SUMMARY OF TEST RESULTS...................................................................................................................... 8 4 FCC §15.203 – ANTENNA REQUIREMENT ................................................................................................... 9 4.1 APPLICABLE STANDARD.................................................................................................................................. 9 4.2 TEST RESULT................................................................................................................................................... 9 5 FCC §15.231(A)(1)– DEACTIVATION TIME................................................................................................ 10 5.1 APPLICABLE STANDARD................................................................................................................................10 5.2 TEST SETUP DIAGRAM.................................................................................................................................. 10 5.3 TEST EQUIPMENT LIST AND DETAILS............................................................................................................ 10 5.4 TEST ENVIRONMENTAL CONDITIONS............................................................................................................ 10 5.5 TEST RESULT................................................................................................................................................. 11 6 FCC §15.231(B) – FIELD STRENGTH OF EMISSIONS .............................................................................. 12 6.1 APPLICABLE STANDARD................................................................................................................................12 6.2 TEST SETUP................................................................................................................................................... 13 6.3 TEST PROCEDURE.......................................................................................................................................... 13 6.4 CORRECTED AMPLITUDE & MARGIN CALCULATION..................................................................................... 13 6.5 TEST EQUIPMENT LIST AND DETAILS.....................................…

Text truncated - open the document above for the full version.

Tamrac, Inc. FCC ID: UJYMS0200 Report Number: R1007294-231 Page 21 of 24 FCC Part15.231 Report 9 EXHIBIT B - TEST SETUP PHOTOGRAPHS 9.1 Radiated Emissions - Front View 9.2 Radiated Emissions - Rear View (Below 1 GHz) Tamrac, Inc. FCC ID: UJYMS0200 Report Number: R1007294-231 Page 22 of 24 FCC Part15.231 Report 9.3 Radiated Emissions - Rear View (Above 1 GHz)