UNYEWPP202Wireless push-button

FCC Regulations This device complies with Part 15 of the FCC Rules. This device should be used in accordance with the instructions. Any changes or modifications are not allowed.

EWPT-202BLOCKDIAGRAM.(TRANSMITTER&SENSOR) EWPR-202BLOCKDIAGRAM.(RECEIVER) EWPR-202BLOCKDIAGRAM.OFRFDECODERCIRCUIT EWPP-202BLOCKDIAGRAM.(BUTTONTRANSMITTER)

EXHIBIT C - EUT PHOTOGRAPHS EUT – Front side view EUT – Top side view EUT – Rear side view

EXHIBIT A – FCC PRODUCT LABELING AND WARNING STATEMENT FCC ID Label The FCC labels should contain FCC statement in FCC 15.19 paragraph (3). A sample of the statement is presented hereinafter as reference. Also, as per FCC §15.19 a(4) Where a device is constructed in two or more sections connected by wires and marketed together, the statement specified above is required to be affixed only to the main control unit. If the EUT is integrated within another device then a label affixed to the host shall also state, “Contains FCC ID: XXXXXXXXXX” Proposed Label Location on EUT Rear View of EUT / Proposed FCC ID Location As per FCC §15.19 (b) (4), the label shall not be a stick-on, paper label. The label on these products shall be permanently affixed to the product and shall be readily visible to the purchaser at the time of purchase, as described in Section 2.925(d) of this chapter. "Permanently affixed" means that the label is etched, engraved, stamped, silk-screened, indelibly printed, or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal, plastic, or other material fastened to the equipment by welding, riveting, or a permanent adhesive. The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: UNYEWPP202 2.1875" 1.0"

Component side view Solder side view Integral Antenna view

The EWP-202C annunciator system is designed with dual counter active-infrared technology. The invisible dual infrared beam triggers a chime sound and registers a count on the digital counter when the infrared beam is interrupted. The transmitting signal differentiates among the Entries and Exits therefore making it a more efficient device. The system counts the number of people that enter the facility and sounds a chime upon entering and single sound upon exiting. Each event is counted, recorded and registered by the built-in digital counter and can be viewed and compared later in Entry/Exit modes. The annunciator is also equipped with an Alert Mode which sounds the built-in siren when triggered adding additional security.

Note: This test report is for the customer shown above and their specific product only. It may not be duplicated without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. FCC PART 15.231 EMI MEASUREMENT AND TEST REPORT For K&J Electronics #103-603, Buchun Techno-Park, Buchin-city, Kyunggi-do, Korea 421-809 FCC ID: UNYEWPP202 Model: EWPP-202 This Report Concerns: Original Report Product Type: Wireless Push Button Test Engineer: Oscar Au Report No.: R0609217 Report Date: 2006-09-25 Reviewed By: Test Engineer: James Ma Prepared By: (tz) Bay Area Compliance Laboratory Corp. 1274 Anvilwood Ave. Sunnyvale, CA 94089, U.S.A. Tel: (408) 732-9162 Fax: (408) 732-9164 K&J Electronics FCC ID: UNYEWPP202 Report # R0609217 Page 2 of 19 FCC Part 15.231 Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................................................3 EUT PHOTO.................................................................................................................................................................3 OBJECTIVE...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................3 TEST METHODOLOGY..................................................................................................................................................3 MEASUREMENT UNCERTAINTY....................................................................................................................................4 TEST FACILITY.............................................................................................................................................................4 SYSTEM TEST CONFIGURATION ..........................................................................................................................5 JUSTIFICATION.............................................................................................................................................................5 EUT EXERCISE SOFTWARE..........................................................................................................................................5 SPECIAL ACCESSORIES.................................................................................................................................................5 SCHEMATICS / BLOCK DIAGRAM..................................................................................................................................5 EQUIPMENT MODIFICATIONS.......................................................................................................................................5 TEST SETUP BLOCK DIAGRAM.....................................................................................................................................6 SUMMARY OF TEST RESULTS ...............................................................................................................................7 §15.203 - ANTENNA REQUIREMENT......................................................................................................................8 APPLICABLE STANDARD..............................................................................................................................................8 ANTENNA CONNECTED CONSTRUCTION......................................................................................................................8 §15.207 – CONDUCTED EMISSIONS .......................................................................................................................9 APPLICABLE STANDARD..............................................................................................................................................9 §15.205, §15.209, & §15.231(A1-A5) – RESTRICTED BAND AND RADIATED EMISSION DATA................10 APPLICABLE STANDARD: FCC §15.205 RESTRICTED BANDS OF OPERATION.............................................................10 APPLICABLE STANDARD: FCC §15.209 RADIATED EMISSION LIMITS, GENERAL REQUIREMENTS...............................10 APPLICABLE STANDARD: FCC §15.231 PERIODIC OPERATION IN THE BAND 40.66 - 40.70 MHZ AND ABOVE 70 MHZ.11 §15.231(A) – PERIODIC OPERATION IN THE BAND 40.66 – 40.70 MHZ AND ABOVE 70 MHZ ...............12 APPLICABLE STANDARD REQUIREMENT....................................................................................................................12 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................12 TEST SETUP DIAGRAM...............................................................................................................................................12 TEST RESULT.............................................................................................................................................................12 §15.231(B) – FIELD STRENGTH OF EMISSIONS ................................................................................................14 APPLICABLE STANDARD REQUIREMENT....................................................................................................................14 RADIATED EMISSIONS EUT SETUP............................................................................................................................14 SPECTRUM ANALYZER SETUP............................................................................…

Text truncated - open the document above for the full version.

EXHIBIT B - RADIATED SETUP PHOTOGRAPHS Radiated Emissions - Front View Radiated Emissions – Rear View