UPO2765Zinwave 2765 Distributed Antenna System

Zinwave2700DAS–UserManual Issue1.2
April2007
©ZinwaveLtd.2007 











 Zinwave2700 DistributedAntennaSystem  UserManual 



Zinwave2700DAS–UserManual Issue1.2
April2007
©ZinwaveLtd.2007  DocumentHistory
IssueDateChangestopreviousissue 1.2
03.04.2007
•
Added
information
regarding
RF
exposure
1.1
27.03.2007
•
Editorial
changes
•
Changed
default
IP,
added
description
of
DHCP
1.0
05.03.2007
•
Initial
release


Zinwave2700DAS–UserManual Issue1.2
April2007
©ZinwaveLtd.2007  NOTICES
©
Zinwave
Ltd.
2007
No
part
of
this
manual
may
be
reproduced
in
any
form
or
by
any
means
(including
electronic
storage
and
retrieval
or
translation
into
a
foreign
language)
without
prior
agreement
and
written
consent
from
Zinwave
Ltd.
as
governed
by
United
Kingdom
and
international
copyright
laws.

Edition Issue
1.2,
April
2007

Warranty The
material
contained
in
this
document
is
provided
“as
is,”
and
is
subject
to
being
changed,
without
notice,
in
future
editions.
Further,
to
the
maximum
extent
permitted
by
applicable
law,
Zinwave
disclaims
all
warranties,
either
express
or
implied,
with
regard
to
this
manual
and
any
information
contained
herein,
including
but
not
limited
to
the
implied
warranties
of
merchantability
and
fitness
for
a
particular
purpose.
Zinwave
shall
not
be
liable
for
errors
or
for
incidental
or
consequential
damages
in
connection
with
the
furnishing,
use,
or
performance
of
this
document
or
of
any
information
contained
herein.
Should
Zinwave
and
the
user
have
a
separate
written
agreement
with
warranty
terms
covering
the
material
in
this
document
that
conflict
with
these
terms,
the
warranty
terms
in
the
separate
agreement
shall
control.

TechnologyLicenses The
hardware
and/or
software
described
in
this
document
are
furnished
under
a
license
and
may
be
used
or
copied
only
in
accordance
with
the
terms
of
such
license.

SafetyNotices CAUTION A
CAUTION
notice
denotes
a
hazard.
It
calls
attention
to
an
operating
procedure,
practice,
or
the
like
that,
if
not
correctly
performed
or
adhered
to,
could
result
in
damage
to
the
product
or
loss
of
important
data.
Do
not
proceed
beyond
a
CAUTION
notice
until
the
indicated
conditions
are
fully
understood
and
met.

WARNING A
WARNING
notice
denotes
a
hazard.
It
calls
attention
to
an
operating
procedure,
practice,
or
the
like
that,
if
not
correctly
performed
or
adhered
to,
could
result
in
personal
injury
or
death.
Do
not
proceed
beyond
a
WARNING
notice
until
the
indicated
conditions
are
fully
understood
and
met.

Zinwave2700DAS–UserManual Issue1.2
April2007
©ZinwaveLtd.2007  TrademarkAcknowledgements Cisco
®
and
Aironet
®
are
registered
trademarks
of
Cisco
Corporation.
Pentium
®
is
a
registered
trademark
of
Intel
Corporation.
Adobe
®
is
a
trademark
of
Adobe
Systems
Incorporated.
Windows
XP,
Windows
2000,
and
Windows
98
are
U.S.
registered
trademarks
of
Microsoft
Corporation.
All
other
trademarks
are
the
property
of
their
respective
holders.

Aboutthisguide This
guide
contains
installation
and
operating
instructions
for
the
Zinwave
2700
Distributed
Antenna
System
(DAS).
The
basic
2700
DAS
consists
of
one
Hub
Unit
(HU)
and
up
to
8
Antenna
Units
(AU).
This
guide
is
one
member
of
a
comprehensive
documentation
set
for
the
Zinwave
DAS.
It
is
designed
to
provide
you
with
a
smooth,
successful
installation
and
setCup.
In
addition
to
this
guide,
the
documentation
set
includes:

o
Installation
Guide
o
System
Design
and
Configuration
(To
be
added
later)
o
Software
Manual

Zinwave2700DAS–UserManual Issue1.2
April2007
©ZinwaveLtd.2007  TABLEOFCONTENTS
Document
History
2 Edition
3 Warranty
3 Technology
Licenses
3 Safety
Notices
3 Trademark
Acknowledgements
4 About
this
guide
4 Chapter
1 System
Description8 1.1 Overview
8 1.2 Key
features
8 1.3 Architecture
9 1.4 System
Components
11 1.5 Configuration
and
Control
12 Chapter
2 Quick
Start13 2.1 Overview
13 2.2 Setting
up
the
Hub
Unit
13 2.3 Setting
up
the
Antenna
Units
14 2.4 Configuring
the
system
15 Chapter
3 Equipment
Description17 3.1 2700
Hub
Unit
17 3.2 2780/2781
SFP
module
24 3.3 2760
+
2765
Antenna
Unit
–
Wideband
27 3.4 277X
Antenna
Unit
–
Band
specific
36 Chapter
4 Configuration
and
Control42 4.1 Overview
42 4.2 Control
via
ZinConfig
42 4.3 Control
via
Command
Line
Interface
(CLI)
46 Chapter
5 Get
Assistance,
if
You
Need
It54 5.1 Troubleshooting
the
2700
DAS
54 5.2 Device
communication
problems
55 5.3 Returning
the
System
for
Service
55 5.4 Warranty
repair
55 5.5 Preparing
the
system
for
shipping
55 Appendix
A Safety
and
Regulatory
Information56 A.1 Warning
and
caution
notices
56 A.2 General
safety
considerations
58 A.3 Optical
Safety
Precautions
58 A.4 Installation,
Use
and
Storage
58 A.5 Signal
and
input
power
59 Appendix
B System
Information60 Zinwave2700DAS–UserManual Issue1.2
April2007
©ZinwaveLtd.2007  B.1 Overview
60 B.2 ZinConfig/CLI
Hardware
and
Software
Requirements
60 B.3 System
specification
61 Appendix
C Glossary
of
terms67 C.1 Abbreviations
67

Zinwave2700DAS–UserManual Issue1.2
April2007
©ZinwaveLtd.2007  TABLEOFFIGURES
Figure
1C1: Extended
MMF
bandwidth
using
the
Zinwave
patented
technology.....8 Figure
1C2: Schematic
of
a
basic
8Cport
2700
system. ............................................9 Figure
1C3: Five
different
possibilities
to
distribute
the
input
signals. ....................10 Figure
3C1: Block
diagram
of
the
2700
HU. ...........................................................17 Figure
3C2: Front
View
of
the
2700
Hub
Unit. ........................................................18 Figure
3C3: Re…

Text truncated - open the document above for the full version.

Registered in England No. 4587255 ZinWave Ltd Harston Mill Harston Cambridge CB2 5GG 22 nd March, 2007 Telecommunication Certification Body RFI Global Services Ltd. Pavilion A Ashwood Park Basingstoke Hampshire RG23 8BG United Kingdom To whom it may concern This is to certify that ZinWave Limited authorises RFI Global Services Limited to act on our behalf for the application of the 2765 to RFI Global Services Ltd. Telecommunication Certification Body. We certify that we are not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. Yours sincerely

Date 28 th March 2006 Telecommunication Certification Body RFI Global Services Ltd. Pavilion A Ashwood Park Basingstoke Hampshire RG23 8BG United Kingdom Subject: Certification Application FCC ID: UPO2765 It is requested that the following information is to be held short term confidential on behalf of Zinwave Ltd until such time that the product is in general release. FCC Rules Part 0.459 refers. User manual ZinWave 2700 DAS User Manuall(Issue 1.1 ).pdf 68 Pages Datasheet 2700_2765DataSheet 1.1.pdf 4 Pages Operational Zinwave DAS2700_OperationalDescription.pdf 4 Pages Description Labelling 2700Hub_labelLocation.pdf 1 page ZP301208-X3.PDF 1 page ZP301209-X3 Rear label.PDF 1 page ZP301210-X2.PDF 1 Pages ZP303012-X1 2765 (LabelLocation).pdf 1 Pages ZP303012-X1 2765 (Label).pdf 1 Pages Photos ExternalPhotos1.pdf 8 Pages ExternalPhotos2.pdf 6 Pages Zinwave Ltd is a VC funded start up company. The 2700, 2765 distributed antenna products reflect the companies first product offering. The 2700, 2765 product embodies the company intellectual property which is confidential to Zinwave. Patents are pending in both the US and Europe relating to this IP. The IP and product design details contained in these files are a differentiator between Zinwave Ltd and other commercially available products. It is essential that this remains confidential. It is requested that this information remains short term confidential as it is commercially sensitive and also IP sensitive. Release of this technical information, ahead of a general product release, would be commercially damaging to Zinwave, impacting both the company valuation and viability. Any such information released to date has been under a specific confidential disclosure agreement between a third party and Zinwave Ltd. In addition it is requested that the following sub-set of the documentation remains always confidential. Block diagram Block diagrams(2765).pdf 4 Pages SFP_diagram.pdf 1 Page Bill of material Zinwave HUB Unit ZP00100 BOM v2.01 .pdf 18 Pages Zinwave SFP 6.2_bom.pdf 4 Pages ZP500004-7.00(Hub SFP Mechanical BOM).pdf 1 Page ZP200020-1.07(2765AntennaUnit_motherboard).pdf 4 Pages ZP200021-1.0(2765AntennaUnit_opticDBoard).pdf 1 Page ZP500005-1.01(2765AntennaUnit_box_build).pdf 1 Page Circuit schematics SFP_SCHEMATIC_6.1.pdf 3 Pages Ziniwave_rev1.2_AU_MB_scematic(2765).pdf 5 Pages Zinwave_ZP000104_1.1_AU_DB_scematic(2765).pdf 5 Pages Zinwave Hub Schematic V2.11.pdf 16 Pages Photos InternalPhotos.pdf 3 Pages It is requested that the information listed above remains always confidential as it is commercially sensitive and also IP sensitive. This level of detail would not be generally available even following product release and remains Zinwave Confidential. Release of this technical information would be commercially damaging to Zinwave, impacting both the company valuation and viability. In addition to above request, it is also required to have permanent confidentiality for internal photographs. The reason for this request is that, unit is permanently mounted and not publicly accessible. Yours sincerely

0.00 61.0 30.0 9.0 5.0 7.0 10.5 38.8 0.0023.0 ZINWAVE LOGO ARTWORK SUPPLIED FONT COLOUR: PANTONE 541 WHEELIE BIN LOGO (RECYCLING) X2 50.0 BACKGROUND COLOUR: TO BE SOLID WHITE.1. FONT COLOUR: PANTONE 541.2. FONT SIZE: SEE DRAWING.3. NOTES: REVISIONS ZONE REV.DESCRIPTIONDATEAPPROVED X1INITIAL RELEASE28/09/2006K LEESON X2REMOVED FCC NUMBER1.01/11/2006K LEESON D E F C 1234 B A 3215 C D 4678 A B REVISION: X2 HUB / LABEL, BOTTOM ZP301210-X2 0.90 A3 SHEET 1 OF 1 SCALE: 2:1 DWG NO. TITLE: DO NOT SCALE DRAWING MATERIAL: DATE WEIGHT: FINISH: UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS THIRD ANGLE PROJECTION MANUFACTURING APRV'D BY: ENGINEERING APRV'D BY: CHECKED BY: DESIGNER / ENGINEER: SIZE TOLERANCES UNLESS OTHERWISE SPECIFIED X.X 0.20 X.XX 0.10 X.XXX 0.05 ANGLES: 0.5 HARSTON MILL HARSTON, CAMBRIDGE CB2 5GG FILE LOCATION K LEESON K LEESON K LEESON 01 NOV 06 D E F C 1234 B A 3215 C D 4678 A B ZP301210-X2 0.90 A3 SHEET 1 OF 1 SCALE: DWG NO. TITLE: DO NOT SCALE DRAWING MATERIAL: DATE WEIGHT: FINISH: UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS THIRD ANGLE PROJECTION MANUFACTURING APRV'D BY: ENGINEERING APRV'D BY: CHECKED BY: DESIGNER / ENGINEER: SIZE TOLERANCES UNLESS OTHERWISE SPECIFIED X.X 0.20 X.XX 0.10 X.XXX 0.05 ANGLES: 0.5 HARSTON MILL HARSTON, CAMBRIDGE CB2 5GG FILE LOCATION K LEESON K LEESON K LEESON 28 SEP 06 28 SEP 06

MATERIAL: WEIGHT: FINISH: THIRD ANGLE PROJECTION DIMENSIONS ARE IN MILLIMETERS UNLESS OTHERWISE SPECIFIED: 0.5 ANGLES: TOLERANCES UNLESS OTHERWISE SPECIFIED X.X 0.20 X.XX 0.10 X.XXX 0.05 DETAIL B SCALE 3 : 1

MATERIAL: WEIGHT: FINISH: THIRD ANGLE PROJECTION DIMENSIONS ARE IN MILLIMETERS UNLESS OTHERWISE SPECIFIED: ANGLES: 0.5 TOLERANCES UNLESS OTHERWISE SPECIFIED X.X 0.20 X.XX 0.10 X.XXX 0.05 B

Zinwave 2700 DAS – Operational description Issue 1.0 April 11, 2007 ZINWAVE 2700 DAS - INSTALLATION AND TECHNICAL MANUAL Page i ZINWAVE 2700 DISTRIBUTED ANTENNA SYSTEM Operational Description Zinwave 2700 DAS – Operational description Issue 1.0 April 11, 2007 ZINWAVE 2700 DAS - INSTALLATION AND TECHNICAL MANUAL Page ii Zinwave 2700 DAS – Operational description Issue 1.0 April 11, 2007 ZINWAVE 2700 DAS - INSTALLATION AND TECHNICAL MANUAL Page iii CONTENTS Table of Contents Contents ............................................................................................................................................................................. iii 1 Overview of the ZinWave 2700 DAS ............................................................................................................................1 1.1 Introduction ...........................................................................................................................................................1 1.2 The components....................................................................................................................................................2 1.3 The technology......................................................................................................................................................2 1.4 The system............................................................................................................................................................2 1.5 Integrated Management Software .........................................................................................................................2 2 Equipment Description .................................................................................................................................................4 2.1 2700 Hub Unit .......................................................................................................................................................4 2.1.1 Overview ........................................................................................................................................................4 2.1.2 Dimensions and Weight .................................................................................................................................4 2.1.3 Connection panels and LED indicators ..........................................................................................................5 2.1.4 Environmental ................................................................................................................................................7 2.2 2780/2781 SFP module.........................................................................................................................................8 2.2.1 Overview ........................................................................................................................................................8 2.2.2 Dimensions and Weight .................................................................................................................................8 2.2.3 Ports...............................................................................................................................................................8 2.2.4 Environmental ................................................................................................................................................9 2.3 2760 + 2765 Antenna Unit – Wideband ..............................................................................................................10 2.3.1 Overview ......................................................................................................................................................10 2.3.2 Dimensions and Weight ...............................................................................................................................11 2.3.3 Antenna........................................................................................................................................................13 Zinwave 2700 DAS – Operational description Issue 1.0 April 11, 2007 ZINWAVE 2700 DAS - INSTALLATION AND TECHNICAL MANUAL Page iv Table of Figures Figure 1-1: Elements of standards-based structured/generic cabling..................................................................................1 Figure 2-1: Block diagram of the 2700 HU....................................................................................................................4 Figure 2-2: Front View of the 2700 Hub Unit.................................................................................................................5 Figure 2-3: Rear View of the 2700 Hub Unit. ................................................................................................................5 Figure 2-4: Connecting a pair of jumper leads from a RF transceiver...........................................................................7 Figure 2-5: Block diagram of the 2780/2781 SFP module. ...........................................................................................8 Figure 2-6: Block diagram of the 2760 AU. .................................................................................................................10 Figure 2-7: Block diagram of the 2765 AU. .................................................................................................................10 Figure 2-8: Front view of the 2760 AU. .......................................................................................................................11 Figure 2-9: Rear view of the 2760 AU.........................................................................................................................12 Figure 2-10: Front view of the 2765 AU. .......................................................................................................................12 Figure 2…

Text truncated - open the document above for the full version.

2700 Distributed Antenna System The Zinwave 2700 Distributed Antenna System (DAS) comprises a centrally located hub unit (HU) and remotely attached Antenna Units (AU). The hub is a 1U high 19” rack mount device supporting 4 RF service inputs and driving up to 8 independent AUs through fibre optic connections. The AU is housed in a small enclosure designed for un-obtrusive installation with separate antennas in an office environment. The Zinwave system is a simple 2 stage design, utilising multimode or single mode fibre cable to connect each AU to the Hub. Zinwave’s technology makes the use of conventional multimode fibre practical for wideband high frequency RF transmission. This patented technology enables the simultaneous transmission of multiple RF signals for different services over practical link lengths using low cost uncooled transceivers. Overcoming barriers to communication In-Building Cellular and Wireless Technology Features and specifications 2700 Hub Frequency Range 370MHz – 2.5GHz Interface for up to 8 optical transceiver outputs over MMF to remote AU Supports up to 4 concurrent RF services via 4 x RF input/outputs (SMA ports) 1U 19” rack mountable form factor Unique software programmable RF combiner architecture enabling wide variety of RF to antenna mappings MMF operating distances (from HU to AU) of at least 550m SNMP GUI-based and CLI-based network management RJ-45 Ethernet and Serial management interface Health monitoring capabilities for hub and remote DAS units www.zinwave.com In-Building Cellular and Wireless Technology RF Parameters Downlink MinTypMaxUnit System Bandwidth 3702500MHz RF input power -50+10dBm Max RF output power +12dBm Composite power at RU output (wideband) EVM degradation 13% At maximum wideband RU output power for 64-QAM 802.11g Wideband gain flatness -5+5dB Over full frequency range Single band gain flatness -2+2dB In any 100MHz band Wideband Spurious emissions -115dBm/Hz At RU output for maximum output power Return loss 1.5:1 * Assuming worst-case fibre loss Uplink MinTypMaxUnit System Bandwidth 3702500MHz Noise Figure* 1013dB Max RF input power -30-15dBm Input gain adjustment for minimum coupling loss System gain** -10+10dB 1dB adjustment steps Wideband gain flatness -5+5dB Over full frequency range Single band gain flatness -2+2dB In any 100MHz band * Assuming 300m multi-mode fibre, 15dB input gain ** Assuming worst-case fibre loss Fibre Optic Specifications Hub2675 Antenna Unit Number of Optical Ports 8 transceivers in industry standard, hot pluggable SFP form factor 1 transceiver, duplex SC connector Wavelength 1310nm Fibre types supported MM (both 50 and 62.5um) and SM cable 9/125um Fibre Distance (MM cable) At least 550m, dependent on fibre quality Fibre Distance (SM cable) At least 2km Laser safety classification Class 1 Features and specifications 2765 Antenna Unit Converts optical I/O to electrical I/O (SMA connector) powered via Power over Ethernet (remotely or using local PoE injector option Ceiling or wall mountable, can be located on wall or in roof space if required Multi-service capability e.g. TETRA, GSM, CDMA, TDMA, UMTS, iDEN, WLAN, WiMAX, LMR, PMR, SMR, Paging, DCS, EDGE, EVDO In-Building Cellular and Wireless Technology Power HubAntenna Unit Supply: 100 – 240 Volts, 50/60 Hz 100 – 240 Volts, 50/60 Hz or 40-76V DC (48V nominal) for PoE supply Consumption: 15W 15W Supervisory Network Management options SNMP v2 , CLI via Telnet & RS232 Remote via Hub Interface 100base-T Ethernet port and RS232 for CLI Physical Specifications Connectivity HubAntenna Unit RF connectors SMA (female) connectors, separate Tx and Rx; total of 4 RF I/O pairs 2 x SMA (female) connectors Optical connectors 8 x Pluggable SFP (1310nm), LC duplex connectors 1 x SC duplex connector Supervisory RJ45 (Ethernet), RS232 (CLI) Power IEC switched mains connector Power over Ethernet via RJ45 Dimensions HubAntenna Unit Width: 445mm (17.5 in), brackets for 19” rack mounting 120mm (4.75 in) Height: 44mm (1.8 in) 200mm (8.0 in) Depth: 270mm (10.6 in). 60mm (2.4 in) Weight: 3.5 kg 0.75 kg Environmental Specifications HubAntenna Unit Operating Temperature (Ambient, non-condensing) 0 to +55 degC 0 to +45 deg C Storage -25 to +55 degC -25 to +55 degC In-Building Cellular and Wireless Technology Standards & Approvals EMC, Regulatory & Safety Requirements EN 55022/CISPR22 FCC Part 15 Class A European EMC directive 89/336/EEC Electrical Safety EN 60950 NEC (National Electrical Code – US) UL 1950 Laser Safety BS EN 60825-1:2003 Safety of laser products Ordering Information Item codeDescriptionNotes Hub Items 2700 2700 Hub (HU) Basic Hub (without optical modules fitted) 2780 2.5GHz MM SFP Code for separate purchase of SFP modules to populate the hub (max 8 x SFP per hub) 9301 Mains lead, 2m, UK 9302 Mains lead, 2m, European Power over Ethernet via RJ45 9303 Mains lead, 2m, US AU Items 2765 High Power Antenna Unit, integrated optics 9322 PoE for AU (single), 2xRJ45, UK plug 9323 PoE for AU (single), 2xRJ45, EU plug 9324 PoE for AU (single), 2xRJ45, US plug Head Office Zinwave Ltd, Harston Mill, Harston, Cambridge CB22 7GG Tel: +44 (0)1223 875272 Fax: +44 (0)1223 875243 Email: [email protected] Ref: ZP400035-1.1

ZinWave Limited, Registered Office at Alder Castle, 10 Noble Street, London, EC2V 7QJ. Registered in England and Wales with Registered Number 4587255. VAT No: 834 9391 96 Zinwave Ltd Harston Mill Harston Cambridge CB22 7GG 11 April 2007 MPE Calculation for 2765 DAS System The FCC requires that the calculated MPE be equal to or less than a given limit dependent on frequency at a distance of 20 cm from a device to the body of a user. The overall transmitter frequency range of operation considered for the 2765 DAS Antenna Unit (AU) is 806MHz to 2500MHz. This covers GSM800, iDEN, PCS1900 and WLAN operating bands. The transmitter power value used is the maximum measured system average broadband power for all combinations of service feeds to the antenna. Each individual service is not capable of reaching this power. The equation for the MPE calculation is given in OET Bulletin 65, page 19 as: S = EIRP/4 π R 2 Where S = Power density EIRP = Effective Isotropically Radiated Power (EIRP = P x G) R = distance to the centre of radiation of the antenna Values Output power (P) : +12.0dBm (0.01585W) conducted max Antenna gain (G) : 8dBi (from 2700 DAS technical specification) R = 20cm Calculation S = EIRP/4 π R 2 S = 15.84 x 6.31 /(12.56 x 20 2 ) S = 0.02 mW/cm 2 ZinWave Limited, Registered Office at Alder Castle, 10 Noble Street, London, EC2V 7QJ. Registered in England and Wales with Registered Number 4587255. VAT No: 834 9391 96 For the 2700 DAS @ 806MHz at 20cm distance S = f/1500 mW/cm 2 (f = operating frequency) (from table 1 (b) - Limits for General Population/ Uncontrolled Exposure of FCC Rule Part 1.1310) S = 806/1500 = 0.537 mW/cm 2 For the 2700 DAS @ 1930MHz and 2500MHz at 20cm distance S = 1.0 mW/cm 2 (from table 1 (b) - Limits for General Population/ Uncontrolled Exposure of FCC Rule Part 1.1 S = 1.0 mW/cm 2 Conclusion The MPE value of the 2765 DAS at 20 cm meets the RF exposure limits.

TEST REPORT FROM RFI GLOBAL SERVICES LTD Test of: Zinwave Ltd Zinwave DAS 2765 To: FCC Part 90: 2006 (Subpart C) Test Report Serial No: RFI/RPTE1/RP48954JD18A This Test Report Is Issued Under The Authority Of Michael Derby, Wireless Group Leader Radio Performance: Tested By: Jamie Huckerby Checked By: Tony Henriques Report Copy No: PDF01 Issue Date: 04 April 2007 Test Dates: 14 March 2007 to 26 March 2007 This report is issued in Adobe Acrobat portable document format (PDF). It is only a valid copy of the report if it is being viewed in PDF format with the following security options not allowed: Changing the document, Selecting text and graphics, Adding or changing notes and form fields. This report may be copied in full. The results in this report apply only to the sample(s) tested. RFI GLOBAL SERVICES LTD TEST REPORT S.No. RFI/RPTE1/RP48954JD18A Page: 2 of 59 Issue Date: 04 April 2007 Test of: Zinwave Ltd Zinwave DAS 2765 To: FCC Part 90: 2006 (Subpart C) This page has been left intentionally blank. RFI GLOBAL SERVICES LTD TEST REPORT S.No. RFI/RPTE1/RP48954JD18A Page: 3 of 59 Issue Date: 04 April 2007 Test of: Zinwave Ltd Zinwave DAS 2765 To: FCC Part 90: 2006 (Subpart C) Table of Contents 1. Client Information......................................................................................................... 4 2. Equipment Under Test (EUT) ...................................................................................... 5 3. Test Specification, Methods and Procedures.......................................................... 10 4. Deviations from the Test Specification .................................................................... 11 5. Operation of the EUT during Testing ....................................................................... 12 6. Summary of Test Results .......................................................................................... 13 7. Measurements, Examinations and Derived Results ............................................... 14 8. Measurement Uncertainty ......................................................................................... 48 9. Measurement Methods .............................................................................................. 49 Appendix 1. Test Equipment Used ............................................................................... 56 Appendix 2. Test Configuration Drawings ................................................................... 57 RFI GLOBAL SERVICES LTD TEST REPORT S.No. RFI/RPTE1/RP48954JD18A Page: 4 of 59 Issue Date: 04 April 2007 Test of: Zinwave Ltd Zinwave DAS 2765 To: FCC Part 90: 2006 (Subpart C) 1. Client Information Company Name: Zinwave Ltd Address: Harston Mill Harston Cambridge CB2 5GG Contact Name: Mr A Bell RFI GLOBAL SERVICES LTD TEST REPORT S.No. RFI/RPTE1/RP48954JD18A Page: 5 of 59 Issue Date: 04 April 2007 Test of: Zinwave Ltd Zinwave DAS 2765 To: FCC Part 90: 2006 (Subpart C) 2. Equipment Under Test (EUT) The following information (with the exception of the Date of Receipt) has been supplied by the client: 2.1. Identification of Equipment Under Test (EUT) Description: Hub Unit (HU) Brand Name: Zinwave Model Name or Number: 2700 Serial Number: 0005256380 FCC ID Number: UPO2700 Country of Manufacture: England Date of Receipt: 23 March 2007 Description: Antenna Unit (AU) Brand Name: Zinwave Model Name or Number: 2765 Serial Number: 165 FCC ID Number: UPO2765 Country of Manufacture: England Date of Receipt: 23 March 2007 Description: Antenna Unit (AU) Brand Name: Zinwave Model Name or Number: 2765 Serial Number: 0702007 FCC ID Number: UPO2765 Country of Manufacture: England Date of Receipt: 23 March 2007 Description: Antenna Unit (AU) Brand Name: Zinwave Model Name or Number: 2765 Serial Number: 06120001 FCC ID Number: UPO2765 Country of Manufacture: England Date of Receipt: 23 March 2007 RFI GLOBAL SERVICES LTD TEST REPORT S.No. RFI/RPTE1/RP48954JD18A Page: 6 of 59 Issue Date: 04 April 2007 Test of: Zinwave Ltd Zinwave DAS 2765 To: FCC Part 90: 2006 (Subpart C) Identification of Equipment Under Test (EUT) (Continued) Description: Antenna Unit (AU) Brand Name: Zinwave Model Name or Number: 2765 Serial Number: 07020005 FCC ID Number: UPO2765 Country of Manufacture: England Date of Receipt: 23 March 2007 Description: Antenna Unit (AU) Brand Name: Zinwave Model Name or Number: 2765 Serial Number: 07020004 FCC ID Number: UPO2765 Country of Manufacture: England Date of Receipt: 23 March 2007 Description: Antenna Unit (AU) Brand Name: Zinwave Model Name or Number: 2765 Serial Number: 07020001 FCC ID Number: UPO2765 Country of Manufacture: England Date of Receipt: 23 March 2007 Description: Antenna Unit (AU) Brand Name: Zinwave Model Name or Number: 2765 Serial Number: 07020003 FCC ID Number: UPO2765 Country of Manufacture: England Date of Receipt: 23 March 2007 RFI GLOBAL SERVICES LTD TEST REPORT S.No. RFI/RPTE1/RP48954JD18A Page: 7 of 59 Issue Date: 04 April 2007 Test of: Zinwave Ltd Zinwave DAS 2765 To: FCC Part 90: 2006 (Subpart C) Identification of Equipment Under Test (EUT) (Continued) Description: Antenna Unit (AU) Brand Name: Zinwave Model Name or Number: 2765 Serial Number: 07020006 FCC…

Text truncated - open the document above for the full version.