USE901172Net2 PaxLock � 72mm Euro lock case

PAGE1 02/23/2012 Parts list Tools List Power Drill Drill bits 3 /8", 5 /8" Philips screwdriver Small flat blade terminal screwdriver Pencil 4mm Allen key (supplied) Technical Support Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST) [email protected] Ins-30168-US Net2 PaxLock Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/ Net2Air Site Surveyor (690-200-US). This access control unit uses wireless communication. It is recommended that a Net2Air site surveyor is used to determine the best position for the bridge and control units. This wireless unit requires a Net2Air bridge to communicate with the server PC. Paxton 1 2 3 4 56 7 8 9 AA AA - - + + 1) Front Lock Assembly 2) Rear Lock Assembly 3) Door Handle x 2 4) Mounting screw (1 1 /4") x 2 5) Mounting screw ( 1 1 /2") x 2 6) Mounting screw ( 1 3 /4" ) x 2 7) 8 mm Spindle 8) AA battery x 4 9) 4 mm Allen Key This unit requires Net2 v4.23 or later software. Call Technical Support if you require advice. PAGE2 The lock (not supplied) must first be fitted to the door. Slide the spindle through the lock to allow the template to locate over it. Ensure that the template is square to the door edge by using the top and bottom ruler scales. Mark the 2 x 3 /8" and 1 x 5 /8" holes. Remove the template and repeat the procedure for marking out the other side of the door. Installing the hardware Step 1 - Marking out Step 2 - Drilling Drill the 2 x 3 /8" holes for the mounting screws and 1 x 5 /8" hole for the wiring harness. To ensure accuracy you should drill these holes from both sides of the door towards the centre. This also avoids the risk of damaging the door face when the drill breaks through. Step 3 - Contact switch (optional) If a contact switch is to be fitted, an additional hole is required in the edge of the door. Drill a hole of the required size to receive the switch assembly. This should intersect the 5 /8" hole drilled previously to take the wiring harness. Feed the door contact wires through the door to exit on the inside. Ø 16 37 105 Ø 10 Paxton 706050403010 5 5 1515 020 2525 353545 5565754555 65 75 10203040607050 The spindle is locked into the front lock assembly by means of a spring loaded pin. Ensure that the spindle pin and the hole in the square drive are in alignment before depressing the pin and sliding the bar into the assembly. The pin will then latch into the hole securing the spindle in place. Step 4 - Attach the Spindle PAGE3 Step 9 - Fitting the rear cover Present the front lock assembly to the door passing the wiring harness through the 5 /8" hole. Present the rear lock assembly to the door and join the two parts together with the two mounting screws. Step 5 - Mounting on the door Step 6 - Wiring Plug the wiring harness into the socket in the rear lock assembly. Locate the top of the cover over the housing and push flush to the door. Clip in the 4 x AA batteries with reference to the label displayed below the holder assembly. Step 8 - Fitting the batteries Where a contact swich is fitted, connect the wires to the terminal block provided on the pcb. Step 7 - Wiring (contact switch option) Mounting screws are provided in three lengths. Short - Door width 1 1 /4" to 1 3 /4" Med - Door width 1 1 /2" to 2" Long - Door width 1 3 /4" to 2 1 /4" PAGE4 The current specification for compatible PC hardware, network and operating systems is available on our website at the following link: http://paxton.info/720 Net2 has NO PaxLock detection function. It is recognised that there could be security issues if the wireless units were detectable from outside the site. During installation, a PaxLock unit binds to a Net2Air bridge which will then only talk to registered units. Devices cannot be added to the system if commissioning mode is disabled. An entry is then made on the Doors screen and a special icon is used to denote the wireless connection. A PaxLock must bind to a Net2Air bridge before it will enrol itself onto the Net2 system. The term 'bind' is used to denote the fixed relationship between a wireless unit and its bridge. 1. Create a user record in the database and assign a Net2 token to the user. (This record can be deleted after the installation is complete.) 2. You must now wake up the PaxLock by using the front push button. 3. Present the user token to the PaxLock. 4. The Red and Green LED's will flash alternately while the unit configures. The PaxLock transmits the number and waits for a response from Net2. If more than one bridge replies, the unit checks the signal strength and selects the strongest bridge to communicate with. The Net2 software confirms that the token number is in the database and registers the PaxLock/bridge binding. The LED's will go out when the process has finished. The software must be in commissioning mode which is the default setting. If this has been turned off it must be enabled in the Server Configuration Utility. Enrolling a PaxLock The Net2 software should be loaded on the controlling PC with at least one Net2Air bridge installed. Full documentation is supplied with the Net2Air bridge unit and also from the website as follows: XAN1051 - Installing Net2 software < http://paxton.info/1520 > XIns-40084-US Net2Air USB bridge < http://paxton.info/1453 > XIns-40085-US Net2Air Ethernet bridge < http://paxton.info/1192 > Software installation Download the latest version of Net2 software at: http://paxton.info/1438 before commissioning this product. Step 10 - Fitting the handles Fit the two handles and secure with the grub screws provided. Check the mechanical operation of the lock and that the handles operate freely. Some of the Net2 features (e.g. Fire alarm integration, Anti-passback) are not available on this product as wireless communication is not suitable for data critical applications. PAGE5 Presenting a valid user token to the unit will cause the LED to briefly flash Green and the door will unlock. Th…

Text truncated - open the document above for the full version.

1(1) Declaration of Authorization: We Name: Paxton Access Ltd Address: Paxton House, Home Farm Road City: Brighton, East Sussex, BN1 9HU Country: UK Declare that: Name: RFI Global Services Ltd. Address: Pavilion A Ashwood Park, Ashwood Way Basingstoke, Hampshire RG23 8BG Is authorized to apply for Certification of the following product: FCC ID: USE901172 Product description: Net2 PaxLock - 72mm Euro lock case Type Designation: 901-172-US On our behalf. This is to certify that Paxton Access Ltd authorises RFI Global Services Limited to act on our behalf for the application of the EUT to RFI Global Services Ltd. Telecommunication Certification Body Section 5301 Certification: We certify that we are not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. § 862 because of a conviction for possession or distribution of a controlled substance. Date: 16 th March 2012 City: Brighton Name: Brett Glass Signature:

1(1) Application Examiner Telecommunication Certification Body RFI Global Services Ltd. Pavilion A Ashwood Park Basingstoke Hampshire RG23 8BG United Kingdom Re: Request for confidentiality 16 th March 2012 Applicant: Paxton Access Ltd FCC ID: USE901172 Model Number: 901-172-US To whom it may concern, Permanent Confidentiality Request is hereby submitted by Paxton Access Ltd to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:  Circuit Schematic, one file, eight pages.  Block diagram, one file, one page.  Operational/Functional Description, one file, three pages.  Parts lists, one file, one page. Rationale for request for confidentiality of all items above. Paxton Access Ltd has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Sincerely, Conformance Engineer Paxton Access Ltd

EXTERNAL PHOTOGRAPHS Front view (door entry unit) Front view (door exit unit) Side view Top view

FCC label Information Artwork for 901-172-US – Net2 PaxLock - 72mm Euro lock case Label Make-up Information Label dimensions: 30mm x 20mm Label material and print ribbon manufacturer: ZEBRA TECHNOLOGIES EUROPE LTD Label materials: Z Xtreme 4000T White with 3200 ribbon OR Z Ultimate 3000T White with 5095 ribbon. UL file number: PGJI2.MH18322 Label Location The ratings label is located on the inside of the battery compartment cover. Company ID (Paxton logo) is also located on the front of the unsecure assembly

INTERNAL PHOTOGRAPHS Main PCB – top view Main PCB – bottom view Hitag Interface PCB – top view Hitag Interface PCB – bottom view Hitag Interface PCB with 125kHz antenna Reader module – front view Reader module – back view Entry unit assembly with cover removed – showing reader module (potted) Side view (entry unit assembly only) Side view (entry and exit unit assemblies) – with covers removed Exit unit assembly – with batteries removed Exit unit assembly – battery compartment Back view (entry unit assembly) Back view (exit unit assembly)

TEST REPORT FROM RFI GLOBAL SERVICES LTD Test of: Net2 PaxLock FCC ID: USE901172 IC Certification Number: 10217A-901172 To: FCC Parts 15.209 and 15.215, Industry Canada RSS-Gen Sections 4.6 and 4.9 Test Report Serial No.: RFI-RPT-RP86275JD03A V2.0 Version 2.0 Supersedes All Previous Versions This Test Report Is Issued Under The Authority Of Chris Guy, Head of Global Approvals: pp Checked By: Ian Watch Signature: Date of Issue: 26 March 2012 This report is issued in Adobe Acrobat portable document format (PDF). It is only a valid copy of the report if it is being viewed in PDF format with the following security options not allowed: Changing the document, Selecting text and graphics, Adding or changing notes and form fields. This report may not be reproduced other than in full, except with the prior written approval of RFI Global Services Ltd. The results in this report apply only to the sample(s) tested. TEST REPORT SERIAL NO: RFI-RPT-RP86275JD03A V2.0 VERSION NO. 2.0 ISSUE DATE: 26 MARCH 2012 Page 2 of 13 RFI Global Services Ltd This page has been left intentionally blank. TEST REPORT SERIAL NO: RFI-RPT-RP86275JD03A V2.0 VERSION NO. 2.0 ISSUE DATE: 26 MARCH 2012 RFI Global Services Ltd Page 3 of 13 Table of Contents 1. Customer Information .................................................................................................................. 4 2. Summary of Testing ..................................................................................................................... 5 2.1. General Information 5 2.2. Summary of Test Results 5 2.3. Methods and Procedures 5 2.4. Deviations from the Test Specification 5 3. Equipment Under Test (EUT) ....................................................................................................... 6 3.1. Identification of Equipment Under Test (EUT) 6 3.2. Description of EUT 6 3.3. Modifications Incorporated in the EUT 6 3.4. Additional Information Related to Testing 6 3.5. Support Equipment 6 4. Operation and Monitoring of the EUT during Testing ............................................................... 7 4.1. Operating Modes 7 4.2. Configuration and Peripherals 7 5. Measurements, Examinations and Derived Results .................................................................. 8 5.1. General Comments 8 5.2. Test Results 9 5.2.1. Transmitter Radiated Spurious Emissions 9 5.2.2. Transmitter 20 dB Bandwidth 11 6. Measurement Uncertainty .......................................................................................................... 12 Appendix 1. Test Equipment Used ................................................................................................ 13 TEST REPORT SERIAL NO: RFI-RPT-RP86275JD03A V2.0 VERSION NO. 2.0 ISSUE DATE: 26 MARCH 2012 Page 4 of 13 RFI Global Services Ltd 1. Customer Information Company Name: Paxton Ltd. Address: Paxton House Home Farm Brighton Sussex BN1 9HU United Kingdom TEST REPORT SERIAL NO: RFI-RPT-RP86275JD03A V2.0 VERSION NO. 2.0 ISSUE DATE: 26 MARCH 2012 RFI Global Services Ltd Page 5 of 13 2. Summary of Testing 2.1. General Information Specification Reference: 47CFR15.209 & 47CFR15.215 Specification Title: Code of Federal Regulations Volume 47 (Telecommunications) 2011: Part 15 Subpart C (Intentional Radiators) - Sections 15.209 and 15.215 Specification Reference: RSS-Gen Issue 3 December 2010 Specification Title: General Requirements and Information for the Certification of Radio Apparatus Site Registration: FCC: 209735; Industry Canada: 3245B-2 Location of Testing: RFI Global Services Ltd, Wade Road, Basingstoke, Hampshire, RG24 8AH. Test Date: 05 March 2012 2.2. Summary of Test Results FCC Reference (47CFR) IC Reference Measurement Result Part 15.209 RSS-Gen 4.9/7.2.5 Transmitter Radiated Emissions Part 15.215 RSS-Gen 4.6.1/4.6.3 Transmitter 20 dB Bandwidth Key to Results = Complied = Did not comply 2.3. Methods and Procedures Reference: ANSI C63.4 (2009) Title: American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz Reference: ANSI C63.10 (2009) Title: American National Standard for Testing Unlicensed Devices 2.4. Deviations from the Test Specification For the measurements contained within this test report, there were no deviations from, additions to, or exclusions from the test specification identified above. TEST REPORT SERIAL NO: RFI-RPT-RP86275JD03A V2.0 VERSION NO. 2.0 ISSUE DATE: 26 MARCH 2012 Page 6 of 13 RFI Global Services Ltd 3. Equipment Under Test (EUT) 3.1. Identification of Equipment Under Test (EUT) Brand Name: Net2 PaxLock Model Name or Number: 901–172 Serial Number: 385875970 Hardware Version: z-pl01 rev 6, ppc-pl01 rev E FCC ID: USE901172 IC Certification Number: 10217A-901172 3.2. Description of EUT The equipment under test was a door lock with intelligent access control using an integrated 125 kHz proximity reader and IEEE 802.15.4, 2.4 GHz RF communications. The unit is powered by four AA batteries 3.3. Modifications Incorporated in the EUT No modifications were applied to the EUT during testing. 3.4. Additional Information Related to Testing Technology Tested: RFID Power Supply Requirement(s): Nominal 6 VDC Type of Unit: Transmitter Transmit Frequency: 125 kHz 3.5. Support Equipment The following support equipment was used to exercise the EUT during testing: Description: Net2Air USB Bridge Brand Name: Net2Air Model Name or Number: 477 - 268 Description: RFID tag Brand Name: Net2Air Model Name or Number: User4 TEST REPORT SERIAL NO: RFI-RPT-RP86275JD03A V2.0 VERSION NO. 2.0 ISSUE DATE: 26 MARCH 2012 RFI Global Services Ltd Page 7 of 13 4. Operation and Monitoring of the EUT during Testing 4.1. Operating Modes The EUT was tested in the following operating mode(s): • Continuously transmitting at maximum power at 125 kHz. 4.2. Configuration and Peripherals The EUT was tested in the following configuration(s): • The EUT was powered by four AA t…

Text truncated - open the document above for the full version.