V65E4810Feature Phone

Safety & warranty information. 2 Important Safety Information Important Safety Information 3 Important Safety Information This section contains important operational and safety information that will help you safely use your phone. Failure to read and follow the information provided in this section may result in serious bodily injury, death, or property damage. General Precautions There are several simple guidelines to operating your phone properly and maintaining safe, satisfactory service. • Speak directly into the mouthpiece. • Do not expose your phone to direct sunlight for extended periods of time (such as on the dashboard of a car). • Although your phone is quite sturdy, it is a complex piece of equipment and can be broken. Avoid dropping, hitting, bending, or sitting on it. • Any changes or modifications to your phone not expressly approved in this document could void your warranty for this equipment and void your authority to operate this equipment. Note: For the best care of your phone, only Kyocera- authorized personnel should service your phone and accessories. Failure to do so may be dangerous and void your warranty. Important Safety Information 3 Maintaining Safe Use of and Access to Your Phone Do Not Rely on Your Phone for Emergency Calls Mobile phones operate using radio signals, which cannot guarantee connection in all conditions. Therefore you should never rely solely upon any mobile phone for essential communication (e.g., medical emergencies). Emergency calls may not be possible on all cellular networks or when certain network services or mobile phone features are in use. Check with your local service provider for details. Using Your Phone While Driving Talking on your phone while driving (or operating the phone without a hands-free device) is prohibited in some jurisdictions. Laws vary as to specific restrictions. Remember that safety always comes first. Following Safety Guidelines To operate your phone safely and efficiently, always follow any special regulations in a given area. Turn your phone off in areas where use is forbidden or when it may cause interference or danger. Medical Devices If you have a medical device, including an implantable medical device such as a pacemaker or defibrillator, consult your healthcare provider and the device manufacturer’s directions before using this mobile phone. Persons with implantable medical devices: •Should always keep the mobile phone more than six (6) inches from the implantable medical device when the mobile phone is turned ON. •Should not carry the mobile phone in the breast pocket. •Should use the ear opposite the implantable medical device to minimize the potential for interference. •Should turn OFF the mobile phone immediately if you have any reason to suspect that interference is taking place. 4 Important Safety Information Important Safety Information5 Using Your Phone Near Other Electronic Devices Most modern electronic equipment is shielded from radio frequency (RF) signals. However, RF signals from wireless phones may affect inadequately shielded electronic equipment. RF signals may affect improperly installed or inadequately shielded electronic operating systems or entertainment systems in motor vehicles. Check with the manufacturer or their representative to determine if these systems are adequately shielded from external RF signals. Also check with the manufacturer regarding any equipment that has been added to your vehicle. Consult the manufacturer of any personal medical devices, such as pacemakers, defibrillator, and hearing aids, to determine if they are adequately shielded from external RF signals. Note: When using the phone in and near healthcare facilities, always determine the facility's policy concerning cell phone usage and request permission before using the phone near medical equipment. Using Your Phone On Airplanes On airplanes, follow applicable airline regulations and always follow the flight crew’s instructions concerning the use of your phone. Turning Off Your Phone in Dangerous Areas To avoid interfering with blasting operations, turn your phone off when in a blasting area or in other areas with signs indicating two-way radios should be turned off. Construction crews often use remote-control RF devices to set off explosives. Turn your phone off when you’re in any area that has a potentially explosive atmosphere. Although it’s rare, connecting or disconnecting accessories to your phone could generate sparks. Sparks can cause an explosion or fire, resulting in bodily injury or even death. These areas are often, but not always, clearly marked. They include: •Fueling areas such as gas stations •Below deck on boats Important Safety Information 5 •Fuel or chemical transfer or storage facilities •Areas where the air contains chemicals or particles such as grain, dust, or metal powders •Any other area where you would normally be advised to turn off your vehicle’s engine Note: Never transport or store flammable gas, flammable liquids, or explosives in the compartment of your vehicle that contains your phone or accessories. Note: Your phone complies with the Standards for Hazardous Location Equipment. Refer to the following section “Using Your Phone in Hazardous Locations” for details. Using Your Phone in Hazardous Locations Your phone complies with the Standards for Hazardous Location Equipment as a Nonincendive Electrical Equipment for use in a Class I, Division 2, Groups A, B, C, & D with a Temperature Code of T4. Precautions •Ensure that your phone is not exposed to the temperature outside the limits stated below. ▪Ambient Temperature: -4° F to 140° F (-20° C to 60° C) ▪Charging Temperature: 32° F to 113° F (0° C to 45° C) ▪Storage Temperature: ▪Less than one month: -4° F to 140° F (-20° C to 60° C) ▪More than one month: -4° F to 113° F (-20° C to 45° C) •Do not charge your phone in Division 2 hazardous locations. •Use only the charger provided with your phone: AC adapter SCP-47ADT and USB data cabl…

Text truncated - open the document above for the full version.

User Guide TOC i Table of Contents Introduction ................................................................................................................................ 1 Descriptions in the User Guide ........................................................................................... 1 Get Started ................................................................................................................................ 2 Phone Overview and Key Functions ................................................................................... 2 Set Up Your Phone ............................................................................................................. 7 Insert the Battery ......................................................................................................... 7 Charge the Battery ....................................................................................................... 9 Battery Capacity .......................................................................................................... 9 Remove the Battery ....................................................................................................10 Install a microSD Card and Reinstall SIM Card ...........................................................10 Turn Your Phone On and Off .............................................................................................12 Turn Your Phone On ...................................................................................................12 Turn Your Phone Off ...................................................................................................12 Setup Wizard .....................................................................................................................12 Set Up Voicemail ...............................................................................................................13 Phone Basics ............................................................................................................................14 Your Idle Screen ................................................................................................................14 Idle Screen Overview ..................................................................................................14 Status Bar ...................................................................................................................15 Notifications Screen ....................................................................................................17 Navigate Through the Menus .............................................................................................17 Select Menu Items ......................................................................................................17 Back Up Within a Menu ..............................................................................................18 Customize Main Menu Screen ....................................................................................18 Enter Text ..........................................................................................................................18 Key Function ...............................................................................................................18 Select a Text Input Mode ............................................................................................19 Enter Text Using XT9 Word ........................................................................................19 Enter Text Using Abc/ABC Mode ................................................................................20 Set Text Entry Options ................................................................................................20 TOC ii Copy and Paste Text ..................................................................................................20 Phone Calls ..............................................................................................................................22 Make Phone Calls ..............................................................................................................22 Call Using the Phone keypad ......................................................................................22 Call from Call History ..................................................................................................22 Call from Call History with the phone closed ...............................................................22 Call from Contacts ......................................................................................................22 Call Using a Speed Dial Number ................................................................................23 Call a Phone Number with Pauses .............................................................................23 Call Emergency Numbers ...........................................................................................24 Call Using Wi-Fi Calling ..............................................................................................24 Call Using Real Time Text (RTT) ................................................................................25 Receive Phone Calls ..........................................................................................................25 Answer an Incoming Call with the Phone Open ..........................................................25 Answer an Incoming Call with the Phone Closed ........................................................25 Answer an Incoming Call in Speakerphone Mode .......................................................25 Mute the Ringing Sound and Stop the Vibration .........................................................26 Send an Incoming Call to Voicemail ...........................................................................26 Reject an Incoming Call and Send a Message ..............................................…

Text truncated - open the document above for the full version.

KYOCERA International, Inc 8611 Balboa Avenue San Diego, CA 92123 Phone: 858-882-1400 Date: February 24, 2020 Federal Communications Commission 7345 Oakland Mills Road – Gate A Columbia MD 21046 Subject: Request for Confidentiality FCC ID: V65E4810 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. l Schematic Diagram l Block Diagram l Parts List l Tune-up Procedure l Operational Description l Software Operational Description The above mentioned documents contain detailed system and equipment descriptions that are considered to be proprietary information in the operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitors an unfair advantage in the market. In addition to the above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Authorizations. u External Photos u Internal Photos u Test Setup Photos u User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best regards, Douglas Dunn Deputy General Manager Regulatory Affairs

KYOCERA International, Inc 8611 Balboa Avenue San Diego, CA 92123 Phone: 858-882-1400 Date: February 24, 2020 To whom it may concern, Please be notified that I, Douglas Dunn, have designated Joanna Hung of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Joanna Hung of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan on the matters relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. As defined in 47 CFR Ch. 1.2002 (b), we further certify that neither the applicant nor any party to this application is subject to a denial to Federal benefits, including FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This authorization is limited to the product of as following: FCC ID: V65E4810 If you have any acknowledgement and response, please send it to Annie Cheng of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan directly. Should you have any question or comment regarding this matter, please do not hesitate to contact me. Sincerely yours, Douglas Dunn Deputy General Manager Regulatory Affairs

KYOCERA International, Inc 8611 Balboa Avenue San Diego, CA 92123 Phone: 858-882-1400 24 February 2020 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 Attn: Office of Engineering and Technology HAC Attestation - MIF for HAC RF Interference Evaluation To whom it may concern: This device, with FCC ID: V65E6910, will be certified to ANSI C63.19-2011 per Part 20.19. The M rating was determined by measuring the maximum steady state average E-field values in dB (V/m) as documented in the HAC report and adding the MIF value in dB (V/m) using pre-determined values provided by Speag under the below table: UID UID Version Communication System Name MIF (dB) 10460 AAA UMTS-FDD (WCDMA, AMR) -25.43 10225 CAB UMTS-FDD (HSPA+) -20.39 10170 CAE LTE-FDD (SC-FDMA, 1 RB, 20 MHz, 16-QAM) -9.76 10061 CAB IEEE 802.11b WiFi 2.4 GHz (DSSS, 11 Mbps) -2.02 10077 CAB IEEE 802.11g WiFi 2.4 GHz (DSSS/OFDM, 54 Mbps) 0.12 10427 AAB IEEE 802.11n (HT Greenfield, 150 Mbps, 64-QAM) -13.44 10069 CAC IEEE 802.11a/h WiFi 5 GHz (OFDM, 54 Mbps) -3.15 The Speag-reference documentation for supporting the pre-determined MIF value is Schmid & Partner Engineering AG, UID SUMMARY (Communication Systems for Calibration, Issued Date 2019/12/06) We confirm that the Speag MIF values provided represent all of the air interface modes applicable for a HAC rating for this handset. Sincerely, ____________________ Douglas Dunn Deputy General Manager Regulatory Affairs

Page 1 of 9 Report No.: 191211C18 CONSTRUCTION PHOTOS OF EUT Brand Name: Kyocera Model Name: E4810 Page 2 of 9 Report No.: 191211C18 Page 3 of 9 Report No.: 191211C18 Page 4 of 9 Report No.: 191211C18 Model Name: E4810NC Page 5 of 9 Report No.: 191211C18 Page 6 of 9 Report No.: 191211C18 Page 7 of 9 Report No.: 191211C18 Page 8 of 9 Report No.: 191211C18 Page 9 of 9 Report No.: 191211C18

KYOCERA International, Inc 8611 Balboa Avenue San Diego, CA 92123 Phone: 858-882-1400 FAX: 858-450-0134 FCC ID: V65E4810 Label Information Label Location Rear of Phone Battery Compartment FCC Label KYOCERA International, Inc 8611 Balboa Avenue San Diego, CA 92123 Phone: 858-882-1400 FAX: 858-450-0134 FCC ID: V65E4610 FCC declaration statement Kyocera complies with FCC rules Part 2.925(d) that the label shall be permanently affixed to the equipment and shall be readily visible to the purchaser at the time of purchase: 1. This cellular phone has limited label space on the exterior of the unit. The FCC ID label is placed in the battery compartment. 2. The phone will be marketed without the battery installed. The user will see the label when the user installs the battery. _________________________ Date: 2/24/20 Douglas Dunn Director of Regulatory Affairs Kyocera Corporation c / o Kyocera International, Inc.

Page 1 of 12 Report No.: 191211C18 CONSTRUCTION PHOTOS OF EUT Brand Name: Kyocera Model Name: E4810 Page 2 of 12 Report No.: 191211C18 WWAN Antenna BT/WLAN Antenna Page 3 of 12 Report No.: 191211C18 Page 4 of 12 Report No.: 191211C18 Page 5 of 12 Report No.: 191211C18 Page 6 of 12 Report No.: 191211C18 Page 7 of 12 Report No.: 191211C18 Page 8 of 12 Report No.: 191211C18 Page 9 of 12 Report No.: 191211C18 Page 10 of 12 Report No.: 191211C18 Page 11 of 12 Report No.: 191211C18 Page 12 of 12 Report No.: 191211C18 Model Name: E4810NC

SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 57 Report No. : SF191211C18 Issued Date : Jan. 22, 2020 SAR Test Report Report No. Applicant Address Product FCC ID : SF191211C18 : Kyocera Corporation c/o Kyocera International, Inc. : 8611 Balboa Avenue, San Diego, CA 92123 : Feature Phone : V65E4810 Brand : Kyocera Model No. : E4810, E4810NC Standards : FCC 47 CFR Part 2 (2.1093), IEEE C95.1:1992, IEEE Std 1528:2013 KDB 865664 D01 v01r04, KDB 865664 D02 v01r02, KDB 248227 D01 v02r02 KDB 447498 D01 v06, KDB 648474 D04 v01r03, KDB 941225 D01 v03r01 KDB 941225 D05 v02r05, KDB 941225 D06 v02r01 Sample Received Date : Dec. 11, 2019 Date of Testing : Jan. 08, 2020 ~ Jan. 16, 2020 Lab Address : No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location : No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City, Taiwan CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch–Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Gina Liu / Specialist Approved By : Gordon Lin / Manager FCC Accredited No.: TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 57 Report No. : SF191211C18 Issued Date : Jan. 22, 2020 Table of Contents Release Control Record ............................................................................................................................................................... 3 1.Summary of Maximum SAR Value ....................................................................................................................................... 4 2.Description of Equipment Under Test ................................................................................................................................. 5 3.SAR Measurement System ................................................................................................................................................... 6 3.1Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2SPEAG DASY6 System ............................................................................................................................................... 6 3.2.1 Robot ............................................................................................................................................................... 7 3.2.2 Probes ............................................................................................................................................................. 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................. 8 3.2.4 Phantoms ......................................................................................................................................................... 8 3.2.5 Device Holder .................................................................................................................................................. 9 3.2.6 System Validation Dipoles ............................................................................................................................. 10 3.2.7 Power Source ................................................................................................................................................ 10 3.2.8 Tissue Simulating Liquids .............................................................................................................................. 11 3.3SAR System Verification ............................................................................................................................................ 13 3.4SAR Measurement Procedure ................................................................................................................................... 14 3 .4.1 Area Scan and Zoom Scan Procedure .......................................................................................................... 14 3.4.2 Volume Scan Procedure ...........................................................................................…

Text truncated - open the document above for the full version.

Report No.: RF191211C18-5 Page No. 1 / 74 Report Format Version: 6.1.1 FCC Test Report (PART 22) Report No.: RF191211C18-5 FCC ID: V65E4810 Test Model: E4810 Series Model: E4810NC Received Date: Dec. 11, 2019 Test Date: Dec. 30, 2019 ~ Jan. 03, 2020 Issued Date: Jan. 16, 2020 Applicant: Kyocera Corporation c/o Kyocera International, Inc. Address: 8611 Balboa Avenue, San Diego, CA 92123 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location (1): No.19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan Test Location (2): B2F., No.215, Sec. 3, Beixin Rd., Xindian Dist., New Taipei City 231, Taiwan FCC Registration / Designation Number: 788550 / TW0003 427177 / TW0011 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies Report No.: RF191211C18-5 Page No. 2 / 74 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ........................................................................................................................... 5 2 Summary of Test Results ........................................................................................................................... 6 2.1 Measurement Uncertainty ..................................................................................................................... 6 2.2 Test Site and Instruments ..................................................................................................................... 7 3 General Information ................................................................................................................................... 8 3.1 General Description of EUT .................................................................................................................. 8 3.2 Configuration of System under Test ...................................................................................................... 9 3.2.1 Description of Support Units ....................................................................................................... 9 3.3 Test Mode Applicability and Tested Channel Detail ............................................................................ 10 3.4 EUT Operating Conditions .................................................................................................................. 12 3.5 General Description of Applied Standards and references................................................................. 12 4 Test Types and Results ............................................................................................................................ 13 4.1 Output Power Measurement ............................................................................................................... 13 4.1.1 Limits of Output Power Measurement ...................................................................................... 13 4.1.2 Test Procedures ........................................................................................................................ 13 4.1.3 Test Setup ................................................................................................................................. 14 4.1.4 Test Results .............................................................................................................................. 15 4.2 Modulation Characteristics Measurement .......................................................................................... 19 4.2.1 Limits of Modulation Characteristics ......................................................................................... 19 4.2.2 Test Setup ......................................…

Text truncated - open the document above for the full version.