VA5ANB300-2WLRKeyless Entry System

2-WAY REMOTE & Antenna STARTING SYSTEM WITH 1 BUTTONS FOR AUTOMATIC TRANSMISSION RE H300 -2WAY / ANT -2W DSS User Guide For Keyless Entry System The correspond remote with antenna is various WARNING It is the responsibility of the vehicle operator to ensure that their vehicle is par1<ed in a safe and responsible manner. 1. When leaving the vehicle, it is the user's resp onsibility to ensure that the gearshift lever is in "Park· in order to avoid accidents upon remote starting. (Note: Make sure that the automatic vehicle cannot start in ·onve·.) 2. It is the user's responsibility to ensure that the remote starter is disabled or put into valet mode before servicing. FCC COMPLIANCE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. and (2)This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void user's authority to operate this device. · F This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference. (2)This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)L’appareil ne doit pas produire de brouillage; (2)L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Using the remote control Description of Remote Appearance 2Way Remote 1Way Remote Button Functions Button Press buttons for LED Function Press 1time Lock Press 2 times Press 2times x 2 Unlock driver’s door Unlock all doors 2 seconds Remote start/stop Note: You make sure press button only after LED lighting ends to activate each feature properly. Lock, Unlock and Remote Starting icon is displaying with Two LED color. START/STOP: Note : Remote Engine Start - Press the button 1 time and then, within 3 seconds, press and hold the button for 2 seconds Remote Engine Stop - Press the button for 2 seconds Lock/Unlock Note: Press the button 1 time on the remote control transmitter to lock the vehicle. Press the button 2 times to unlock the driver’s door, 2 additional times to unlock all doors. Lock, Unlock and Remote Starting icon is displaying with One LED color. Vehicle Presets Heater When leaving the vehicle it is recommended to preset the accessory controls in preparation for the Next remote start. Settings for the blower motor(fan),front and rear (if equipped),should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM instead. Windshield Wipers, Headlights Certain vehicles require the windshield wipers and headlights circuits to become energized while running under remote start. When leaving the vehicle you must ensure that the windshield wipers and headlights switches are OFF. Leaving the headlights switch ON on certain types of vehicles could cause them to remain ON even after remote starter shutdown, resulting in a dead battery. Leave Windshield Wipers off to avoid damage wipers/motor with remote start. Changing the Remote Control Transmitter Battery Remote transmitter should be provided with two 3-volt lithium battery (Model: CR-2025). Please pay attention that with low battery LED in the remote might not work and the remote start distance might get shorter. Batteries can be purchased at any electronic device stores. Following the instructions below to change the remote control battery 1. You may use a coin to pry the remote control halves apart 2. Remove the old battery and replace with a new one 3. Be sure to observe the (+) sign when inserting the new battery. 4. Before assembling transmitter case, you should test the remote control. Note: LED icon of 2way transmitter indicates firstly blue color and then change to “RED” color when you press any button. In this case, it’s time to change CR2025 battery newly Description of Antenna Appearance 2Way Antenna Antenna Harness << Installation of Antenna >> Note: Use the power of the antenna car battery 12volts. The Antennas have been calibrated for horizontal installation at the left-top corner of the windshield. Remote-Starting your Vehicle Remote-Starting For the 2-way remote: 1. Press the button one time. The remote will beep once and display the Lock icon. Then, press the button within 2 seconds. The remote will beep once and display the KEY icon. 2. 5 seconds later, the remote will activate starter. The Key icon will be shown with 3 different tones of beeping then the LED Icon will be scrolled.. For the 1-way remote: 1. Press button one time and Lock LED will be displayed. Then pressbutton for 2 seconds within 3 seconds. 2. Remote Stop - Press button for 2 seconds. If your vehicle does not start at the first attempt, the system will shut down, wait a few seconds and try to start the engine again. There will be 3 start attempts before the system gives up. Note: Please make sure press to button only after LED lighting ends to activate each feature properly. Driving Off (Steps from Remote Start to Driving) With the vehicle running remotely, press button 2 times to disarm the OEM Starter Kill and/or the OEM alarm and unlock the doors. Enter the vehicle and do the following: 1. Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK position while the engine is running. This would cause the starter motor to reengage. Disarm the remote starter mode by pressing the foot brake) 2. …

Text truncated - open the document above for the full version.

SEGI LIMITED Date: 18th of May, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. UL Verification Services Inc. (formerly UL CCS) Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize UL-Korea and hereafter referred to as ULK, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL-Korea on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ULK as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, By Young il Chang President SEGI LIMITED REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

SEGI LIMITED UNIT S, 3-F, HARIBEST INDUSTRIAL BUILDING, 45-47, AU PUI WAN STREET, SHATIN, NT, HONGKONG Date: May 18, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: Request of Confidentiality for FCC ID: VA5ANB300-2WSS To Whom It may Concern: Pursuant to Sections 0.457 and 0.459 of the Commission`s Rules(CFR 47), and Section 552 (b) (4) of the Freedom of Information Act, SEGI LIMITED. Here by requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give SEGI LIMITED. temporary confidentiality of commercially sensitive information prior to product release. The requested permanent and Short-Term Confidential exhibits are listed as follows: PERMANENT & SHORT-TERM CONFIDENTIAL LIST Exhibit Description PERMANENT 1 Block Diagram 2 Schematics 3 Part Lists 4 Operation Description SHORT-TERM 5 NA 6 NA 7 NA 8 NA The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be public before the date of the Grant for this application. Sincerely, Young il Chang President

FCC ID : VA5ANB300-2WLR Page : 1 of 3 IC Num : 7087A-2WANB300LR UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 EXTERNAL PHOTOS OF EUT Top view of EUT Bottom view of EUT FCC ID : VA5ANB300-2WLR Page : 2 of 3 IC Num : 7087A-2WANB300LR UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 Front view of EUT Rear view of EUT FCC ID : VA5ANB300-2WLR Page : 3 of 3 IC Num : 7087A-2WANB300LR UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 Left side of EUT Right side of EUT

•Label and Location Label ANT-2WDSS SIZE ＊This label is attached to the back of the product and not easily removed. 15.7 X 8.9 mm

FCC ID : VA5ANB300-2WLR Page : 1 of 2 IC Num : 7087A-2WANB300LR UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 INTERNEL PHOTOS OF EUT EUT case open Main Board front side FCC ID : VA5ANB300-2WLR Page : 2 of 2 IC Num : 7087A-2WANB300LR UL Korea, Ltd. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 Main Board rear side Antenna

Antenna Pattern & Gain Report Model Name VerHorTotalVerHorTotal -9.7 dBi-7.9 dBi-6.0 dBi-3.6 dBi-0.8 dBi-0.7 dBi -9.2 dBi-7.8 dBi-5.6 dBi-3.2 dBi-0.4 dBi-0.4 dBi -9.3 dBi-7.8 dBi-5.7 dBi-3.3 dBi-0.6 dBi-0.5 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi -20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi-20.0 dBi Max Gain SEGI segi ANB300 Manufacturer Tester Name Test Date IF BW Port Power 5.30 dB Frequency EfficiencyDirectivityMax Position 907.000000 MHz Average Gain Theta155/Pie285 Meas Step 913.000000 MHz 919.000000 MHz 27.5 % 26.9 % 25.1 % Theta155/Pie285 Theta155/Pie285 5.20 dB 5.20 dB 2020-04-22 오후 3:16:45 100 Hz 0.00 dBm 15 ` Photo -20.0 dBi -15.0 dBi -10.0 dBi -5.0 dBi 0.0 dBi 5.0 dBi 10.0 dBi 123456789101112131415161718192021222324 Ver. -9.7-9.2-9.3-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20. Hor. -7.9-7.8-7.8-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20. Total -6.0-5.6-5.7-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.-20.

Portable deviceMobile device Simultaneous Transmitting MHz mm dBi =( ) = [ 0.21 + ( 200mm - 50mm ) X ( 919MHz / 150 ) ] = 919.2 Note. The calculation result was rounded to one decimal place for comparison. Maximum power densityNumeric power gain of the antenna Maximum power with turn-up toleranceDistance from transmitting antenna 2 ( f/1500 ) Copyright ⓒ 2018, UL Korea, Ltd. =0.008110 ㎽/㎝ 2 Conclusion:The exposure condition of this device is compliant with FCC rules. The limit for maximum permissible exposure =0.612666㎽/㎝ Maximum Permissible Exposure(MPE) evaluation for mobile device S = PG/( 4R 2 π) , ㎽/㎝ 2 S =G = P =R = Note. KDB 447498 D01 clasue 4.3.1 Step 2-1) SAR test exclusion thresholds for 100MHz to 1500MHz at test separationn distances > 50 mm [ Threshold at 50 mm + ( test separation distance - 50 mm ) X ( f(MHz ) / 150 ) ] mW → SAR evaluation for general population exposure conditions by measurement or numerical simulation is not required. 44.7mWTypical Power =Max.16.50dBmdBm - Max. Antenna Gain = -0.4 - Max. power with turn-up tolerance =16.50 - Min. test separation distance =200 FCC ID : VA5ANB300-2WLR Standalone SAR test exclusion considerations May 18, 2020 - Device category = - Transmitting mode =Single Transmitting - Max. transmitting frequency =919

Testing Laboratory TL-637 CERTIFICATION TEST REPORT Report Number. : 4789464423-FR1V3 Applicant : SEGI LIMITED Unit J2, 4/F, Block 1, Kinho Industrial Building, 14-24 Au Pui Wan Street, Shatin, New Territories HONGKONG, China Model : ANT-2WDSS FCC ID : VA5ANB300-2WLR IC : 7087A-2WANB300LR EUT Description : Keyless Entry System Test Standard(s) : FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-247 Issue 2 Date Of Issue: May 27, 2020 Prepared by: UL Korea, Ltd. 26th floor, 152, Teheran-ro, Gangnam-gu Seoul, 06236, Korea Suwon Test Site: UL Korea, LTD. Suwon Laboratory 218 Maeyeong-ro, Yeongtong-gu Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 REPORT NO: 4789464423-FR1V3 DATE: May 27, 2020 FCC ID: VA5ANB300-2WLR IC: 7087A-2WANB300LR Page 2 of 35 UL Korea, Ltd. Suwon Laboratory FORM ID: FCC_15C(03) 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 UL Korea, Ltd. Confidential This report shall not be reproduced except in full, without the written approval of UL Korea, Ltd. REPORT REVISION HISTORY Rev. Issue Date Revisions Revised By V1 05/21/20 Initial issue Robby Lee V2 05/26/20 Added the test description Robby Lee V3 05/27/20 Removed the average power section Robby Lee REPORT NO: 4789464423-FR1V3 DATE: May 27, 2020 FCC ID: VA5ANB300-2WLR IC: 7087A-2WANB300LR Page 3 of 35 UL Korea, Ltd. Suwon Laboratory FORM ID: FCC_15C(03) 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 UL Korea, Ltd. Confidential This report shall not be reproduced except in full, without the written approval of UL Korea, Ltd. TABLE OF CONTENTS REPORT REVISION HISTORY ................................................................................................. 2 TABLE OF CONTENTS ............................................................................................................ 3 1. ATTESTATION OF TEST RESULTS ................................................................................. 5 2. SUMMARY TABLE ............................................................................................................ 6 3. TEST METHODOLOGY ..................................................................................................... 7 4. FACILITIES AND ACCREDITATION ................................................................................. 7 5. CALIBRATION AND UNCERTAINTY ................................................................................ 8 5.1. MEASURING INSTRUMENT CALIBRATION ................................................................ 8 5.2. SAMPLE CALCULATION .............................................................................................. 8 5.3. MEASUREMENT UNCERTAINTY ................................................................................ 8 5.4. DECISION RULE .......................................................................................................... 8 6. EQUIPMENT UNDER TEST ............................................................................................... 9 6.1. EUT DESCRIPTION...................................................................................................... 9 6.2. MAXIMUM OUTPUT POWER ....................................................................................... 9 6.3. DESCRIPTION OF AVAILABLE ANTENNAS ............................................................... 9 6.4. WORST-CASE CONFIGURATION AND MODE ........................................................... 9 6.5. DESCRIPTION OF TEST SETUP ................................................................................10 7. MEASUREMENT METHOD...............................................................................................12 8. TEST AND MEASUREMENT EQUIPMENT ......................................................................13 9. ANTENNA PORT TEST RESULTS ...................................................................................14 9.1. ON TIME AND DUTY CYCLE ......................................................................................14 9.2. 99% BANDWIDTH .......................................................................................................15 9.3. 6 dB BANDWIDTH .......................................................................................................17 9.4. OUTPUT POWER ........................................................................................................19 9.5. POWER SPECTRAL DENSITY ...................................................................................21 9.6. CONDUCTED SPURIOUS EMISSIONS ......................................................................23 10. RADIATED TEST RESULTS ..........................................................................................25 10.1. LIMITS AND PROCEDURE ......................................................................................25 10.2. TRANSMITTER ABOVE 1 GHz ................................................................................27 10.3. WORST CASE BELOW 1 GHZ .................................................................................33 REPORT NO: 4789464423-FR1V3 DATE: May 27, 2020 FCC ID: VA5ANB300-2WLR IC: 7087A-2WANB300LR Page 4 of 35 UL Korea, Ltd. Suwon Laboratory FORM ID: FCC_15C(03) 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 UL Korea, Ltd. Confidential This report shall not be reproduced except in full, without the written approval of UL Korea, Ltd. 11. AC POWER LINE CONDUCTED EMISSIONS ...............................................................35 REPORT NO: 4789464423-FR1V3 DATE: May 27, 2020 FCC ID: VA5ANB300-2WLR IC: 7087A-2WANB300LR Page 5 of 35 UL Korea, Ltd. Suwon Laboratory FORM ID: FCC_15C(03) 218 Maeyeong-ro, Yeongtong-gu, Suwon-si, Gyeonggi-do, 16675, Korea TEL: (031) 337-9902 FAX: (031) 213-5433 UL Korea, Ltd. Confidential This report shal…

Text truncated - open the document above for the full version.

FCC ID: VA5ANB300-2WLR IC : 7087A-2WANB300LR Page 1 of 5 1. Appendix: TEST SETUP PHOTOS(Conducted Test) 1) CONDUCTED RF MEASUREMENT SETUP (DTS) CONDUCTED TEST PHOTO Page 2 of 5 2. Appendix: TEST SETUP PHOTOS(Radiated Test) 1) RADIATED RF MEASUREMENT SETUP (BELOW 1 GHz) BELOW 1 GHz FRONT TEST PHOTO BELOW 1 GHz REAR TEST PHOTO Page 3 of 5 2) RADIATED RF MEASUREMENT SETUP (ABOVE 1 GHz) ABOVE 1 GHz FRONT TEST PHOTO(X axis) ABOVE 1 GHz REAR TEST PHOTO(X axis) Page 4 of 5 3) RADIATED RF MEASUREMENT SET-UP (Axis) X AXIS PHOTO Y AXIS PHOTO Page 5 of 5 END OF REPORT Z AXIS PHOTO