VEG-LBT-HS310MBluetoothTM slim mono headset

Model:LBT-HS310M Brand:ELECOM Bluetooth headset Bluetooth™ headset connect with your cellular phone (with Bluetooth™ function) give you a safety way to none stop communication in driving. It supports NFC easy pairing function(Receive tag only).  Headset instruction: 1: Volume up 2: Volume down 3: mini USB jack. 4: Indicate LED 5: MFB button 6: Microphone 7. NFC area 1 2 3 5 6 4 4 5 4 7 Function Keys Location Keys Function Volume up Volume up or forward function Volume down Volume down or backward function MFB button Power on / off / Play/Pause/ call function LED indicators Color LED Status Function Blue Status LED flashes 2 times every 5 seconds Linked Status LED and Charging LED Flash alternative Pairing state Red Red LED flashes 1 time every 5 seconds Standby(no connection ) Charging LED flashes slowly every 3 seconds Low battery Charging LED lights up steady Charging (Indicator turns off when charging is completed.) How to start After opening the package, please make sure to do the following steps 1. Full charge the headset by charge it first time at least 2 hours. The Red LED will be steady on when charging. The LED will go off when battery is fully charged. Press MFB key about 3 seconds to power on the headset. When the headset power on the blue led will flash 3 times and you can hear a rising tone. When headset already power on, press MFB key about 3~5 seconds will power off the headset. When the headset power off the red led will flash 3 times and you can hear a falling tone. 2. Link (Pairing) headset to your Bluetooth™ mobile phone or other Bluetooth™ devices for the first time only. Press and hold the MFB button for three seconds to wait for the Blue led steady on that indicates the headset is into the paring mode. Operate your Bluetooth™ mobile phone or other Bluetooth™ device to start Bluetooth™ function. Find the headset “LBT-HS310M”, press the pairing code “0000” The blue LED is start flashing, the headset is in connected mode 3. Standby mode :  Double click MFB key to initiate voice dial  Long press main key to power off headset  Short press Vol+ and Vol- key to initiate Last Number redial  Short press MFB key for play/pause function  Long press MFB and Vol+ for proximity pairing  Long press MFB and Vol- for clear paired information 4. Music play:  Short press MFB key for play/pause function  Long press Vol+ key for forward function  Long press Vol- key for backward function 5. Incoming call:  Short press MFB key to accept call  Long press MFB key till hear beep tone to reject call 6. In Talking:  Short press volume up key to adjust volume up  Short press volume down key to adjust volume down  Long press MFB key to toggle call between headset and cellular phone  Short press MFB key to end call  long press Vol+ and Vol- to toggle microphone mute function 7. NFC easy pairing (Receive tag only).  Power On: Mobile phone short touch the BEC3470, blue and red LED flash alternatively for into pairing mode. You can auto-connect to the headset.  Connect: Mobile phone short touch with the BEC3470 when headset is disconnected  Power Off: Mobile phone short touch with the BEC3470 when headset is connected. 8. Led statuses POWER ON Blue led flash 3 times POWER OFF Red led flash 3 times PAIRING Blue and red led flash alternatively STANDBY MODE Red led flash once every 5 seconds A2DP SBC MODE Blue led flash twice every 5 seconds HEADSET ACTIVE MODE Blue led flash once( 1 second dim led)every 5 seconds LOW BATTERY INDICATION Red led flash twice every 3 seconds AUTO SHUTDOWN Red led flash 3 times and power off (5 minutes no any connection) 9. Troubleshooting If the Bluetooth Headset does not work, try the following: -Ensure connecting devices are charged -Turn off all devices and then turn them on in order to shown in this guide -Ensure devices are within 10 meter range -Ensure the Headset is connected by check the blue LED flash Note 1: Some A2DP source like 3.5mm interface transmitter cannot support AVRCP profile, so it cannot do remote control function. Note 2: Only cellular phone supports hands free profile can use voice dial, last number redial, call transfer function Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept …

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

Page 3 Page 4 Page 5 Page 6

FCC ID: VEG-LBT-HS310M Report No.: RF130321C17 OPERATIONAL DESCRIPTION The transmitter of the EUT (Bluetooth™ slim mono headset) is powered from 5Vdc from host equipment. The antenna is Chip antenna without antenna connector. For more detailed instruction, please take a look at the user’s manual.

Report No.: SA130321C17 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA130321C17 MODEL NO.: LBT-HS310M FCC ID: VEG-LBT-HS310M RECEIVED: Mar. 21, 2013 TESTED: Mar. 27 ~ Mar. 28, 2013 ISSUED: Apr. 03, 2013 APPLICANT: General Infinity Co., Ltd ADDRESS: 2F, No, 36, Reihu Street, Neihu District, Taipei, 114, Taiwan, ROC. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: SA130321C17 2 of 6 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .............................................................................................. 3 1. CERTIFICATION ........................................................................................................... 4 2. EVALUATION RESULT ................................................................................................. 5 3. SAR TEST EXCLUSION THRESHOLDS ..................................................................... 6 4. CONCLUSION .............................................................................................................. 6 Report No.: SA130321C17 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130321C17 Original release. Apr. 03, 2013 Report No.: SA130321C17 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT:Bluetooth™ slim mono headset MODEL NO.:LBT-HS310M BRAND:ELECOM APPLICANT:General Infinity Co., Ltd TESTED:Mar. 27 ~ Mar. 28, 2013 TEST SAMPLE:ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: LBT-HS310M) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Apr. 03, 2013 Suntee Liu / Specialist APPROVED BY: , DATE :Apr. 03, 2013 Ken Liu / Senior Manager Report No.: SA130321C17 5 of 6 Report Format Version 5.0.0 2. EVALUATION RESULT Following FCC KDB 447498 D01 “General SAR test exclusion guidance” The corresponding SAR Exclusion Threshold condition, listed below: 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR,16 where ¾ f(GHz) is the RF channel transmit frequency in GHz . ¾ Power and distanc e are rounded to the nearest mW and mm before calculation. ¾ The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2) At 100 MHz to 6 GHz and for test separation distances > 50 mm, the SAR test exclusion threshold is determined according to the following: a) [Threshold at 50 mm in step 1) + (test separation distance - 50mm)·( f(MHz)/150)] mW, at 100MHz to 1500 MHz b) [Threshold at 50 mm in step 1) + (test separation distance - 50 mm)·10] mW at > 1500 MHz and ≤ 6 GHz 3) At frequencies below 100 MHz, the following may be considered for SAR test exclusion. a) The threshold at the corresponding test separation distance at 100 MHz in step 2) is multiplied by [1 + log(100/f(MHz))] for test separation distances > 50 mm and < 200 mm. b) The threshold determined by the equation in a) for 50 mm and 100 MHz is multiplied by ½ for test separation distances ≤ 50 mm. c) SAR measurement procedures are not established below 100 MHz. When SAR test exclusion cannot be applied, a KDB inquiry is required to determine SAR evaluation requirements for any test results to be acceptable. Report No.: SA130321C17 6 of 6 Report Format Version 5.0.0 3. SAR TEST EXCLUSION THRESHOLDS Maximum measured transmitter power: Frequency (GHz) Max. Power (mW) Min. test separation distance (mm) SAR test exclusion calculation value (NOTE 2) 1-g extremity SAR test exclusion thresholds Result Bluetooth EDR 6.561 5 2.033 3 Pass Bluetooth LE 4.0 6.252 5 1.937 3 Pass NOTE: 1. The antenna type is Chip antenna with 1.5dBi gain. 2. Calculate SAR test exclus…

Text truncated - open the document above for the full version.

Report No.: RF130321C17 1 of 65 Report Format Version 5.0.0 FCC TEST REPORT REPORT NO.: RF130321C17 MODEL NO.: LBT-HS310M FCC ID: VEG-LBT-HS310M RECEIVED: Mar. 21, 2013 TESTED: Mar. 27 ~ Mar. 28, 2013 ISSUED: Apr. 03, 2013 APPLICANT: General Infinity Co., Ltd ADDRESS: 2F, No, 36, Reihu Street, Neihu District, Taipei, 114, Taiwan, ROC. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130321C17 2 of 65 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .......................................................................................... 6 1. CERTIFICATION ....................................................................................................... 7 2. SUMMARY OF TEST RESULTS .............................................................................. 8 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 9 3. GENERAL INFORMATION ..................................................................................... 10 3.1 GENERAL DESCRIPTION OF EUT ....................................................................... 10 3.2 DESCRIPTION OF TEST MODES ......................................................................... 11 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................... 12 3.3 DESCRIPTION OF SUPPORT UNITS ................................................................... 16 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................... 16 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 17 4. TEST TYPES AND RESULTS (FOR BLUETOOTH EDR) ...................................... 18 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................. 18 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 18 4.1.2 TEST INSTRUMENTS ........................................................................................... 19 4.1.3 TEST PROCEDURES ............................................................................................ 20 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 20 4.1.5 TEST SETUP ......................................................................................................... 21 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 21 4.1.7 TEST RESULTS ..................................................................................................... 22 4.2 CONDUCTED EMISSION MEASUREMENT ......................................................... 29 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 29 4.2.2 TEST INSTRUMENTS ........................................................................................... 29 4.2.3 TEST PROCEDURES ............................................................................................ 30 4.2.4 DEVIATION FROM TEST STANDARD .................................................................. 30 4.2.5 TEST SETUP ......................................................................................................... 31 4.2.6 EUT OPERATING CONDITIONS ........................................................................... 31 4.2.7 TEST RESULTS ..................................................................................................... 32 4.3 NUMBER OF HOPPING FREQUENCY USED ...................................................... 34 4.3.1 LIMIT OF HOPPING FREQUENCY USED ............................................................ 34 4.3.2 TEST SETUP ......................................................................................................... 34 4.3.3 TEST INSTRUMENTS ........................................................................................... 34 4.3.4 TEST PROCEDURES ............................................................................................ 34 4.3.5 DEVIATION FROM TEST STANDARD .................................................................. 34 4.3.6 TEST RESULTS ..................................................................................................... 34 4.4 DWELL TIME ON EACH CHANNEL ...................................................................... 36 4.4.1 LIMIT OF DWEL…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST