VIXRCQ500Wireless Charging Alarm Clock

Wireless charging alarm clock User’s Guide Getting Started Step 1: Install Batteries or Plug In Your can power your wireless charging alarm clock by installing 3 AAA batteries (not included) or by plugging the power adapter into a power outlet. To install batteries: 1. Open the battery compartment on the back of the clock. 2. Insert three AAA batteries (not included). Follow the + and – indications printed on the compartment. 3. Close the battery compartment. Note: When the clock is running on batteries alone (i.e., when it’s not plugged in), the display will time out after 15 seconds to extend battery life. To turn the display back on, press any clock button or make a sound next to the clock. Battery Precaution: Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with Local and National Regulations. To use the power adapter: 1. Plug the included power adapter into the DC 5V jack on the back of the clock. 2. Plug the other end into a power outlet. RCQ500 IB 01 Charging your Device IMPORTANT: Before you try to charge your device, make sure it is compatible with wireless charging. If your device has a metal case, remove it before you put the device on the char- ger. 1. Place your wireless charging-compatible device directly onto the charging pad on top of the clock. Refer to the placement illustrations here as a guide. Everyday Use Setting the Alarm 1. While the clock is displaying the time, press the SET button twice to go to the alarm display. - - A1 appears on the clock display. 2. Press and hold the SET button on the back of the clock until the hour digits start blinking. 3. Use the UP and DOWN buttons on back of the clock to adjust the hour for the alarm. Press the SET button to set it and move to the minutes. 4. Use the UP and DOWN buttons to adjust the minutes for the alarm. Press the SET button to set it. 5. The clock offers three alarms you can set for different times. If you’d like to set the other two alarms, follow steps 2–4 to set them. Otherwise, press the SET button twice to return to display the time again. To turn the alarm on/off: While the clock is displaying the time, press SET twice to display on A1 (or - - A1 if the alarm is not on). Press UP to turn the alarm on or off. The alarm indicator appears in the display when the alarm is on. Notes: • The alarm sounds for one minute when activated. • Press any button to activate snooze. The alarm indicator remains on the clock display. BATTERY BACKUP Your clock has a pre-installed battery backup that will keep the time in case power is interrupted (like by a power outage, for example). If you notice that battery backup is no longer working, simply replace the CR2032 coin-cell battery behind the AAA battery compartment. Remove the AAA batteries, then remove the small screw in the back of the AAA battery compartment to access the CR2032 battery compartment. Step 2: Set the Time When you first plug it in, the clock display shows 12:00. 1. While 12:00 is displayed, press and hold the SET button on the back of the clock to enter time set mode. 12Hr is displayed. 2. Press the UP or DOWN button on the back of the clock to switch between 12- and 24-hour time formats (for example, 5:00 pm in 12-hour format would be 17:00 in 24- hour format). By default, the clock uses the 12-hour format. Press SET to choose your preference and go to the next step. 3. Use the UP and DOWN buttons on back of the clock to adjust the hour. Press the SET button to set the hour and move to the minutes. 4. Use the UP and DOWN buttons to adjust the minutes. Then press SET to finish setting the time. Step 3: Set the Date 1. If the time is displayed, press the SET button to switch to date display. While the date is displayed, press and hold the SET button to enter date set mode. The year digits blink. 2. Use the UP and DOWN buttons on back of the clock to adjust the year. Press the SET button to set it and move to the month. 3. Use the UP and DOWN buttons to adjust the month. Press the SET button to set it and move to the date. 4. Use the UP and DOWN buttons to adjust the date. Then press SET to finish setting the date. Check your device’s screen to see the progress of charging. You can remove your device at any time during charging. 2. When your device is completely charged, remove it from the charging pad. Note: The clock must be plugged in to provide wireless charging. Tour of the Wireless Charging Alarm Clock Back DOWN button adjusts the flashing value when setting the Time, Date, or Alarm. It also accesses display time- out (press) and changes between Fahrenheit and Celsius temperature display (press and hold). UP button adjusts the flashing value when setting the Time, Date, or Alarm. It also accesses and changes the display mode setting. SET button switches the clock display between time, date, and alarm status. Press and hold to adjust the currently displayed parameter. To p Wireless charging pad lets you charge compatible devices wirelessly when the clock is using AC power. Display PM indicator shows that the time displayed is PM (does not apply to 24-hour format). Time/date digits show the current time, date, display mode, or Time/Alarm setting values. Alarm indicator shows that an alarm is set. Temperature shows the current ambient temperature. Alarm indicator Alarm indicator PM indicator Battery compartment DC 5V Jack Clock, back panel Using Display Time-Out You can set the clock so that it automatically turns off its display after several seconds. The display comes back on when it senses a sufficiently loud sound. To turn display time-out on/off: Press DOWN. The press DOWN again to toggle between time-out on (on Sd) and off (- - Sd). Switching Temperature Display Between Celsius and Fahrenheit By default, the clock displays temperature in degrees Fahrenheit. To switch between degrees Fahrenheit and Celsius: Press and hold the DOWN button on the back of the clock. Changing the Display Mode The wireless …

Text truncated - open the document above for the full version.

Company: Voxx Accessories Corp. Ad d: 3502 Woodview Trace, suite 220, Indianapolis, Indiana 46268 United States Tel: (317)218-7301 Extension: 7301 Fax : 317 569 1307 E-mail: [email protected] DECLARATION Dear Sir or Madam: We, Voxx Accessories Corp, h ereby declare that product name: Wireless charging alarm clock(model name: RCQ500, S718, S5014, S7 012. FCC ID: VIXRCQ500). These models are electrically identical with the same electromagnetic emissions and electromagnetic co mpatibility characteristics. RCQ500 has been tested by BACL. The differences of them are as follows: Model name. Please contact me if there is need for any additional clarification or information. Best Regards, FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 74 35 Oa kland Mills Road Columbia, MD 21046 Signature: Typed or Printed Name: Paul Tinaphong Title: VP engineering

Company: Voxx Accessories Corp. Add: 3502 Woodview Trace, suite 220, Indianapolis, Indiana 46268 United States Tel: (317)2 18-7301 Extension: 7301 Fax: 317 569 1307 Date:2020-05-27 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Voxx Accessories Corp., hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Typed or Printed Name: Paul Tinaphong Title: VP engineering FCC Authorization

Co mpany: Voxx Accessories Corp. A dd: 3502 Woodview Trace, suit e 220, Indianapolis, Indiana 46268 United States T el: (317)218-7301 Extension: 7301 Fax: 317 569 1307 E-mail: [email protected] FCC Confidential Authorization Date: 2020-05-27 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: VIXRCQ500 To: whom it may concern, In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Voxx Accessories Corp. hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: Typed or Printed Name: Paul Tinaphong Title: VP engineering

EXHIBIT A - EUT EXTERNAL PHOTOGRAPHS

Wireless charging alarm clock

EXHIBIT B - EUT INTERNAL PHOTOGRAPHS Antenna

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. FCC PART 15C TEST REPORT For Voxx Accessories Corp. 3502 Woodview Trace, suite 220, Indianapolis, Indiana 46268 United States FCC ID: VIXRCQ500 Report Type: Original Report Product Type: Wireless charging alarm clock Test Engineer: Winnie Yang Re port Number: RXM200527050-00B Re port Date: 2020-06-11 Reviewed B y: Oscar Ye EMC Manager Prepared By: Bay Area Compliance Laboratories Corp. (Kunshan) No.248 Chenghu Road,Kunshan,Jiangsu province,China Tel: +86-0512-86175000 Fax: +86-0512-88934268 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RXM200527050-00B FCC Part 15C Page 2 of 21 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 3 TEST METHODOLOGY .................................................................................................................................................. 4 MEASUREMENT UNCERTAINTY .................................................................................................................................... 4 TEST FACILITY ............................................................................................................................................................. 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 EUT EXERCISE SOFTWARE .......................................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 5 EXTERNAL I/O CABLE .................................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULTS ............................................................................................................................... 7 TEST EQUIPMENT LIST ........................................................................................................................................... 8 FCC §1.1310 & §2.1091–MAXIMUM PERMISSIBLE EXPOSURE (MPE) ............................................................... 9 APPLICABLE STANDARD .............................................................................................................................................. 9 EUT SETUP ................................................................................................................................................................ 10 RESULT ...................................................................................................................................................................... 10 TEST DATA ................................................................................................................................................................ 11 FCC §15.203 - ANTENNA REQUIREMENT ........................................................................................................... 12 APPLICABLE STANDARD ............................................................................................................................................ 12 ANTENNA CONNECTOR CONSTRUCTION .................................................................................................................... 12 FCC §15.207 (a) – AC LINE CONDUCTED EMISSIONS ..................................................................................... 13 APPLICABLE STANDARD ............................................................................................................................................ 13 EUT SETUP ................................................................................................................................................................ 13 EMI TEST RECEIVER SETUP ....................................................................................................................................... 13 TEST PROCEDURE ...................................................................................................................................................... 13 FACTOR & OVER LIMIT CALCULATION ...................................................................................................................... 14 TEST RESULTS SUMMARY .......................................................................................................................................... 14 TEST DATA .....................................…

Text truncated - open the document above for the full version.

EXHIBIT C - TEST SETUP PHOTOGRAPHS Conducted Emissions (Front View) Conducted Emissions (Side View) Radiated Emissions View (Below 30MHz) Radiated Emissions View (Above 30MHz) H-Filed Strength View Position A H-Filed Strength View Position B H-Filed Strength View Position C H-Filed Strength View Position D H-Filed Strength View Position E E-Filed Strength View Position A E-Filed Strength View Position B E-Filed Strength View Position C E-Filed Strength View Position D E-Filed Strength View Position E