VPE-SMN826SMARTNODE

SMN-826 Instruction Manual WARNINGS For customer in the U.S.A and Canada • You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. • Operation is subject to the following two conditions: 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device. • This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For customer in Europe • This equipment has been tested and found to comply with the limits set out in the R&TTE Directive. • Where you see this symbol on any of our electrical products/packaging in Europe, it means that at end of life the product/battery must be disposed of in accordance with any applicable laws or requirements for the separate disposal of electrical equipment/batteries. • The manufacturer of this product is CADI Scientific Pte Ltd, 31 Ubi Road 1, #03-00 Aztech Building, Singapore 408694. PRECAUTIONS • Connect only recommended power supply to unit. • Mount unit securely. USAGE The SMN-826 SmartNODE transmits LF and UHF signals continuously. It is designed to work with other devices in the SmartSense system. The SMN-826 contains a PIR motion sensor to detect human presence. The LF signal starts transmitting continuously on detection of human presence and can be received by some devices such as SmartTAG STG-85x. The UHF signal is a beacon transmitted every 1 minute to let other devices such as SmartNODE STG-890, for the SmartSense system to know its status. SETUP The SMN-826 requires external power supply for it to function. This can be provided by a suitable adapter (e.g. 12vdc 1A) as shown. Once plugged in, the SMN-826 will automatically be turned on. When motion sensor has detected human presence, it will blink its LED to indicate operation. SPECIFICATIONS Power 12v dc Power consumption Max 12VA External dimensions (excluding maximum projecting parts) 87 x 147 x 41 mm Mass Approx. 220 g (0.5 lb) Operating temperature 20°C - 50°C (68°F - 122°F) Storage/transport temperature 10°C - 50°C (50°F - 122°F) Inputs/outputs DC connector x1 Terminal block x1 Supplied accessories None Transmission frequency 868.4 MHz (For customer in Europe) 919.8 MHz (For customer in U.S.A) 925.0 MHz (For customer in U.S.A) 125 kHz (all regions) Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. (15.21) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.(15.19(a)(3))

Global Certification Corp. PHOTO OF EUT PHOTOS OF EUT Global Certification Corp.Report No. : 091601 PHOTO OF EUT PHOTO OF EUT : 1 of 4 Front View of EUT 1 Front View of EUT 1 Global Certification Corp.Report No. : 091601 PHOTO OF EUT PHOTO OF EUT : 2 of 4 Rear View of EUT 1 Inside View of EUT 1-1

Label location

Global Certification Corp. PHOTO OF EUT Rear View of EUT 1 Inside View of EUT Global Certification Corp. PHOTO OF EUT Component Side of Main Board 1 Solder Side of Main Board 1 125 kHz Ant. 900MHz Ant. Global Certification Corp. PHOTO OF EUT Component Side of Main Board 2 Solder Side of Main Board 2

Global Certification Corp. Date of Issue: Oct.12.,2010 Report No:F091601 Page1/57 FCC 47 CFR PART 15 SUBPART C TEST REPORT FOR Product Name: SmartNODE Model : SMN-826; SMN-826 (919); SMN-826 (925) Trade Name: CADI Issued to CADI SCIENTIFIC PTE LTD. 31 Ubi Road 1, # 03-00 Aztech Building Singapore 408694 Issued by Global Certification Corp. EMI Test Site Sansia Lab NO.34-3,Zihhe Rd.,Sansia Township,Taipei County 237, Taiwan ,R.O.C. EMC Test Site Sijhih office and Lab No. 146. Sec.2. Siangjhang Rd. Sijhih City. Taipei County 221, Taiwan(R.O.C.) Note: This test refers exclusively to the test presented test model and sample. This report shall not be reproduced except in full, without the written approval of Global Certification Corporation. This document may be altered or revised by Global Certification Corporation. Personnel only, and shall be noted in the revision section of the document. Global Certification Corp. Date of Issue: Oct.12.,2010 Report No:F091601 Page2/57 TABLE OF CONTENTS ----------------------------------------------------------------------------------------------------- 2 1. GENERAL INFORMATION -------------------------------------------------------------------------------------------------------- 3 1.1 DESCRIPTION OF THE TESTED SAMPLES----------------------------------------------------------------------------------------------- 4 2. TEST METHODOLOGY ------------------------------------------------------------------------------------------------------------- 4 2.1 GENERAL TEST PROCEDURES --------------------------------------------------------------------------------------------------- 4 2.2 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ----------------------------------------------------------------- 5 2.3 DESCRIPTION OF TEST MODES -------------------------------------------------------------------------------------------------- 5 2.4 DESCRIPTION OF THE SUPPORT EQUIPMENTS ----------------------------------------------------------------------------- 6 3. TEST AND MEASUREMENT EQUIPMENT ----------------------------------------------------------------------------------- 8 3.1 CALIBRATION----------------------------------------------------------------------------------------------------------------------- 8 3.2 EQUIPMENT-------------------------------------------------------------------------------------------------------------------------- 8 4. SECTION 15.209 REQUIREMENTS FOR 125kHZ (FUNDAMENTAL/ HARMONICS) ----------------------------- 9 4.1 TEST SETUP------------------------------------------------------------------------------------------------------------------------- 9 4.2 LIMIT-------------------------------------------------------------------------------------------------------------------------------10 4.3 TEST PROCEDURE-----------------------------------------------------------------------------------------------------------------11 4.4 RESULT: PASSED ----------------------------------------------------------------------------------------------------------------11 4.5 TEST DATA: ------------------------------------------------------------------------------------------------------------------------11 5. SECTION 15.249 REQUIREMENTS (FUNDAMENTAL/ HARMONICS) ----------------------------------------------18 5.1 TEST SETUP------------------------------------------------------------------------------------------------------------------------18 5.2 LIMIT-------------------------------------------------------------------------------------------------------------------------------18 5.3 RESULT: PASSED --------------------------------------------------------------------------------------------------------------18 5.4 TEST DATA: ------------------------------------------------------------------------------------------------------------------------18 6. 20dB BANKWIDTH ------------------------------------------------------------------------------------------------------------------44 6.1 TEST SETUP------------------------------------------------------------------------------------------------------------------------44 6.2 TEST PROCEDURE-----------------------------------------------------------------------------------------------------------------44 6.3 TEST DATA: ------------------------------------------------------------------------------------------------------------------------44 7. SECTION 15.209 REQUIREMENTS (GENERAL RADIATED EMISSION) -------------------------------------------47 7.1 TEST SETUP------------------------------------------------------------------------------------------------------------------------47 7.2 LIMIT-------------------------------------------------------------------------------------------------------------------------------48 7.3 TEST PROCEDURE-----------------------------------------------------------------------------------------------------------------49 7.4 TEST SPECIFICATION--------------------------------------------------------------------------------------------------------------49 7.5 RESULT: PASSED ----------------------------------------------------------------------------------------------------------------49 7.6 TEST DATA: ------------------------------------------------------------------------------------------------------------------------50 8. SECTION 15.207 REQUIREMENTS (POWERLINE CONDUCTED EMISSIONS) ----------------------------------55 8.1 TEST SETUP------------------------------------------------------------------------------------------------------------------------55 8.2 TEST SETUP------------------------------------------------------------------------------------------------------------------------55 8.3 LIMIT-------------------------------------------------------------------------------------------------------------------------------55 8.4 TEST PROCEDURE-----------------------------------------------------------------------------------------------------------------55 8.5 TEST SPECIFICATION----------------------------------…

Text truncated - open the document above for the full version.

Global Certification Corp. Appendix 1 PHOTOS OF TEST CONFIGURATION Global Certification Corp. Report No. : F072902 Appendix 1 : 1 of 9 Horizontal Polarization and the EUT place to the X axis (9kHz to 30MHz) Horizontal Polarization and the EUT place to the Y axis (9kHz to 30MHz) Global Certification Corp. Report No. : F072902 Appendix 1 : 2 of 9 Horizontal Polarization and the EUT place to the Z axis (9kHz to 30MHz) Vertical Polarization and the EUT place to the X axis (9kHz to 30MHz) Global Certification Corp. Report No. : F072902 Appendix 1 : 3 of 9 Vertical Polarization and the EUT place to the Y axis (9kHz to 30MHz) Vertical Polarization and the EUT place to the Z axis (9kHz to 30MHz) Global Certification Corp. Report No. : F072902 Appendix 1 : 4 of 9 Horizontal Polarization and the EUT place to the X axis (30MHz to 1GHz) Horizontal Polarization and the EUT place to the Y axis (30MHz to 1GHz) Global Certification Corp. Report No. : F072902 Appendix 1 : 5 of 9 Horizontal Polarization and the EUT place to the Z axis (30MHz to 1GHz) Vertical Polarization and the EUT place to the X axis (30MHz to 1GHz) Global Certification Corp. Report No. : F072902 Appendix 1 : 6 of 9 Vertical Polarization and the EUT place to the Y axis (30MHz to 1GHz) Vertical Polarization and the EUT place to the Z axis (30MHz to 1GHz) Global Certification Corp. Report No. : F072902 Appendix 1 : 7 of 9 Horizontal Polarization and the EUT place to the X axis (1GHz to 10GHz) Horizontal Polarization and the EUT place to the Y axis (1GHz to 10GHz) Global Certification Corp. Report No. : F072902 Appendix 1 : 8 of 9 Horizontal Polarization and the EUT place to the Z axis (1GHz to 10GHz) Vertical Polarization and the EUT place to the X axis (1GHz to 10GHz) Global Certification Corp. Report No. : F072902 Appendix 1 : 9 of 9 Vertical Polarization and the EUT place to the Y axis (1GHz to 10GHz) Vertical Polarization and the EUT place to the Z axis (1GHz to 10GHz)