VRA-SG9011098SG901-1098 802.11b/g/n Module

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: VRA-SG9011098 FCC Rule Part: 15.247 ACS Project Number: 11-0244 Manufacturer: Sagrad Model: SG901-1098 Manual Sagrad DOC # 906-0009 Installation / Users Manual For: 802.11 B/G/N WiFi Module Model SG901-1098 Sagrad Inc. Corporate Headquarters and Service 751 North Drive, Suite 10 Melbourne, FL 32934 PH# 321-255-0515 Fax 321-214-0315 www.Sagrad.com THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.” Sagrad DOC # 906-0009 Product Description You have purchased an 802.11 B/G/N module. This module is designed to be used with different types of processors (Blackfin, Samsung, etc) and in different types of applications (medical, industrial, etc). For information on how to integrate the SW and Hardware for this module into the final product please contact Sagrad Inc. Warning: This device must be used with the following approved antennas: 1. MFG: Pulse Antennas Part#: W1037 2. MFG: Pulse Antennas Part#: W1038 3. MFG: Sagrad SG901-1066 Use of any other antenna may violate you local government requirements such as the FCC or IC. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. NOTE: “This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.” Warning: Changes or modifications to this device not expressly approved by Sagrad could void the user’s authority to operate the equipment. Class B Device: “NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.” Modular Approved Device : Please make sure to add a label on the outside of the final product showing that the unit contains the FCC approved device. See below for exact information on the label. Contains FCC ID: VRA-SG9011098 Sagrad DOC # 906-0009 Limited Warranty Sagrad Inc. (“Sagrad”) warrants this Product (including any accessories) against defects in material or workmanship as follows: • LABOR: For the period of one (1) year from the date of purchase, if this product is determined to be defective, Sagrad will repair or replace the Product, as its option, at no charge, or pay labor charges to any Sagrad authorized service facility. After the warranty Period, the customer is liable for all labor charges. • PARTS: In addition, Sagrad will supply, at no charge, new or rebuilt replacements in exchange for defective parts for the period of one (1) year. After the warranty period, the customer is liable for all parts. • ACCESSORIES: Parts and Labor for all accessories are for the period of one (1) year. Limitations to this limited warranty : 1. This warranty extends to the original consumer purchaser only and is not assignable or transferable. 2. This warranty shall not apply to any Product which has been subjected to misuse, abuse, abnormal use, negligence, alteration or accident, or has its serial number altered or removed. 3. This warranty does not apply when the user has disregarded instructions for installation and use of the product. 4. This warranty does not apply to water or liquid damage of any kind. 5. This warranty does not apply to any defects or damage directly or indirectly caused by or resulting from the use of unauthorized replacement parts and/or service performed by unauthorized personnel. 6. This warranty does not apply to the instruction manual . THIS WARRANTY IS MADE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER OBLIGATIONS ON THE PART OF SAGRAD, INC. PROVIDED, HOWEVER, THAT IF THE DISCLAIMER OF IMPLIED WARRANTIES IN INEFFECTIVE UNDER APPLICABLE LAW, THE DURATION OF ANY IMPLIED WARRANTIES ARISING BY OPERATION OF LAW SHALL BE LIMITED TO ONEE (1) YEAR FROM THE DATE OF PURCHSE OR SUCH LONGER PERIOD AS MAY BE REQUIRED BY APPLICABLE LAW. SAGRAD, INC. HEREBY DISCLAIMS ANY AND ALL LIABILITY FOR CONSEQUENTIAL AND INCIDENTILA DAMAGES ARISING OUT OF OR IN CONNECTION WITH ANY BREACH OF THIS WARRANTY OR ANY OTHER CLAIM WITH RESPECT TO THIS PRODUCT, INCLUDING BUT NOT LIMITED TO, CLAIMS OF NEGLIGENCE, STRICT LIABILITY IN TORT OR BREACH OF CONTRACT. SOME STATES DO NOT ALLOW (A) LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR (B) THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS…

Text truncated - open the document above for the full version.

5015 B. U. Bowman Dr. Buford, GA 30518 October 11, 2011 ACS TCB 5015 B.U. Bowman Drive Buford, GA 30518 Re: FCC ID: VRA-SG9011098 To Whom It May Concern: The following application is submitted on behalf of our client, Sagrad, Inc., for evaluation of their model SG901-1098 for certification under FCC Part 15.247. The SG901-1098 is a 802.11b/g/n module which is designed to be used with different types of processors and in different types of applications. The module is a fully integrated wireless radio including a RF synthesizer/VCO, high speed data converters, digital baseband processors, power management and power amplifier. The SG901-1098 was tested in full to the requirements of the aforementioned rules and was found to be in compliance. Sincerely, Sam Wismer Vice President, Technology Advanced Compliance Solutions, Inc.

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: VRA-SG9011098 FCC Rule Part: 15.247 ACS Project Number: 11-0244 Manufacturer: Sagrad Model: SG901-1098 External Photos Model: SG901-1098 FCC ID: VRA-SG9011098 ACS Project: 11-0244 Advanced Compliance Solutions Page 2 Figure 1: External Photo – Front Figure 2: External Photo – Front Close-up Model: SG901-1098 FCC ID: VRA-SG9011098 ACS Project: 11-0244 Advanced Compliance Solutions Page 3 Figure 3: External Photo – Front Close-up Model: SG901-1098 FCC ID: VRA-SG9011098 ACS Project: 11-0244 Advanced Compliance Solutions Page 4 Figure 4: External Photo – Back

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: VRA-SG9011098 FCC Rule Part: 15.247 ACS Project Number: 11-0244 Manufacturer: Sagrad Model: SG901-1098 Label Information

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: VRA-SG9011098 FCC Rule Part: 15.247 ACS Project Number: 11-0244 Manufacturer: Sagrad Model: SG901-1098 Internal Photos Model: SG901-1098 FCC ID: VRA-SG9011098 ACS Project: 11-0244 Advanced Compliance Solutions Page 2 Figure 1: Internal Photo – Front – Shield Removed Figure 2: Internal Photo – Front – Shield Removed Close-up Model: SG901-1098 FCC ID: VRA-SG9011098 ACS Project: 11-0244 Advanced Compliance Solutions Page 3 Figure 3: Internal Photo – Back

3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Certification Exhibit FCC ID: VRA-SG9011098 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 11-2058 Manufacturer: Sagrad Model: SG901-1098 RF Exposure Model: SG901-1098 FCC ID: VRA-SG9011098 General Information: Applicant: Sagrad ACS Project: 11-2058 Device Category: Mobile Environment: General Population/Uncontrolled Exposure Technical Information: Antenna Type: Sagrad 3.8 dBi SG901-1066 PCB Antenna, 2.4 - 2.5 GHz Pulse 3.2 dBi W1037 1/4 dipole antenna, 2.4 - 2.5 GHz Pulse 4.9 dBi W1038 1/4 dipole antenna, 2.4 - 2.5 GHz Antenna Gain: Sagrad 3.8 dBi SG901-1066 PCB Antenna Pulse 3.2 dBi W1037 1/4 dipole antenna Pulse 4.9 dBi W1038 1/4 dipole antenna Maximum Transmitter Conducted Power: 23.27 dBm Maximum System EIRP: 28.17 dBm, 656.145 mW Exposure Conditions: Greater than 20 centimeters MPE Calculation The Power Density (mW/cm 2 ) is calculated as follows: S = 2 4R PG π Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) MPE Calculator for Mobile Equipment Limits for General Population/Uncontrolled Exposure* 243723.271.00212.324.93.090 200.131 Power Densit y (mW/cm^2) Distance (cm) Transmit Frequency (MHz) Radio Power (dBm) Power Density Limit (mW/Cm2) Radio Power (mW) Antenna Gain (dBi) Antenna Gain (mW eq.) Installation Guidelines The installation manual should contain text similar to the following advising how to install the equipment to maintain compliance with the FCC RF exposure requirements: RF Exposure In accordance with FCC requirements of human exposure to radio frequency fields, the radiating element shall be installed such that a minimum separation distance of 20 centimeters will be maintained. Conclusion This device complies with the MPE requirements by providing adequate separation between the device, any radiating structure and the general population. ACS Project: 11-2058 Advanced Compliance Solutions Page 2

3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Certification Test Report FCC ID: VRA-SG9011098 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 11-2058.W03.12.C Manufacturer: Sagrad Model: SG901-1098 Test Begin Date: June 29, 2011 Test End Date: October 21, 2011 Report Issue Date: October 28, 2011 FOR THE SCOPE OF ACCREDITATION UNDER CERTIFICATE NUMBER AT-1533 This report must not be used by the client to claim product certification, approval, or endorsement by ACLASS, ANSI, or any agency of the Federal Government. Project Manager: Reviewed by: Thierry Jean-Charles Kirby Munroe EMC Engineer Director, Wireless Certifications Advanced Compliance Solutions, Inc. Advanced Compliance Solutions, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 53 pages TABLE OF CONTENTS 1 GENERAL ......................................................................................................3 1.1 Purpose .............................................................................................................................................. 3 1.2 Product description .......................................................................................................................... 3 1.3 Test Methodology and Considerations ........................................................................................... 4 2 TEST FACILITIES ..........................................................................................5 2.1 Location ............................................................................................................................................. 5 2.2 Laboratory Accreditations/Recognitions/Certifications ............................................................... 5 2.3 Radiated & Conducted Emissions Test Site Description .............................................................. 6 3 APPLICABLE STANDARD REFERENCES...................................................8 4 LIST OF TEST EQUIPMENT..........................................................................9 5 SUPPORT EQUIPMENT ..............................................................................10 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ............................10 7 SUMMARY OF TESTS .................................................................................11 7.1 Antenna Requirement – FCC: Section 15.203 ............................................................................. 11 7.2 6 dB Bandwidth - FCC: Section 15.247(a)(2) IC: RSS-210 A8.2(a) ........................................... 12 7.3 Peak Output Power - FCC Section 15.247(b)(3) IC: RSS-210 A8.4(4)....................................... 18 7.4 Band-Edge Compliance and Spurious Emissions-FCC 15.247(d) IC: RSS-210 A8.5............... 24 7.5 Power Spectral Density - FCC Section 15.247(e) IC: RSS-210 A8.2(b) ..................................... 43 7.6 Power Line Conducted Emissions – FCC: Section 15.207 IC: RSS-Gen 7.2.4 .......................... 49 8 CONCLUSION..............................................................................................52 Model: SG901-1098 FCC ID: VRA-SG9011098 ACS Report: 11-2058.W06.12.C Advanced Compliance Solutions Page 3 of 53 1 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of Federal Regulations and Industry Canada’s Radio Standards Specification for modular approval. 1.2 Product description The Sagrad SG901-1098 is a 802.11b/g/n module which is designed to be used with different types of processors and in different types of applications. The module is a fully integrated wireless radio including a RF synthesizer/VCO, high speed data converters, digital baseband processors, power management and power amplifier. Technical Details: Operating Range: 2412GHz – 2462MHz Number of Channels: 11 Modulation: 802.11b: DSSS (BPSK / QPSK / CCK); 802.11g: OFDM (BPSK / QPSK / 16QAM / 64QAM) 802.11n: OFDM (BPSK / QPSK / 16QAM / 64QAM) Data Rate: 802.11b: 11, 5.5, 2, 1 Mbps; 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps; 802.11n: 65, 58.5, 52, 39, 26, 19.5, 13, 6.5 Mbps RF Connector: U-FL. Antenna / Gain: Sagrad 3.8 dBi SG901-1066 PCB antenna, 2.4 - 2.5 GHz Pulse 3.2 dBi W1037 1/4 dipole antenna, 2.4 - 2.5 GHz Pulse 4.9 dBi W1038 1/4 dipole antenna, 2.4 - 2.5 GHz Input Voltage: 3.5 VDC Manufacturer Information: Sagrad, Inc. 751 North Drive, Suite 10 Melbourne, FL 32934-9289 Phone: (321) 255-0513 Test Sample Serial Number(s): N/A Test Sample Condition: The sample provided was in good operating condition with no noticeable physical damage. Model: SG901-1098 FCC ID: VRA-SG9011098 ACS Report: 11-2058.W06.12.C Advanced Compliance Solutions Page 4 of 53 1.3 Test Methodology and Considerations The Sagrad SG901-1098 was evaluated for compliance to the radiated and RF conducted emissions requirements at three channels corresponding to the lower, middle and higher channels operating in the 2.4 GHz ISM band for all three available modes of operation. The unit was connected to an evaluation board through a SDIO board. Additionally, the radiated spurious emissions evaluation was performed with the SG901-1098 in two antenna configurations: W1038 Pulse external antenna and an SG901-1066 Sagrad PCB antenna. The EUT was setup in the orientation of typical installation. The table below reports the EUT configurations leading to the highest emissions. Table 1.3-1: EUT Evaluation Configuration Mode of Operation Channel Frequency (MHz) Test Utility Power Setting (dBm) Data Rates 1 2412 10 6 2437 10 802.11b 11 2462 10 1 Mbps 1 2412 13 6 2437 18 802.11g 11 2462 12 6 Mbps 1 2412 13 6 2437 18 802.11n 11 2462 12 6.5 Mbps The unintentional emissions data for the evaluation of the SG9…

Text truncated - open the document above for the full version.

3998 FAU Blvd. Suite 310 Boca Raton, FL 33431 Tel: 561-961-5585 Fax: 561-961-5587 Certification Exhibit FCC ID: VRA-SG9011098 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Project Number: 11-2058 Manufacturer: Sagrad Model: SG901-1098 Test Set Up Photos Model(s): SG901-1058 FCC ID: VRA-SG9011098 ACS Project: 11-2058 Advanced Compliance Solutions Page 2 Figure 1: Radiated Emissions With Dipole Antenna– Back View Model(s): SG901-1058 FCC ID: VRA-SG9011098 ACS Project: 11-2058 Advanced Compliance Solutions Page 3 Figure 2: Radiated Emissions With Dipole Antenna– Front View Model(s): SG901-1058 FCC ID: VRA-SG9011098 ACS Project: 11-2058 Advanced Compliance Solutions Page 4 Figure 3: Radiated Emissions With PCB Antenna– Back View Model(s): SG901-1058 FCC ID: VRA-SG9011098 ACS Project: 11-2058 Advanced Compliance Solutions Page 5 Figure 4: Radiated Emissions With PCB Antenna– Front View Model(s): SG901-1058 FCC ID: VRA-SG9011098 ACS Project: 11-2058 Advanced Compliance Solutions Page 6 Figure 5: Radiated Emissions With PCB Antenna– Top View Model(s): SG901-1058 FCC ID: VRA-SG9011098 ACS Project: 11-2058 Advanced Compliance Solutions Page 7 Figure 6: RF Conducted Emissions Model(s): SG901-1058 FCC ID: VRA-SG9011098 ACS Project: 11-2058 Advanced Compliance Solutions Page 8 Figure 7: Power Line Conducted Emissions – Front View Model(s): SG901-1058 FCC ID: VRA-SG9011098 ACS Project: 11-2058 Advanced Compliance Solutions Page 9 Figure 8: Power Line Conducted Emissions – Side View