VUDAUTOPRO2011Car DVD Player with Monitor

AUXUSB COLOR TFT LCD 7.0TOUCH Monitor HS70I Touch Screen TABLE OF CONTENTS TABLE OF CONTENTS Important safety instruction........................................................................................ Product description.................................................................................................... Connect cable............................................................................................................ The IR Remote Control............................................................................................... Touch menu............................................................................................................... Setup menu............................................................................................................... IR headphone use manual............................................................................................ Preparation before operation...................................................................................... Specifications........................................................................................................... Compatible disk types................................................................................................ How to deal with disc.................................................................................................. 1 2 3 4 5 10 20 21 22 23 24 The design and specifications of this manual may not match with the real, final interpretation of all the Division. Note: 241 Dear Customer We thank you for purchasing the Multimedia . We wish you many pleasant hours of watching DVD's or listening to your favorite music. Personal Safety has been taken in consideration in the design and manufacturing this product, however any improper use or operation may result in an electrical shock, fire and/or any other hazards. To prevent these hazards it is strongly recommended to read this manual thoroughly and adhere to the following precautions: Important Safety Instructions Important Safety Instructions NOTE - Please dispose empty batteries according the regulations in your country - All On Screen Displays (OSD) and Pictures will be based on the English version. - Design and Specifications may vary in the manual from the actual product in use. CAUTIONCAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintena- nce (servicing) instructions in the literature accompanying the applia- nce. The unit employs a laser system. To ensure proper use of this product. Please read this owners manual carefully and retain for future reference. Should the require maintenance, contact an authorized service location-see ser- vice procedure. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation may be present when the enclosure is opened. Do not stare into beam. CAUTION: WARNING: FCC regulations state that any change or modification to the equipment, not expressly approved by maker or its authorized parties, could void user's authority to operate this equipment. Attention: Do not write on the unlabeled side of the disc. Do not use chemical solutions to clean the DVD disc. Do not stick labels or glue-based notes on the disc. Do not use disks with glue residue or damaged labels. Do not use anti-scratchingmaterials or covers, that were not designed for this machine. Do not put or store disk in the following environments: Directly under the sunlight, in moist or dusty environments or beside heating elements. How to hold disc Do not touch the unlabeled side of the disc.. When there are stains on face of disc Wipe gently with a wet cloth and then with dry one. When a disc is brought in from a cold environment to a hot one, condensation can form on the face of the disc. Wipe down with a soft, smooth, dry cloth before using. How to deal with disc Load one disc with the data side facing upwards and make sure you do not touch the data side with your fingers. Disc loading Once the disc is loaded, the unit will automatically start reading the disk and it will take a few seconds to download the disc initial data, thereafter the disc type will be displayed in the left upper corner of the LCD screen and the unit will start playing the disc. EJECT 223 PRODUCT DESCRIPTION (1) Power (2) Indicator light when the machine have electric, it as red light,playing it turn off (3) (8)Infra-Red Audio transmitter: 2.3MHz/2.8MHz &3.2MHz/3.8MHz (4) LCD screen COMPATIBLE DISK TYPESCOMPATIBLE DISK TYPES Some DVD discs may have special requirements for playing, with which this system may not be compatible. Please refer to the specifications on the individual disc. About 700MB - 300 minutes DISC TYPE DVD CD-DA MP3 Content Size Total Play time About 4.7 GB - 2hrs. (Single side & single layer) About 8.5 GB - 4hrs. (Single side & double layer) About 9.4 GB - 4hrs. (Double side & Single layer) AUDIO/ VIDEO 12CM About 17GB - 8hrs. (Double side & double layer) AUDIO 12CM About 700MB - 74 minutes MP3 AUDIO12CM Discs types The Multimedia Player can play the following types of discs: DVD / CD / CD-R / CD-RW / DVD-R / DVD-RW / DVD+R / DVD+RW. Discs other than listed above cannot be played. Please do NOT play discs smaller than 12CM or of odd shapes, only play sound 12CM discs. The Multi…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 Shenzhen Autopro Technology Co., Ltd. August 18, 2011 To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, ___ Shenzhen Autopro Technology Co., Ltd._______hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): (Car DVD Player with Monitor, HS70I, HS90I, MP261，VW270D ，ATP20，ATP20D, AD463，JD2605, SKD270D) We affirm that between SIEMIC and __ Shenzhen Autopro Technology Co., Ltd. ___, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Yuqing Yin / Manager Assistant Phone : +86-755-27651188 / Bldg H2 Area A Hongfa Technology Industrial Zone Shiyan Town Bao An District Shenzhen China

Company Name: Shen Zhen Autopro Technology Co., Ltd. Company Address: Bldg H2, Area A, Hongfa Technology Industrial Zone, Shiyan Town, Bao An District, Shenzhen, China 1) How does this device operate? Play DVD disk, Read USB, SD card and input AV signal and powered from Car Cigarette lighter.. 2) Provide information on the device and its antenna. The transmitter’s antenna is a flexible cable sodered on the PCB, this is permanently attached antenna and meets the requirements of the section. 3) How is it installed? The EUT will be installed in a car. And power by 12Vdc Car Power. 4) What test procedure was used? Operating condition is according to ANSI C63.4-2009 5) If tested in a car, how was it configured/tested? N/A 6) Was the tuning range properly verified? The test lab should indicate in the report that the tuning controls were manually adjusted to verify maximum tuning range. EUT was adjusted to work at the selected channels: 88.5 MHzand 89.9 MHz. The EUT will not allow operation below 88.1 MHz and will not allow operation above 107.9 MHz. 7) Was the bandwidth properly tested with maximum audio input? Emissions from the intentional radiator shall be confined within a band 200 kHz wide centered on the operation frequency. The 200 kHz band shall lie wholly within the frequency range of 88 – 108 MHz. Setup the EUT and simulators as shown in the report. Enable RF signal and confirm EUT active. Modulate output capacity of EUT up to specifications. 8) Provide the test report. Test Report Submitted Signature: Name: Yuqing Yin Date: 18, August, 2011

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (current) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 1.0 2.0 August – 11 - 2008 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 2.0 Shenzhen Autopro Technology Co., Ltd. August 31, 2011 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: VUDAUTOPRO2011 We hereby request confidential treatment of information accompanying this application as outlined below: - Schematics - Operational Description - Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Yuqing Yin / Manager Assistant Phone : +86-755-27651188 / Bldg H2 Area A Hongfa Technology Industrial Zone Shiyan Town Bao An District Shenzhen China

SHEN ZHEN AUTOPRO TECHNOLOGY CO., LTD. Car DVD Player with monitor FCC ID：VUDAUTOPRO2011 Model：HS70I; Input: DC 12V, 2.5A This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions(1) This device may not cause harmful interference,and(2)this device must accept any interference received, Including interference that may cause undesired operation

Mark Location: FCC ID Label Location

ISO/IEC17025 Accredited Lab. Report No: FCC 1107193 File reference No: 2011-08-17 Applicant: SHEN ZHEN AUTOPRO TECHNOLOGY CO., LTD. Product: Car DVD Player with monitor Model No: HS70I Trademark: VIZUALOGIC Test Standards: FCC Part 15 Subpart C, Paragraph 15.239 Test result: It is herewith confirmed and found to comply with the requirements set up by ANSI C63.4&FCC Part 15 Subpart C, Paragraph 15.239 regulations for the evaluation of electromagnetic compatibility Approved By Jack Chung Manager Dated: August 17,2011 Results appearing herein relate only to the sample tested The technical reports is issued errors and omissions exempt and is subject to withdrawal at SHENZHEN TIMEWAY TECHNOLOGY CONSULTING CO LTD 5/F,Block 4, Anhua Industrial Zone.,No.8 TaiRan Rd.CheGongMiao,FuTian District, Shenzhen,CHINA. Tel (755) 83448688 Fax (755) 83442996 Report No: 1107193 Page 2 of 29 Date: 2011-08-17 TEST REPORT The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Special Statement： The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19. The testing quality system of our laboratory meets with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L2292 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:1999 General Requirements) for the Competence of testing Laboratories. FCC-Registration No.: 899988 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. Registration No.:899988. IC- Registration No.: IC5205A-01 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. The acceptance letter from the IC is maintained in our files. Registration No.: IC 5205A-01. Report No: 1107193 Page 3 of 29 Date: 2011-08-17 TEST REPORT The report refers only to the sample tested and does not apply to the bulk. This report is issued in confidence to the client and it will be strictly treated as such by the Shenzhen Timeway Technology Consulting Co .,Ltd. It may not be reproduced rather in its entirety or in part and it may not be used for adverting. The client to whom the report is issued may, however, show or send it . or a certified copy there of prepared by the Shenzhen Timeway Technology Consulting co .,Ltd to his customer. Supplier or others persons directly concerned. Shenzhen Timeway Technology Consulting co .,Ltd will not, without the consent of the client enter into any discussion of correspondence with any third party concerning the contents of the report. In the event of the improper use of the report. The Shenzhen Timeway Technology Consulting co .,Ltd reserves the rights to withdraw it and to adopt any other remedies which may be appropriate. Test Report Conclusion Content 1.0 General Details ................................................................................................ 4 1.1 Test Lab Details................................................................................................ 4 1.2 Applicant Details.............................................................................................. 4 1.3 Description of EUT .......................................................................................... 4 1.4 Submitted Sample............................................................................................. 4 1.5 Test Duration.................................................................................................... 5 1.6 Test Uncertainty.................................................................................................5 1.7 Test By.......................................................................................................... 5 2.0 List of Measurement Equipment......................................................................... 5 3.0 Technical Details............................................................................................. 7 3.1 Summary of Test Results..................................................................................... 7 3.2 Test Standards.................................................................................................. 7 4.0 EUT Modification............................................................................................. 7 5.0 Power Line Conducted Emission Test...................................................................... 8 5.1 Schematics of the Test........................................................................................ 8 5.2 Test Method and Test Procedure............................................................................ 8 5.3 Configuration of the EUT.................................................................................... 8 5.4 EUT Operating Condition...................…

Text truncated - open the document above for the full version.