W3QWIFIHDDP700Portable Wi-Fi HDD

RV-0000000 Project No.: 1505C169 Page 2 of 14 RV-0000000 Project No.: 1505C169 Page 3 of 14

RV-0000000 Project No.: 1505C169 Page 4 of 14 RV-0000000 Project No.: 1505C169 Page 5 of 14 RV-0000000 Project No.: 1505C169 Page 6 of 14 RV-0000000 Project No.: 1505C169 Page 7 of 14 RV-0000000 Project No.: 1505C169 Page 8 of 14 RV-0000000 Project No.: 1505C169 Page 9 of 14 RV-0000000 Project No.: 1505C169 Page 10 of 14 SAMSUNG/ST1000LM024 RV-0000000 Project No.: 1505C169 Page 11 of 14 SAMSUNG/ST2000LM003 RV-0000000 Project No.: 1505C169 Page 12 of 14 HGST/ HTS541010A9E680 RV-0000000 Project No.: 1505C169 Page 13 of 14 RV-0000000 Project No.: 1505C169 Page 14 of 14

Report No. 2015SAR256 Page 2 / 61 V4.0 Standards Conclusion Localized Specific Absorption Rate (SAR) of this equipment has been measured in all cases requested by the relevant standards above. Maximum localized SAR is below exposure limits as well. Applicable Limit Regulations ANSI/IEEE C95.1-2005 Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields. 3 kHz to 300 GHz ANSI/IEEE C95.3-2002 Recommended Practice For Measurements and Computations of Radio Frequency Electromagnetic Fields with Respect to Human Exposure to such Fields. 100 kHz-300 GHz Applicable Standards IEEE Std 1528™-2003: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques KDB865664 D01v01r03: SAR Measurement Requirements for 100 MHz to 6 GHz KDB447498 D01v05r02: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Polices KDB248227 D01v02r01: SAR Measurement Procedures for IEEE 802.11 Wi-Fi Transmitters Report No. 2015SAR256 Page 3 / 61 V4.0 Change History Version Change Contents Author Date V1.0 First edition Chen Qiang 2015-06-15 V2.0 Revise by KDB248227 D01v02r01 and IEEE1528-2003 Chen Qiang 2015-07-09 V3.0 Revise by KDB248227 D01v02r01 and IEEE1528-2003 Chen Qiang 2015-08-23 V4.0 Revise by KDB248227 D01v02r01 and IEEE1528-2003 Chen Qiang 2015-09-01 Note: The last version will be invalid automatically while the new version is issued. Report No. 2015SAR256 Page 4 / 61 V4.0 CONTENTS: STANDARDS ............................................................................................................................... 2 CONCLUSION ............................................................................................................................. 2 CHANGE HISTORY..................................................................................................................... 3 1. STATEMENT OF COMPLIANCE ......................................................................................... 6 2. ADMINISTRATIVE INFORMATION ........................................................................................ 6 2.1 PROJECT INFORMATION ..................................................................................................................... 6 2.2 TEST LABORATORY INFORMATION ...................................................................................................... 6 2.3 TEST ENVIRONMENT .......................................................................................................................... 6 3. CLIENT INFORMATION .......................................................................................................... 7 3.1 APPLICANT INFORMATION .................................................................................................................. 7 3.2 MANUFACTURER INFORMATION.......................................................................................................... 7 4. EQUIPMENT UNDER TEST (EUT) AND ACCESSORY EQUIPMENT (AE) ......................... 8 4.1 INFORMATION OF EUT ....................................................................................................................... 8 4.2 IDENTIFICATION OF EUT .................................................................................................................... 8 5．OPERATIONAL CONDITIONS DURING TEST .................................................................... 9 5.1 GENERAL DESCRIPTION OF TEST PROCEDURES ................................................................................. 9 5.6 WI-FI TEST CONFIGURATION ............................................................................................................. 9 6. SAR MEASUREMENTS SYSTEM CONFIGURATION ........................................................ 12 6.1 SAR MEASUREMENT SET-UP ........................................................................................................... 12 6.2 DASY5 E-FIELD PROBE SYSTEM .................................................................................................... 13 6.2.1 Es3DV3 Probe Specification ................................................................................................ 13 6.2.2 E-field Probe Calibration ....................................................................................................... 13 6.3 OTHER TEST EQUIPMENT ................................................................................................................ 14 6.3.1 Device Holder for Transmitters ............................................................................................. 14 6.3.2 Phantom ................................................................................................................................. 15 6.4 SCANNING PROCEDURE ................................................................................................................... 15 6.5 DATA STORAGE AND EVALUATION .................................................................................................... 15 6.5.1 Data Storage .......................................................................................................................... 17 6.5.2 Data Evaluation by SEMCAD ............................................................................................... 18 6.6 SYSTEM CHECK ............................................................................................................................... 19 6.7 EQUIVALENT TISSUES ...................................................................................................................... 20 7. SUMMARY OF TEST RESULTS........................................................................................... 21 7.1 CONDUCTED OUTPUT POWER MEASUREMENT .......................................................... 21 7.1.1 SUMMARY .................................................…

Text truncated - open the document above for the full version.

Report No.: BTL-FCCP-1-1505C169 Page 1 of 145 FCC Radio Test Report FCC ID: W3QWIFIHDDP700 This report concerns (check one): Original Grant Class II Change Project No. : 1505C169 Equipment : Portable Wi-Fi HDD Model Name : Wi-Fi HDD/P700 Applicant : Dexxon Groupe Address : 79, Avenue Louis Roche 92230 Gennevilliers Date of Receipt : May 18, 2015 Date of Test : May 18, 2015 ~ May 27, 2015 Issued Date : May 28, 2015 Tested by : BTL Inc. Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) BTL INC. No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, Guangdong, China. TEL: +86-769-8318-3000 FAX: +86-769-8319-6000 Report No.: BTL-FCCP-1-1505C169 Page 2 of 145 Declaration BTL represents to the client that testing i s done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C, or National Institute of Standards and Technology (NIST) of U.S.A. BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. BTL’s report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and BTL-self, extracts from the test report shall not be reproduced except in full with BTL’s authorized written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unl ess the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: BTL-FCCP-1-1505C169 Page 3 of 145 Table of Contents Page 1 . CERTIFICATION 6 2 . SUMMARY OF TEST RESULTS 7 2.1 TEST FACILITY 8 2.2 MEASUREMENT UNCERTAINTY 8 3 . GENERAL INFORMATION 9 3.1 GENERAL DESCRIPTION OF EUT 9 3.2 DESCRIPTION OF TEST MODES 11 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 12 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 13 3.5 DESCRIPTION OF SUPPORT UNITS 13 4 . EMC EMISSION TEST 14 4.1 CONDUCTED EMISSION MEASUREMENT 14 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 14 4.1.2 TEST PROCEDURE 14 4.1.3 DEVIATION FROM TEST STANDARD 14 4.1.4 TEST SETUP 15 4.1.5 EUT OPERATING CONDITIONS 15 4.1.6 EUT TEST CONDITIONS 15 4.1.7 TEST RESULTS 15 4.2 RADIATED EMISSION MEASUREMENT 16 4.2.1 RADIATED EMISSION LIMITS 16 4.2.2 TEST PROCEDURE 17 4.2.3 DEVIATION FROM TEST STANDARD 17 4.2.4 TEST SETUP 18 4.2.5 EUT OPERATING CONDITIONS 19 4.2.6 EUT TEST CONDITIONS 19 4.2.7 TEST RESULTS (9KHZ TO 30MHZ) 19 4.2.8 TEST RESULTS (30MHZ TO 1000 MHZ) 19 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 19 5 . BANDWIDTH TEST 20 5.1 APPLIED PROCEDURES 20 5.1.1 TEST PROCEDURE 20 5.1.2 DEVIATION FROM STANDARD 20 5.1.3 TEST SETUP 20 5.1.4 EUT OPERATION CONDITIONS 20 5.1.5 EUT TEST CONDITIONS 20 5.1.6 TEST RESULTS 20 Report No.: BTL-FCCP-1-1505C169 Page 4 of 145 Table of Contents Page 6 . MAXIMUM PEAK CONDUCTED OUTPUT POWER TEST 21 6.1 APPLIED PROCEDURES / LIMIT 21 6.1.1 TEST PROCEDURE 21 6.1.2 DEVIATION FROM STANDARD 21 6.1.3 TEST SETUP 21 6.1.4 EUT OPERATION CONDITIONS 21 6.1.5 EUT TEST CONDITIONS 21 6.1.6 TEST RESULTS 21 7 . ANTENNA CONDUCTED SPURIOUS EMISSION 22 7.1 APPLIED PROCEDURES / LIMIT 22 7.1.1 TEST PROCEDURE 22 7.1.2 DEVIATION FROM STANDARD 22 7.1.3 TEST SETUP 22 7.1.4 EUT OPERATION CONDITIONS 22 7.1.5 EUT TEST CONDITIONS 22 7.1.6 TEST RESULTS 22 8 . POWER SPECTRAL DENSITY TEST 23 8.1 APPLIED PROCEDURES / LIMIT 23 8.1.1 TEST PROCEDURE 23 8.1.2 DEVIATION FROM STANDARD 23 8.1.3 TEST SETUP 23 8.1.4 EUT OPERATION CONDITIONS 23 8.1.5 EUT TEST CONDITIONS 23 8.1.6 TEST RESULTS 23 9 . MEASUREMENT INSTRUMENTS LIST 24 10 . EUT TEST PHOTO 26 ATTACHMENT A - CONDUCTED EMISSION 30 ATTACHMENT B - RADIATED EMISSION (9KHZ TO 30MHZ) 37 ATTACHMENT C - RADIATED EMISSION (30MHZ TO 1000MHZ) 41 ATTACHMENT D - RADIATED EMISSION (ABOVE 1000MHZ) 60 ATTACHMENT E - BANDWIDTH 109 ATTACHMENT F – MAXIMUM PEAK CONDUCTED OUTPUT POWER 118 ATTACHMENT G - ANTENNA CONDUCTED SPURIOUS EMISSION 120 ATTACHMENT H - POWER SPECTRAL DENSITY 137 Report No.: BTL-FCCP-1-1505C169 Page 5 of 145 REPORT ISSUED HISTORY Issued No. Description Issued Date BTL-FCCP-1-1505C169 Original Issue. May 28, 2015 Report No.: BTL-FCCP-1-1505C169 Page 6 of 145 1. CERTIFICATION Equipment : Portable Wi-Fi HDD Brand Name : EMTEC Model Name : Wi-Fi HDD/P700 Applicant : Dexxon Groupe Manufacturer : Dexxon Groupe Address : 79, Avenue Louis Roche 92230 Gennevilliers Factory : Power7 Technology (Dong Guan) Co., Ltd Address : No.28 Binjiang St.Shishuikou Village, Qiaotou Town, Dongguan City, GuangDong Province P.R.China Date of Test : May 18, 2015 ~ May 27, 2015 Test Sample : ENGINEERING SAMPLE Standard(s) : FCC Part15, Subpart C: 2014 (15.247) / ANSI C63.4-2014 The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. BTL-FCCP-1-1505C169) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of TAF according to the ISO-17025 quality assessment standard and technical standard(s). Report No.: BTL-FCCP-1-1505C169 Page 7 of 145 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standard(s): Applied Standard(s): FCC Part15 (15.247) , Subpart C: 2014 Standard(s) Section Test I…

Text truncated - open the document above for the full version.

Report No. 2015SAR256 Page 1 / 5 V1.0 ANNEX D: Picture of antennas Picture of antennas ANNEX E: Definition of Test Positions POSITION OF BODY TOWARDS PHANTOM WITH 5mm DISTANCE Report No. 2015SAR256 Page 2 / 5 V1.0 POSITION OF BODY TOWARDS GROUND WITH 5mm DISTANCE POSITION OF BODY FRONT 5mm DISTANCE Report No. 2015SAR256 Page 3 / 5 V1.0 POSITION OF BODY BACK 5mm DISTANCE POSITION OF BODY RIGHT SIDE WITH 5mm DISTANCE Report No. 2015SAR256 Page 4 / 5 V1.0 POSITION OF BODY LEFT SIDE WITH 5mm DISTANCE Report No. 2015SAR256 Page 5 / 5 V1.0 ANNEX F: Photograph EUT ------------------------------------------END OF REPORT----------------------------------------------------

Report No. 2015SAR256 Page 1 / 4 V1.0 ANNEX D: Picture of antennas Picture of antennas ANNEX E: Definition of Test Positions POSITION OF BODY TOWARDS PHANTOM WITH 5mm DISTANCE Report No. 2015SAR256 Page 2 / 4 V1.0 POSITION OF BODY TOWARDS GROUND WITH 5mm DISTANCE POSITION OF BODY FRONT 5mm DISTANCE Report No. 2015SAR256 Page 3 / 4 V1.0 POSITION OF BODY RIGHT SIDE WITH 5mm DISTANCE Report No. 2015SAR256 Page 4 / 4 V1.0 ANNEX F: Photograph EUT ------------------------------------------END OF REPORT----------------------------------------------------