W99RL31Relay

Programming Button Motor output 12V Positive input 12V Ground input Negative 12v activation inputs FCC NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. IC NOTE: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. WARNING: CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT

Creative Werks Inc. 1434 East Fleming Ave Des Moines, Iowa 50313 Confidentiality Request Letter Page 1 of 1 Rev 2.0 Jan. 04, 2012 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Permanent Confidentiality Request Confidentiality Request regarding application for certification of FCC ID: W99RL31 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature: Client’s name / title: Joel Fleming / Division Manager Contact information / address: 1434 East Fleming Ave Des Moines, Iowa 50313 TEL: 515-264-8222 FAX: 515-264-8444 E-mail: [email protected]

External Photo

FCC Certification Label FCC ID: W99RL31 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Label Location on EUT EUT View/ FCC ID Label Location

Internal Photo Antenna

FCC PART 15 CLASS B EMI MEASUREMENT AND TEST REPORT For Creative Werks Inc. 1434 East Fleming Ave Des Moines, Iowa 50313 FCC ID: W99RL31 November 27, 2012 This Report Concerns: Original Report Equipment Type: Relay Test Engineer: Eric Li Test Engineer of performing the tests: Adam Yang Report No.: BST12111006Y Receive EUT Date/Test Date: November 20, 2012/ November 20, 2012- November 27, 2012 Reviewed By: Christina Deng Prepared By: Shenzhen BST Technology Co.,Ltd. 3F,Weames Technology Building, No. 10 Kefa Road, Science Park, Nanshan District,Shenzhen,Guangdong,China Tel: 0755-26747751-3 Fax: 0755-26747751-3 ext.826 Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of Creative Werks Inc.This report must not be used by the client to claim product certification, approval,or endorsement by NVLAP, NIST or any agency of the US Government. FCC ID: W99RL31 BST12111006Y Page 2/14 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................... 3 1.1. Report information............................................................................................................ 3 2. PRODUCT DESCRIPTION ...................................................................................................... 4 2.1. EUT Description ............................................................................................................... 4 2.2. Block Diagram of EUT Configuration ............................................................................. 4 2.3. Support Equipment List .................................................................................................... 4 2.4. Test Conditions .................................................................................................................5 3. TEST RESULTS SUMMARY ................................................................................................... 6 4. TEST EQUIPMENT USED ....................................................................................................... 7 5. CONDUCTED EMISSION TEST............................................................................................. 8 5.1. Measurement Uncertainty................................................................................................. 8 5.2. Block Diagram of Test Setup............................................................................................ 8 5.3. Test Standard .................................................................................................................... 8 5.4. Conducted Emission Limit(Class B) ................................................................................ 9 5.5. EUT Configuration on Test .............................................................................................. 9 5.6. Operating Condition of EUT ............................................................................................ 9 5.7. Test Procedure ..................................................................................................................9 5.8. Test Result ........................................................................................................................ 9 6. RADIATED EMISSION MEASUREMENT ......................................................................... 10 6.1. Measurement Uncertainty............................................................................................... 10 6.2. Block Diagram of EUT Configuration ........................................................................... 10 6.3. Test Standard ..................................................................................................................10 6.4. Radiated Emission Limit(Class B) ................................................................................. 11 6.5. EUT Configuration on Test ............................................................................................ 11 6.6. Operating Condition of EUT .......................................................................................... 11 6.7. Test Procedure ................................................................................................................ 12 6.8. Test Result ...................................................................................................................... 12 FCC ID: W99RL31 BST12111006Y Page 3/14 1. GENERAL INFORMATION 1.1. Report information 1.1.1.This report is not a certificate of quality; it only applies to the sample of the specific product/equipment given at the time of its testing. The results are not used to indicate or imply that they are application to the similar items. In addition, such results must not be used to indicate or imply that Creative Werks Inc. approves recommends or endorses the manufacture, supplier or use of such product/equipment, or that Creative Werks Inc. in any way guarantees the later performance of the product/equipment. 1.1.2.The sample/s mentioned in this report is/are supplied by Applicant, Creative Werks Inc. therefore assumes no responsibility for the accuracy of information on the brand name, model number, origin of manufacture or any information supplied. Additional copies of the report are available to the Applicant at an additional fee. No third part can obtain a copy of this report through Creative Werks Inc., unless the applicant has authorized Creative Werks Inc. in writing to do so. Test Facility - The test site used to collect the radiated data is located on the address of Shenzhen Certification Technology Service Co., Ltd (FCC Registered Test Site Number: 197647) on 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2nd Road, Bao'an District, shenzhen 518126, China The Test Site is constructed and calibrated to meet the FCC requirements. FCC ID: W99RL31 BST12111006Y Page 4/14 2. PRO…

Text truncated - open the document above for the full version.

Radiated emissions test