WD6GRG013WLAN IP Print Server Module

GR ‐ G013 WIFI MODULE MANUAL Thanks for your purchase of the WIFI Module. MODULE GR ‐ G013 Microprocessor MediaTek RT5350 SDRAM 16*16 256Mbit 166Mhz Flash Memory 32Mbit Serial Flash 86Mhz Lan Speed 10/100 Mbps Wireless 802.11b/g/n 1T1R Antenna Connector I ‐ PEX connector LED Indicators 1 Power LED,1 WLAN LED,1LAN LED Init/Reset Button 1 Initial Switch Console Port Debug used Operation Temperature 0 °C ~+40 °C Input Voltage/Current 5VDC/1A GR ‐ G013 WIFI MODULE MANUAL WIFI installation guide: 1. Please open the printer’s bottom cover. 2. Find the WIFI module socket of main board. 3. Place this module smoothly like figure 1. 4. Insert this module to the socket, and keep the installation line at the position as figure 2. GR ‐ G013 WIFI MODULE MANUAL FCC Statement: Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limit s for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio co mmunications. However, there is no guarantee that interference will not occur in a particular in stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two co nditions: (1) This device may n ot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~ 11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitt er product procedures. Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without C2P. GR ‐ G013 WIFI MODULE MANUAL IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. 20cm minimum distance has to be able to be maintained between t he antenna and the users for the ho st this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipme nt. GR ‐ G013 WIFI MODULE MANUAL USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be in formed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC r adio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the m anufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then addi tional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subjec t to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: WD6GRG013 ". If the size of th e end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 o f FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer ence and (2) this device must accept any interference received, including interference that may cause undesired operation. Antenna list Ant. Brand Model Name Antenna Type Connector Gain (dBi) 1 TRONTEK TDA ‐ P2FMIPF000 PCB Antenna I ‐ PEX 4.61 2 TRONTEK TAT280 ‐ MRSX000 dipole Antenna I ‐ PEX 2.34

Page No. : 26 Module Approval Request Letter Subject: Module Approval Date: 2014/10/1 FCC ID: WD6GRG013 Dear Reviewer, We, Sporton International Inc., are authorized by Godex International Co., Ltd. to have their state-of-the-art WLAN IP Print Server Module approved under module approval authorization. The application of this module is specified to mobile host equipment. The requirements regulated in CFR47 Part 15.212 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip RT5350F. 3. The requirement of power supply regulation: The part number of the power regulator is G5794. 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 8. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance of MPE RF exposure rule. Please do not hesitate to contact me for any questions of this request letter. Thank you. Company name : Sporton International Inc. Company Address : No.8, Lane 724, Bo-ai St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. Signature : Name : Leo Huang Job Title : Manager

Report No.: 461818-01 SPORTON International Inc. PAGE NUMBER : 1 OF 5 TEL : 886-3-327-3456 ISSUED DATE : Sep. 29, 2014 FAX : 886-3-327-0973 Photographs of EUT Report No.: 461818-01 SPORTON International Inc. PAGE NUMBER : 2 OF 5 TEL : 886-3-327-3456 ISSUED DATE : Sep. 29, 2014 FAX : 886-3-327-0973 Ant. 1 Part Number: TDA-P2FMIPF000 Report No.: 461818-01 SPORTON International Inc. PAGE NUMBER : 3 OF 5 TEL : 886-3-327-3456 ISSUED DATE : Sep. 29, 2014 FAX : 886-3-327-0973 Report No.: 461818-01 SPORTON International Inc. PAGE NUMBER : 4 OF 5 TEL : 886-3-327-3456 ISSUED DATE : Sep. 29, 2014 FAX : 886-3-327-0973 Ant. 2 Part Number: TAT280 Report No.: 461818-01 SPORTON International Inc. PAGE NUMBER : 5 OF 5 TEL : 886-3-327-3456 ISSUED DATE : Sep. 29, 2014 FAX : 886-3-327-0973

Label: Label Here

Report No.: 461818-01 SPORTON International Inc. PAGE NUMBER : 1 OF 3 TEL : 886-3-327-3456 ISSUED DATE : Sep. 29, 2014 FAX : 886-3-327-0973 Photographs of EUT Report No.: 461818-01 SPORTON International Inc. PAGE NUMBER : 2 OF 3 TEL : 886-3-327-3456 ISSUED DATE : Sep. 29, 2014 FAX : 886-3-327-0973 Report No.: 461818-01 SPORTON International Inc. PAGE NUMBER : 3 OF 3 TEL : 886-3-327-3456 ISSUED DATE : Sep. 29, 2014 FAX : 886-3-327-0973

Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : B1 of B3 Appendix B. Maximum Permissible Exposure Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : B2 of B3 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) ＝ d GP30 Power Density: Pd (W/m²) ＝ 377 2 E E ＝ Electric field (V/m) P ＝ Average RF output power (W) G ＝ EUT Antenna numeric gain (numeric) d ＝ Separation distance between radiator and human body (m) The formula can be changed to Pd ＝ 2 377 30 d GP   From the EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : B3 of B3 1.3. Calculated Result and Limit Exposure Environment: General Population / Uncontrolled Exposure For Ant. 1 : Antenna Type : PCB Antenna Conducted Power for IEEE 802.11b: 18.07 dBm Average Output Power Distance (m) Antenna Gain (dBi) Antenna Gain (numeric) (dBm) (mW) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 0.2 4.61 2.8907 18.0700 64.1210 0.036894 1 Complies For Ant. 2: Antenna Type : Dipole Antenna Conducted Power for IEEE 802.11b: 16.46 dBm Average Output Power Distance (m) Antenna Gain (dBi) Antenna Gain (numeric) (dBm) (mW) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 0.2 2.34 1.7140 16.4600 44.2588 0.015099 1 Complies

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Hwa Ya Technology Park, Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw Report Format Version: Rev. 01 FCC RADIO TEST REPORT Applicant’s company GODEX INTERNATIONAL CO., LTD. Applicant Address 13F., No.168, Jiankang Rd., Zhonghe Dist., New Taipei City 235, Taiwan FCC ID WD6GRG013 Manufacturer’s company GODEX INTERNATIONAL CO., LTD. Manufacturer Address 13F., No.168, Jiankang Rd., Zhonghe Dist., New Taipei City 235, Taiwan Product Name WLAN IP Print Server Module Brand Name GoDEX Model No. GR-G013 Test Rule 47 CFR FCC Part 15 Subpart C § 15.247 Test Freq. Range 2400 ~ 2483.5MHz Received Date Aug. 13, 2014 Final Test Date Aug. 29, 2014 Submission Type Original Equipment Statement Test result included in this report is for the IEEE 802.11n and IEEE 802.11b/g of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.10-2013, 47 CFR FCC Part 15 Subpart C, KDB 558074 D01 v03r02 and KDB 662911 D01 v02r01. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report No.: FR461818-01 Report Format Version: Rev. 01 Page No. : i of ii FCC ID: WD6GRG013 Issued Date : Sep. 29, 2014 Table of Contents 1. CERTIFICATE OF COMPLIANCE ......................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT .......................................................................................................................... 2 3. GENERAL INFORMATION .................................................................................................................................. 3 3.1. Product Details....................................................................................................................................................................................3 3.2. Accessories .........................................................................................................................................................................................5 3.3. Table for Filed Antenna.......................................................................................................................................................................6 3.4. Table for Carrier Frequencies .............................................................................................................................................................6 3.5. Table for Test Modes ...........................................................................................................................................................................7 3.6. Table for Testing Locations..................................................................................................................................................................8 3.7. Table for Supporting Units ...................................................................................................................................................................8 3.8. Table for Parameters of Test Software Setting .....................................................................................................................................9 3.9. EUT Operation during Test ...................................................................................................................................................................9 3.10. Duty Cycle ........................................................................................................................................................................................10 3.11. Test Configurations ...........................................................................................................................................................................11 4. TEST RESULT ................................................................................................................................................... 13 4.1. AC Power Line Conducted Emissions Measurement.........................................................................................................................13 4.2. Maximum Conducted Output Power Measurement .........................................................................................................................19 4.3. Power Spectral Density Measurement ..............................................................................................................................................22 4.4. 6dB Spectrum Bandwidth Measurement ..........................................................................................................................................30 4.5. Radiated Emissions Measurement ....................................................................................................................................................37 4.6. Emissions Measurement ....................................................................................................................................................................69 4.7. Antenna Requirements ...................................................................................................................................................................103 5. LIST OF MEASURING EQUIPMENTS ................................................................................................................. 104 6. MEASUREMENT UNCERTAINTY........................................................................................................................ 105 APPENDIX A. TEST PHOTOS .................…

Text truncated - open the document above for the full version.

Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A1 of A15 Appendix A. Test Photos Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A2 of A15 1. Photographs of Conducted Emissions Test Configuration For Ant. 1: FRONT VIEW REAR VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A3 of A15 CLOSE-UP VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A4 of A15 For Ant. 2 : FRONT VIEW REAR VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A5 of A15 CLOSE-UP VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A6 of A15 2. Photographs of Radiated Emissions Test Configuration For Ant. 1: Test Configuration: 9kHz ~30MHz FRONT VIEW REAR VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A7 of A15 Test Configuration: 30MHz~1GHz FRONT VIEW REAR VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A8 of A15 CLOSE-UP VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A9 of A15 Test Configuration: Above 1GHz FRONT VIEW REAR VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A10 of A15 CLOSE-UP VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A11 of A15 For Ant. 2 : Test Configuration: 9kHz ~30MHz FRONT VIEW REAR VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A12 of A15 Test Configuration: 30MHz~1GHz FRONT VIEW REAR VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A13 of A15 CLOSE-UP VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A14 of A15 Test Configuration: Above 1GHz FRONT VIEW REAR VIEW Report No.: FR461818-01 FCC ID: WD6GRG013 Page No. : A15 of A15 CLOSE-UP VIEW