WGO918F-08kiosk with RFID

IER 918F KIOSK N0F352A1 – Rev. 1 May 20, 2011 INSTALLATION GUIDE N0F352A1 IER 918F Installation Guide Page 2 N0F352A1 – Rev. 1 May 20, 2011 Ce document est la propriété d'IER et ne doit pas être reproduit ou communiqué sans autorisation écrite This document is the property of IER and may not be reproduced or communicated without prior written authorization IER SIEGE - HEADQUARTERS IER S.A. 3, rue Salomon de Rothschild 92156 SURESNES CEDEX France Tel. +33 (0)1 41 38 60 00 Fax +33 (0)1 41 38 62 75 IER DANS LE MONDE - IER WORLDWIDE CHINA IER Shanghai Kuen Yang Plaza #1101 798 Zhao Jia Bang Road SHANGHAI 200030 P.R.C. Phone: +86 (21) 6473 6792 Fax: +86 (21) 6473 6806 GERMANY IER GmbH Wilhelm-Heinichen-Ring 4 29227 CELLE Phone: +49 (0) 5141/980 89 14 Fax: +49 (0) 5141/980 89 20 SINGAPORE IER PTE Ltd 120 Lower Delta Road #14-13/16 Cendex Centre SINGAPORE 169208 Phone: +65 6276 6966 Fax: +65 6271 5563 UNITED STATES IER Inc. Addison 16415 Addison Road Suite 160 ADDISON, TEXAS, TX 75001 Phone: +1 (972) 991 2292 Fax: +1 (972) 991 1044 Toll free: 1-800 624 8538 IER Inc. Belton 1000 Industrial Park Road BELTON, TX 76513 Phone: +1 (254) 933 5000 Fax: +1 (254) 933 5050 SPAIN IER Impresoras Especializadas, S.L. C/ Torre de Don Miguel, 23 E-28031 – MADRID Phone: +34 91 535 89 75 Fax: +34 91 535 89 76 IER 918F Installation Guide Ce document est la propriété d'IER et ne doit pas être reproduit ou communiqué sans autorisation écrite This document is the property of IER and may not be reproduced or communicated without prior written authorization Page 3 N0F352A1 – Rev. 1 May 20, 2011 NOTICE WARNING THIS IER PRODUCT COMES WITH SEALED LEAD ACID BATTERIES (UPS) AND A LITHIUM BATTERY (MAIN PCB). ANY KIND OF OPERATIONS ON THESE ELEMENTS MUST EXCLUSIVELY BE CARRIED OUT BY MAINTENANCE PERSONNEL QUALIFIED BY IER. MOREOVER, THESE BATTERIES MAY ONLY BE REPLACED BY IER APPROVED MODELS. WARNING DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS. The United States Federal Communications Commission (in 47 CFR 15.105) has specified that the following notice be brought to the attention of users of this product. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna  Increase the separation between the equipment and receiver  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected  Consult the dealer or an experienced radio/TV technician for help. In accordance with FCC requirements, changes or modifications not expressly approved by IER could void the user's authority to operate this product. Use of a shielded cable is required to comply within Class B limits of Part 15 of FCC Rules. The AC line power connector must at all times be accessible, as it serves as the disconnecting device. WARNING THIS APPLIANCE MUST BE GROUNDED. THIS PRODUCT MUST EXCLUSIVELY BE CONNECTED TO AN ELECTRICAL CIRCUIT THAT IS:  PROVIDED WITH A GROUND FAULT CIRCUIT INTERRUPTER (GFCI) COMPLYING WITH IEC 364 AND NFC15-100 REGULATIONS, AND  CONFORMING WITH THE VOLTAGE CHARACTERISTICS SPECIFIED BY THE NF EN 50160 STANDARD. The cover(s), door(s) and/or drawer(s) of this product is (are) intended for occasional use and must be normally closed. This document contains proprietary information of IER. It may not be reproduced or communicated without prior written authorization of IER. It is intended solely for the use of the product described herein, to the exclusion of any other usage. It is provided as is, for information purposes only, without any warranty of any kind, including any warranty of fitness or a particular purpose, and may be modified by IER at any time. The warranty shall be null and void in case of use of any spare part, special tool or consumable not expressly approved in writing by IER and in the event of attempted repair or servicing of the machines by persons lacking the requisite technical qualifications. IER 918F Installation Guide Page 4 N0F352A1 – Rev. 1 May 20, 2011 Ce document est la propriété d'IER et ne doit pas être reproduit ou communiqué sans autorisation écrite This document is the property of IER and may not be reproduced or communicated without prior written authorization NORWAY – SWEDEN – FINLAND: Apparaten skall anslutas till jordat uttag när den ansluts till ett nätverk. The equipment complies with R&TTE directive 1999/5/EC of the European Parliament and of the council of 9 March 1999. The equipment may be fitted with RFID contactless readers working in the frequency band 13.553-13.567MHz for inductive application. The equipment may be fitted with RFID UHF reader working in the frequency band 869.4-869.65MHz for non specific short range device. The comprehensive EC declaration of conformity is available on request from IER Quality Department. In compliance with the European Directive 2002/96/CE relative to the management of Waste Electrical and Electronic Equipment (WEEE) implemented as of August 13, 2005, this product may not be disposed of with regular household waste. All products concerned by this directive are marked with the above symbol. The e…

Text truncated - open the document above for the full version.

GYL Technologies 21 rue de la Fuye Parc d’Activité de Lanserre 49610 JUIGNE SUR LOIRE Tel : 02 41 57 57 40 – Fax : 02 41 45 25 77 18 th April 2012 Equipment Authorization Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: WGO918F-08 Product Name: IER918F Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential:  Block diagram  Schematics and parts list  operational description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. For IER 3 Rue Salomon de Rothschild BP 320 92156 SURESNES Cédex FRANCE By Olivier ROY, technical manager of Gyl Technologies as authorized agent of IER Tel.: (33)241575740

IER Mr. SEHB Rachid 3 rue Salomon de Rothschild, BP320 F-92156 Suresnes Cedex France Parkring 1 A-8074 Grambach bei Graz Austria/Europe Tel: +43 (0)316-403125 +43 (0)664-4048012 [email protected] UID: ATU63971189 FBN : 305712 b Graz, 28.11.2011 Control over final installation FCC ID ZKCPP-0403-3003 Manufacturer/ responsible person: Kronegger GmbH. Thomas Feibel Parkring 1, 8074 Grambach/Graz, Austria declares that the product: Product description: Kronegger NFC P&P Reader FCC ID ZKCPP-0403-3003 used by Integrator/ responsible person: IER Mr. SEHB Rachid 3 rue Salomon de Rothschild, BP320 F-92156 Suresnes Cedex France is integrated according to our specification and fulfilling the limitation on the final installation. Signature: Thomas Feibel

EQUIPMENT FCC ID : WGO918F-08 Exhibit 3 EXTERNAL PHOTOS Page : 1/2 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a 1.2 PRODUCT PICTURES: Front view EQUIPMENT FCC ID : WGO918F-08 Exhibit 3 EXTERNAL PHOTOS Page : 2/2 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Rear view

IER 918F N0F8SEA1 Localisation of label for IER 918F

EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 1/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a 1.2 DETAILS: Hengstler GPP Printe r Printer IER 400 UPS Passport reader RTE 8000 HS Screen part U.C. CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 2/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Omrom Card reader HHP barcode reader CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 3/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Rear internal wiring CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 4/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Passport reader RTE 8000 HS (with new FCC ID label) Label is visible at installation or when reloaded printers with paper. CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 5/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Hengstler GPP Printer CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 6/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a UPS U.C. CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 7/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Kroeneger RFID Reader (FCC ID: ZKCPP-0403-3003) was not labeled for the test. CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 8/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a IER 400 printer Antenna position in the printer: CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 9/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Printer main board: front view Printer Main board: rear view CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 10/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Link board: front view Link board: rear view CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 11/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Radio part Radio board: front view Radio board: rear view CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 12/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Antenna CONFIDENTIAL EQUIPMENT FCC ID : WGO918F-08 Exhibit 9 INTERNAL PHOTOS Page : 13/13 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a Printer Power supply CONFIDENTIAL

The reproduction of this document is authorised only if integral. Any partial reproduction must be authorised by GYL Technologies. This document result of test applied on one sample. It doesn’t prejudge of conformity of all products to the tested sample. GYL technologies Parc d’activités de Lanserre 21 rue de la Fuye 49610 JUIGNE SUR LOIRE FRANCE Tel. : +33 (0) 2.41.57.57.40 Fax : +33 (0) 2.41.45.25.77 TEST REPORT According to FCC, CFR 47 Part 15 IER 918 F N°060158-CC-1-c FCC CERTIFICATION TEST REPORT EQUIPMENT FCC ID : WGO918F-08 The 21 pages of this report are not sharable 2 Identification : 060158-CC-1-c FCC registration # 90469 Summary 1 REFERENCE AND RECORD OF REVISIONS OF THE TEST REPORT: .......................................................4 2 INTERPRETATION AND REMARKS: ..................................................................................................................4 2.1 RESULTS: .................................................................................................................................................................................... 4 3 GENERAL INFORMATION: ...................................................................................................................................5 3.1 APPLICANT: ................................................................................................................................................................................ 5 3.2 MANUFACTURER: ..................................................................................................................................................................... 5 3.3 TEST DATE: ................................................................................................................................................................................ 5 3.4 TEST SITE: ................................................................................................................................................................................... 5 4 INTRODUCTION: .....................................................................................................................................................5 5 MEASUREMENT EQUIPMENT LIST: ..................................................................................................................6 6 EXERCISING TEST CONDITIONS: ......................................................................................................................8 7 CONFORMANCE STATEMENT: ...........................................................................................................................8 7.1 STANDARDS REFERENCED FOR THIS REPORT: ................................................................................................................. 8 7.2 JUSTIFICATION: ......................................................................................................................................................................... 8 8 TEST ACCORDING TO CFR 47 PART 15.............................................................................................................9 8.1 REFERENCE DOCUMENTATION: ........................................................................................................................................... 9 8.2 POWER LINE CONDUCTED EMISSIONS MEASUREMENTS (15.207): ............................................................................... 9 8.3 RESULTS: .................................................................................................................................................................................... 9 8.4 INTERPRETATION AND REMARKS: ..................................................................................................................................... 11 8.5 Intentional radiator operation within the band 902 – 928 MHz §15.249: ................................................................................... 12 8.6 Receiver spurious radiation ......................................................................................................................................................... 21 8.7 Antenna requirements ................................................................................................................................................................. 21 FCC CERTIFICATION TEST REPORT EQUIPMENT FCC ID : WGO918F-08 The 21 pages of this report are not sharable 3 Identification : 060158-CC-1-c FCC registration # 90469 OTHER ASSOCIATED FILES: 060158 Exhibit 1 ID label WGO918F-08 060158 Exhibit 1b label localisation WGO918F-08 060158 Exhibit 3 External Photographs WGO918F-08 060158 Exhibit 4 Block diagram WGO918F-08 060158 Exhibit 5 Schematics of RF WGO918F-08 060158 Exhibit 7 Test set up photos WGO918F-08 060158 Exhibit 8 installation manual WGO918F-08 060158 Exhibit 8a notice warning statement WGO918F-08 060158 Exhibit 9 Internal Photographs WGO918F-08 GRANT ZKCPP-0403-3003 (RFID 13.56MHz) DGFSSDRTE8000 TCB GrantForm (Passport reader 13.56MHz) 060158 Exhibit 12 Operational description WGO918F-08 060158 Exhibit 13 cover letter FCC ID WGO918F-08 FCC CERTIFICATION TEST REPORT EQUIPMENT FCC ID : WGO918F-08 The 21 pages of this report are not sharable 4 Identification : 060158-CC-1-c FCC registration # 90469 1 Reference and record of revisions of the test report: Test report number : Revision : Number of pages Modification reasons : 060158-CC-1-a a 24 Creation, July 28, 2011 060158-CC-1-b b 18 change to part 15.249, with new spurious measurement, 4 April 2012 060158-CC-1-c c 21 Band edge re measurement Redactor : O.ROY Date of writing : 10 Mai 2012 Technical control: O. ROY Quality Control: F. NOURRY 2 Interpretation and remarks: 2.1 RESULTS: This equipment complies with the rules of the FCC section 15.249 and related sections concerning its radio functions. This equipment complies with the rules of the FCC section 15.207, 15.209 and related sections concerning its intentional r…

Text truncated - open the document above for the full version.

EQUIPMENT FCC ID : WGO918F-08 Exhibit 7 TEST SET UP PHOTOS Page : 1/2 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a RADIATED FIELD TEST SET UP Antenna in front of the back of equipment with turntable at 0° EQUIPMENT FCC ID : WGO918F-08 Exhibit 7 TEST SET UP PHOTOS Page : 2/2 Written by : O. ROY 10 November 2011 Test report # : 060158-CC-1-a CONDUCTED TEST SET UP