WNU-BPDTBOOK PORT DT

This document describes the mai n functions which are used in the "advanced mode". Change to the advanced mode as follows. Turn off the player at first. Then turn on th e player with the number 5 key being pressed until the player annou nces "advanced mode". (To change to the simple mode, do the same until the player announces " simple mode".) 1. Connecting Book Port DT to mains outlet Insert the small round plug on the end of AC adaptor into back of the unit (1). Ens ure the supplied power cable is connected to the AC adaptor firmly befo re plugging mains plug into a mains outlet. 2. Power On/Off, se tting sleep timer Press and hold the Power On/Off button (2). Press the sleep timer key (3) until you reach the desired setting. 3. Inserting p layback media Disc; Insert the cardrige into the NLS cardrige slot (4) at front of the unit until the disc will be autom atically taken into the unit. SD card; Insert the SD card into th e SD card slot (5) on the left side of the unit. USB memory; Insert the the NLS cardrige slot (4) at front of the unit. 4. Removing playback media SD card; Push th e SD card inwards, then the card shou ld pop out. NLS cardrige; Pull out the NLS cardrige from NLS cardrige slot (4) at front of the unit.USB memory; Same use NLS cardrige slot (4). 5. Playback and stop To start playback, press the Play/stop key (8). To stop playback, press the Play/stop key (8) again. 6. Adjusting volume, speed and tone Volume; Press the Volume up key (9 ) to increase, press the Volume down key (10) to decrease. Speed; Press the Speed up key (1 1) to increase, press the Speed down key (12) to decrease. Tone; Press the Tone up key (1 3) to increase, press the Tone down key (14) to decrease. 7. Rewinding / Fast forward Press and hold the Rewind ke y (15) to fast rewind. Press and hold the Fast Forward key (16) to fast forward. 8. Selecting media and title Press and hold the Previous title key (17) or Next title key (18) repeatedly, or press the Previous title key (17) and Nexttitle key (18) at the same time repeate dly until you reach the desired media. Then press the Previous tit le key (17) or Next title key (18) to select the title. 9. Moving by Level Press the Number 2 key (19) or 8 key (20) to select the navigation level, then press the Number 4 key (21) to move backward or the Number 6 key (22) to move forward within the required level. 10. Direct jump to page/heading Page; Press the GoTo key (23) once and input the page number with the number key, then press the Enter key (24) to go to page. Heading; Press the GoTo key (23) twice and input the heading number with the number key, then press the Enter key (24) to go to heading. 11. Direct jump to bookma rk / Adding bookmark Press the Bookmark key (25) once and input the bookmark number with the number key, then press the Enter key (24) to go to bookmark. Press the Bookmark key (25) twice at the desired position and input the bookmark number with the number key, then press the Enter key (24) to add bookmark. 12. Selecting menu Press the Menu key (26), a nd press the Number 4 key (21) or 6 key (22) to select th e menu, then press th e Enter key (24) to confirm or the Cancel key (27) to cancel. 13. Getting book information Press the Information key (28) or press and hold the Play/stop key (8) to get the book information. 14. Backing up title Select the title you want to back up at first. Press the Number 9 key (29) to access the back up fe ature, and press the Number 4 key (21) or 6 key (22) to select the target media, then press the Enter key (24) to confirm. Plextalk will ask you that you wish to proceed or not. Press the Enter key (24) again to proceed or the Cancel key (27) to abort. Wired LAN (1) DC input (4) NLS cardrige slot Mic hole &Microphone jack Head phone jack (5) SD card slot (22) (29) (9) (10) (26) (11) (3) (2) (7) (17) (24) (16) (8) (28) (15) (27) (25) (20) (23) (21) (13) (12) (14) (19) (18) Quick Start explains – Book Port DT – Book Port DT Quick Start FCC Notice to User This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help

Date: May 8, 2012 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern: The Shinano Kenshi Co., Ltd., the undersigned, hereby authorizes Mr.Wu Xuewen from Shenzhen Morlab Communications Technology Co., Ltd., to act on the behalf of the Shinano Kenshi Co., Ltd.. solely in matters relating to the application for an FCC equipment authorization for FCC ID # WNU-BPDT including the signing of documents in connection with this Application. Necessary acts carried out by Shinano Kenshi Co., Ltd. on our behalf of the Shinano Kenshi Co., Ltd. in connection with the Application shall have the same effect as acts of the Shinano Kenshi Co., Ltd. The Shinano Kenshi Co., Ltd. also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Thank you for your attention to this matter. Yours Sincerely,

External Photos

FCC ID: WNU-BPDT Label Label Location

Internal Photos

Report No.: SZ11100015E01 Page 2 of 13 TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................... 3 1.1 EUT Description ......................................................................................................................... 3 1.2 Test Standards and Results ........................................................................................................ 4 1.3 Facilities and Accreditations ...................................................................................................... 5 1.3.1 Facilities .................................................................................................................................... 5 1.3.2 Test Environment Conditions .................................................................................................... 5 1.3.3 Measurement Uncertainty ......................................................................................................... 5 2. TEST CONDITIONS SETTING............................................................................................... 6 2.1 Test Mode .................................................................................................................................... 6 2.2 Test Setup and Equipments List ................................................................................................ 7 2.2.1 Conducted Emission.................................................................................................................. 7 2.2.2 Radiated Emission ..................................................................................................................... 8 3. 47 CFR PART 15B REQUIREMENTS .................................................................................... 9 3.1 Conducted Emission ................................................................................................................... 9 3.1.1 Requirement .............................................................................................................................. 9 3.1.2 Test Description ........................................................................................................................ 9 3.1.3 Test Result ................................................................................................................................. 9 3.2 Radiated Emission .................................................................................................................... 11 3.2.1 Requirement ............................................................................................................................ 11 3.2.2 Test Description ...................................................................................................................... 11 3.2.3 Test Result ............................................................................................................................... 11 Change History Issue Date Reason for change 1.0 May 10, 2012 First edition Report No.: SZ11100015E01 Page 3 of 13 1. GENERAL INFORMATION 1.1 EUT Description EUT Type ........................Book Port DT Serial No. ........................(n.a., marked #1 by test site) Hardware Version .......... .PP Software Version ............. Applicant ......................... Manufacturer .................. . PP Shinano Kenshi Co., Ltd. 1078, Kami-Maruko, Ueda-Shi, Nagano-Ken, 386-0498, Japan GROUP SENSE (International) Ltd 6th Floor, Building 9, No.5 Science Park West Avenue, Hong Kong Science Park, Shatin, New Territories, Hong Kong Modulation Type ............ .FHSS, DSSS Power supply ..................Battery Brand Name: HUANYU Model No.: 6XHYMPAA1800N Serial No.: (n.a. marked #1 by test site) Capacitance: 1800mAh Rated Voltage: 7.2V Ancillary Equipment 1 ... .AC Adapter (Charger for Battery) Brand Name: Ten Pao Model No.: S024EM1200200 Serial No.: (n.a. marked #1 by test site) Rated Input: 100-240V, 600mA, 50/60Hz Rated Output: 12V, 2000mA NOTE: 1. The EUT is a DAISY Book Playback, it supports 2.4G Bluetooth and 2.4G WIFI bands, and it supports USB and SD Card play, it has a RJ45 port which can connected with the PC. 2. For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Report No.: SZ11100015E01 Page 4 of 13 1.2 Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart B: No. Identity Document Title 1 47 CFR Part 15 (10-1-09 Edition) Radio Frequency Devices Test detailed items/section required by FCC and IC rules and results are as below: No. Section Description Result 1 15.109 Radiated Emission PASS 2 15.107 Conducted Emission PASS NOTE: The tests were performed according to the method of measurements prescribed in ANSI C63.4 2009. Report No.: SZ11100015E01 Page 5 of 13 1.3 Facilities and Accreditations 1.3.1 Facilities Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L3572. All measurement facilities used to collect the measurement data are located at 3/F, Electronic Testing Building, Shahe Road, Xili, Nanshan District, Shenzhen, 518055 P. R. China. The test site is constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22; the FCC registration number is 741109. 1.3.2 Test Environment Conditions During the measurement, the environmental conditions were within the listed ranges: Temperature (°C): 15 - 35 Relative Humidity (%): 30 - 60 Atmospheric Pressure (kPa): 86 - 106 1.3.3 Measurement Uncertainty The uncertainty is calculated using the methods suggested in the "Guide to the Expression of Uncertainty in Measurement" (GUM) published by ISO. Uncertainty of Conducted Emission: ±…

Text truncated - open the document above for the full version.

Test Setup Photos 1. CE 2．RE