WO9-PIR-SDPIR MOTION SENSOR WITH HIDDEN CAMERA, SD RECORDER

PIR-SD User’s Manual PIR Motion Sensor with Hidden Color Camera, SD Recorder, and Remote Control © Copyright 2012 This manual is furnished under license and may be used or copied only in accordance with the terms of such license. E xcept as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or any means, electronic, mechanical, recording, or otherwise, including translation to another language or format, without the prior written permission of SecurityMan. The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by SecurityMan. SecurityMan Inc assumes no responsibility or liability for any errors or inaccuracies that may appear in this book. FCC Information Notes on FCC’s “Consistent Statement of Information” This product meet the requirements specified in Part 15 of FCC Regulation. Operation rests with the following two conditions: (1) The equipment should not cause any harmful interference. (2) The equipment must receive and process any interference, including any possible interference caused by operation mistakes. After testing the product, we confirm that the camera complies with the provision for class C digital equipment in the 15th part in FCC regulations; and the receiver complies with the limitations for class B digital equipment in Part 15 of FCC regulation. The product generates, applies and emits radio waves. It might cause harmful interferences to wireless communication if not be installed and used following the description of the manual. The product may cause interference in residential area, and the customer should take remedies to eliminate the interference on their own costs. If the product causes any harmful interference to wireless equipment or disturbs the receiving of TV signals (it can be identified by turning on and off the product), you can solve the trouble by following methods: • Readjust the product or put it in another place. • Extend the distance between the equipment interfered and the product. • Refer to dealers or experienced radio electrician for help. Warranty SecurityMan warrants that this product will be free from defects in title, materials and manufacturing workmanship for one year from the date of the purchase or otherwise specified on the package. If the product is found to be defective then, as your sole remedy and as the manufacturer’s only obligation, SecurityMan will repair or replace the product. This warranty is exclusive and is limited to this product. This warranty shall not apply to products that have been subjected to abuse, misuse, abnormal electrical or environmental conditions, or any condition other than what can be considered normal use. Warranty Disclaimers SecurityMan Inc, makes no other warranties, express, implied or otherwise, regarding this product, and specifically disclaims any warranty for merchantability or fitness for a particular purpose. The exclusion of implied warranties is not permitted in some states and the exclusions specified herein may not apply to you. This warranty provides you with specific legal rights. There may be other rights that you have which vary from state to state. Limitation of Liability The liability of SecurityMan Inc, arising from this warranty and sale shall be limited to a refund of the purchase price. In no event shall SecurityMan be liable for costs of procurement of substitute products or services, or for any lost profits, or for any consequential, incidental, direct or indirect damages, however caused and on any theory of liability, arising from this warranty and sale. These limitations shall apply not withstanding any failure of essential purpose of any limited remedy. For Tech Support Call: 8 8 8 -977-3777 SecurityMan 4601 E. Airport Drive, Ontario, CA, 91761, USA Te l : 909-230-6668 Fax: 909-230-6889 Email: [email protected] Website: www.securitymaninc.com Copyright 2012 by SecurityMan v1.0 Table of Contents Introduction 1 Features 1 Important 2 Operating Restrictions 2 Conditions 5 Safety Instructions 5 Package Contents 6 Product Basics 7 PIR-SD 7 Remote Control 7 Set Up 8 Set the Date and Time 8 Adding and Cancelling Remote Control 12 Adding Remote Control 12 Cancelling Remote Control 12 Operation 13 Using PIR-SD 13 Motion Detection Recording 13 Emergency Recording 13 Stop Recording 14 New File Alert 14 SD Full Alert (Memory Full) 14 Playback Recorded Video 15 Integrating with Air-Alarm Series 15 Adding PIR-SD Remote to the Alarm Host 16 Cancelling PIR-SD Remote from the Alarm Host 16 Adding PIR-SD Motion Detection to the Alarm Host 16 Cancelling PIR-SD Motion Detection from the Alarm Host 16 Enabling Video Recording 17 Disabling Video Recording 18 Specifications 19 1 Introduction Thank you for purchasing SecurityMan PIR-SD. The PIR-SD is a color camera with SD recorder hidden inside a PIR motion detector. This covert motion detector camera blends perfectly into almost any home or business environment where an alarm system might be present and can also be intergraded with any of our SecurityMan DIY Wireless Home Alarm Systems, providing you with both security and discreet monitoring capabilities. So whether you’re looking to expand your wireless security system or just looking for a covert hidden camera, the PIR-SD will fit your needs. Features • PIR motion sensor with color camera and SD recorder (SD card not included) • Works independently or can be integrated with any SecurityMan Air-Alarm series wireless alarm systems • Up to 300ft (clear line of sight) wireless transmitting distance between the PIR-SD and alarm host (100ft indoors) • 1-minute video clip per motion detection event • Records up to 12 hours of video footage on a 32 GB SD card • SD card full notification • Audible and visual new file alert notification • Can easily be armed/disarmed via remote control, alarm host keypad, or phone call (when i…

Text truncated - open the document above for the full version.

PIR-SD According to the control center sends instruction, operational video stop video, etc AK3751B Receive signal PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn Control Center 433.52MHz Receive signal infrared detector AK3751B_BGA100

PIR-SD According to the control center sends instruction, operational video stop video, etc AK3751B Receive signal PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn Control Center 433MHz Receive signal infrared detector AK3751B_BGA100

SHENZHEN XI LONG ELECTRONICS CO., LTD FCC ID: WO9- PIR-SD POWER OF ATTORNEY May 8, 2013 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Bontek Compliance Testing Laboratory Ltd.(Tony Wu) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Bontek Compliance Testing Laboratory Ltd. (Tony Wu) on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act.We, SHENZHEN XI LONG ELECTRONICS CO., LTDare not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuantto that section. Sincerely, SHENZHEN XI LONG ELECTRONICS CO., LTD Mary Zhong (Sales Manger)

深圳市华标检测技术服务有限公司 Bontek Compliance Testing Laboratory Co., Ltd DATE: May 2, 2013 Dear TCB Testing Section of Timco Engineering, Inc., Thank you for cooperation. I would like to submit the a new Notified Body application of SHENZHEN XI LONG ELECTRONICS CO., LTD/ PIR motion sensor with hidden camera,SD recorder ( Model: PIR-SD) by your TCF Certificated today. Best Regards, Bontek Compliance Testing Laboratory Co., Ltd. Tony Wu/General Manager

External Photographs EUT –The Whole View (appearance one) EUT –Front View EUT – Rear View EUT – Side View EUT –Front View (appearance two) EUT – Rear View EUT – Adapter View

FCC ID Label Sample for FCC ID: WO9- PIR-SD SHENZHEN XI LONG ELECTRONICS CO., LTD Model: PIR-SD FCC ID: WO9- PIR-SD FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for ANY interference, for example RADIO or TV interference, caused by unauthorized modifications to this equipment. Such modifications could void the user’ authority to operate the equipment.

FCC ID Location FCC ID Location

Internal Photographs EUT - Open View EUT - PCB Top View ANTENNA EUT - PCB Rear View EUT - PCB View EUT - PCB View

PIR-SD OPERATION PRINCIPLE Basic operation principle： When sensor A & B detect body intrusion signal by Lens A & B, they will send signal to CPU processor to analyze the frequency, range and fluctuating fringe data after processing by each amplifying and filtering circuit. And make relevant estimation according to software setting, and lots of signal parameters of home pets are lead into memorizer for analysis and usage. If detected 2-way alarm signal is in accordance with setting requirement, alarm condition can be produced, CPU will input a signal to drive 433.92M transmission module and send wireless signal to control panel.

TX6477-0214-V4.sch-2 - Tue Feb 14 17:09:27 2012 SD卡数据线 R101 22K D100 RB521S MEMORY BUS GPIO,PWM Camara,SPI,I2S,UART ANYKA AK3751B_BGA100 K6 RTC_WU_WD A5 #DRAM_WE B6 #DRAM_RAS G7 DRAM_DM[1] G6 DRAM_DM[0] F3 MDATA[9] E6 MDATA[8] E3 MDATA[7] E2 MDATA[6] D2 MDATA[5] C2 MDATA[4] A1 MDATA[3] A3 MDATA[2] H6 MDATA[15] F7 MDATA[14] F6 MDATA[13] G4 MDATA[12] G2 MDATA[11] E1 MDATA[10] B4 MDATA[1] B5 MDATA[0] C4 #DRAM_CS D1 DRAM_CLK H5 DRAM_CKE A6 #DRAM_CAS C3 DRAM_BANK1 B1 DRAM_BANK0 F4 MADDR[9] E5 MADDR[8] E4 MADDR[7] F2 MADDR[6] D3 MADDR[5] C1 MADDR[4] B2 MADDR[3] A2 MADDR[2] G5 MADDR[12]/GPIO46_PD G3 MADDR[11]/GPIO45_PD F5 MADDR[10] B3 MADDR[1] A4 MADDR[0] H8 #RST F9 UART_TXD/GPIO3_PU F8 UART_RXD/GPIO4_PU C9 SPI_DIN B10 MMC_D7/SDIO_D3/GPIO11_PU C10 MMC_D6/SDIO_D2/GPIO10_PU A7 MMC_D5/SDIO_D1/GPIO9_PU D8 MMC_D4/SDIO_D0/GPIO8_PU B9 SPI_DOUT/GPIO14_PU G8 SDIO_MCK/GPIO13_PU A10 SPI_CLK/GPIO15_PU B7 MMC_MCMD/SDIO_MCMD/GPIO6_PU C8 #SPI_CS/GPIO40_PD J1 VIVREF/GPIO22_PD H3 VISCLK/GPIO39_PD J4 VIPCLK/GPIO38_PD K2 VIHREF/GPIO23_PD J3 VI_D7/GPIO37_PD H2 VI_D6/GPIO36_PD F1 VI_D5/GPIO35_PD G1 VI_D4/GPIO34 J2 VI_D3/GPIO33 H1 VI_D2/GPIO32 K3 VI_D1/GPIO31 K1 VI_D0/GPIO30 K4 DGPIO[0]/GPIO47_PD U1-A AK3751B_BGA100 C101 1uF 12 D10 RB521S R101K VDD33 SDRAM_CS SDRAM_RAS SDRAM_WR SDRAMCLK+ SDRAMCKE BA0 BA1 UART2_TXD UART2_RXD SDRAM_CAS MBE1 MBE0 CIS_VIPCLK CIS_VIHREF CIS_VISCLK CIS_VIVREF SDIO_CMD SDIO_MCK POWER_OFF SPI_CS SPI_DIN SPI_DOUT SPI_CLK CIS_VIPIXEL7 CIS_VIPIXEL6 CIS_VIPIXEL5 SPI_CS SPI_DIN SPI_CLK CIS_VIPIXEL4 CIS_VIPIXEL3 CIS_VIPIXEL2 CIS_VIPIXEL1 CIS_VIPIXEL0 SPI_DOUT A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 RESET RESET SDIO_D0 SDIO_D1 SDIO_D2 SDIO_D3 USB_BOOT A[0:11] SDIO_CD USB_5V TX6477-0214-V4.sch-3 - Tue Feb 14 17:09:28 2012 1.5V 3.0V C169/C170紧挨着E8 脚放置； C177/C178紧挨着D4 脚放置； C173/C174紧挨着B8 脚放置； C175/C176紧挨着D5 脚放置； C183/C184紧挨着D6 脚放置； C167/C168紧挨着C5 脚放置； LayOut时电容尽量紧挨所对应PIN脚 C171/C180紧挨着K10 脚放置； C107/C108紧挨着E10 脚放置； 默认为AVCC3V3供电， 也就是模拟电源供电。 C174 4.7uF + C163 10uF C183 100nF C175 100nF + C168 10uF R144220K + C177 10uF C15422pF + C117 22uF C116 100nF C114 18pF R1251M C118 100nF C113 18pF CLOCK/PLL POWER PMU AUDIO/ADC USB_OTG ANYKA AK3751B_BGA100 J5 XTAL32KO K5 XTAL32KI D9 XTAL12MO D10 XTAL12MI J10 VMID_VCM2 K9 VDDMIC_VCM3 E10 VDDA/VDD(PLL) F10 OTG_RREF G10 OTG_DP G9 OTG_DM K8 MICP J7 HPR K7 HPL J6 AVSS(AUDIO) H7 AVDD33(AUDIO) H9 VSS(USB) J8 RTC_BAT_IN_AD4 J9 AIN_AD5 C7 VSS2 H4 VSS4 D7 VSS3 E9 VSS(PLL) C6 VSS1 K10 VREF_1V5 E7 VIN_LDO33 A9 VIN_BK_LDO12 D4 VDDIO3 C5 VDDIO1 D6 VDD3 D5 VDD1 A8 SW12 E8 LDO33_OUT/VDDIO B8 LDO12_OUT H10 VCC(USB) U1-B AK3751B_BGA100 + C156 4.7uF C166 100nF C171 100nF C169 100nF C167 100nF R113 NC/0R + C176 22uF + C184 10uF R123 10M R105 10K C107 100nF D102 IN5819 L101 10uH C164 100nF C162 100nF + C165 22uF C153 22pF C170 4.7uF C155 100nF C180 22uF C108 1uF C173 100nF C9 1uF C1 100nF 12 Y1 12MHz 1 2 Y2 32.768KHz R230R R19NC/0R POWRDET VREF_1V5 VBAT VDD1V2 VDD1V2 VDD33 VDD33 VBAT AVDD33 VCM3 USBDP VCM2 VCM3 MIC_P USBDM VCM2 AVDD33 VDD1V2 GND VREF_1V5 VDD1V2 VDD1V2 VDD1V2 VDD33 VDD33 12MI 12MO 32KI 32KO 32KO 32KI 12MO 12MI GND GND GND POWER_KEY GND GND VBAT LI_4.2V TX6477-0214-V4.sch-4 - Tue Feb 14 17:09:28 2012 16Mbit Serial FLASH 15 LDQM 16 WE# 35 A11 26 A3 22 A10/AP 32 A7 24 A1 34 A9 25 A2 29 A4 30 A5 33 A8 41 VSS2 4 DQ1 11 DQ6 31 A6 19 CS# 44 DQ9 7 DQ3 8 DQ4 50 DQ13 53 DQ15 2 DQ0 45 DQ10 37 CKE 48 DQ12 13 QD7 42 DQ8 5 DQ2 47 DQ11 10 DQ5 51 DQ14 23 A0 28 VSS1 54 VSS3 6 VSSQ1 12 VSSQ2 46 VSSQ3 52 VSSQ 40 NC/RFU 36 A12/NC 20 BA0 21 BA1 1 VDD1 14 VDD2 27 VDD3 3 VDDQ1 9 VDDQ2 43 VDDQ3 49 VDDQ4 39 UDQM 38 CLK 17 CAS# 18 RAS# U201 SD57D281642P C219 100nF C218 1uF C224 100nF C217 100nF C216 10nF 1 CE# 2 SO 3 WP# 4 VSS 5 SI 6 SCK 7 HOLD# 8 VDD U2 TSI25VF016 R52 47K C76 100nF R59 47K R60 33R R61 33R R6233R R41 33R R54 10K R53 10K C7 100nF 1 CD/DAT3 2 CMD 4 VDD 5 CLK 3 VSS 7 DAT0 8 DAT1 9 DATA2 10 11 12 6 VSS1 JS1 R9 10K R30 10K R36 10K R37 10K R27 10K VDD33 VDD33 SDRAM_WR SDRAM_CS BA1 SDRAM_CAS SDRAM_RAS BA0 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 MBE1 MBE0 SDRAMCLK+ SDRAMCKE D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 VDD33 SPI_CS SPI_DIN VDD33 SPI_CLK SPI_DOUT VDD33 SDIO_CMD SDIO_MCK SDIO_D3 SDIO_D2 VDD33 SDIO_D1 SDIO_D0 SDIO_CD A[0:11] TX6477-0214-V4.sch-5 - Tue Feb 14 17:09:28 2012 option sod-523 C21 10nF C40 4.7uF 2 VSS 1 VIN 4 NC 3 CE 5 VOUT U3 XC6204B332MR C14 100nF 1 2 MIC1 C8 100nF + C4 10uF R182.2K C11 100pF R26 1M Q2 SI2305P R25 47K 3 1 2 Q1 8050C 12 D1 IN4001 C5 100nF SW5 Reset C20 22uF 5 GND 4 NC 3 DP 1 VBUS 2 DM 6 NC3 7 NC4 8 NC2 9 NC1 J2 B型USB插座 5Pin R14 0R R15 2.2K 3 1 2 Q3 8050C R7 47K R8 100K R20 200K R13 10K C2 4.7nF R31 1.2K C15 100nF C16 NC R32680R 3 1 2 Q4 MMBT3904 R39 1K R40 100R SW2 PALY ON/OFF R5 2K 12 D4 RB521S 12 D8 RB521S 12 D11 RB521S C18 100nF + C115 10uF GND GND AVDD33 VBAT GND MIC_P GND LI_4.2V POWER_OFF VBAT USB_5V USB_5V USBDM USBDP GND VCM3 AVDD33 USB_BOOT MOVEDET POWER_KEY CONTROL TX6477-0214-V4.sch-6 - Tue Feb 14 17:09:28 2012 0308 NC 0308 NC + C102 4.7uF C103 100nF FB7 600ohm C104 100nF C106 NC/100nF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 J14 CAMERA R6 10K R16 10K R3 NC/1K C6 1uF R1 1K R21K R4 10K C3 1uF 3 VIN 2 VOUT 1 GND U4 XC6206P182M + C10 NC/22uF + C12 22uF R11 470R D2 LED_RED R12 470R D5 LED_BLUE 2 VSS 1 VIN 4 NC 3 CE 5 VOUT U6 XC6204B282MR R17 10K VBAT +2V8C VDD33 CAR3_0 CAR3_0 CAM_PWDN CIS_VISCLK CIS_VIVREF CIS_VIPCLK CIS_VIHREF I2CSDA I2CSCLK CAM_NRESET CIS_VIPIXEL5 CIS_VIPIXEL6 CIS_VIPIXEL7 CIS_VIPIXEL2 CIS_VIPIXEL1 CIS_VIPIXEL3 CIS_VIPIXEL0 CIS_VIPIXEL4 CIS_VIPIXEL[0:7] CAR1_8 VDD33 CAR1_8 SPI_DOUT I2CSDA I2CSCLK CAM_PWDN VBAT UART2_TXD UART2_RXD VDD33 +2V8C VDD33 VDD33 CAM_NRESET SPI_CLK TX6477-0214-V4.sch-7 - Tue Feb 14 17:09:28 2012 电源转换部分电路 控制线、移动侦测均为高电平有效 定位孔 3 SW1 7 VIN 8 EN 2 MODE/SYNC 1 RT 4 SW2 6 VOUT 9 FB 10 VC 5 GND U605 HX8001 HX8001 R627 10K + C602 10uF R628 100K 1 1 2 2 L60110uH C615 1.5nF R629 15K R631 499K R632 200K C616 100nF + C617 10uF…

Text truncated - open the document above for the full version.

TX6477-0214-V4.sch-2 - Tue Feb 14 17:09:27 2012 SD卡数据线 R101 22K D100 RB521S MEMORY BUS GPIO,PWM Camara,SPI,I2S,UART ANYKA AK3751B_BGA100 K6 RTC_WU_WD A5 #DRAM_WE B6 #DRAM_RAS G7 DRAM_DM[1] G6 DRAM_DM[0] F3 MDATA[9] E6 MDATA[8] E3 MDATA[7] E2 MDATA[6] D2 MDATA[5] C2 MDATA[4] A1 MDATA[3] A3 MDATA[2] H6 MDATA[15] F7 MDATA[14] F6 MDATA[13] G4 MDATA[12] G2 MDATA[11] E1 MDATA[10] B4 MDATA[1] B5 MDATA[0] C4 #DRAM_CS D1 DRAM_CLK H5 DRAM_CKE A6 #DRAM_CAS C3 DRAM_BANK1 B1 DRAM_BANK0 F4 MADDR[9] E5 MADDR[8] E4 MADDR[7] F2 MADDR[6] D3 MADDR[5] C1 MADDR[4] B2 MADDR[3] A2 MADDR[2] G5 MADDR[12]/GPIO46_PD G3 MADDR[11]/GPIO45_PD F5 MADDR[10] B3 MADDR[1] A4 MADDR[0] H8 #RST F9 UART_TXD/GPIO3_PU F8 UART_RXD/GPIO4_PU C9 SPI_DIN B10 MMC_D7/SDIO_D3/GPIO11_PU C10 MMC_D6/SDIO_D2/GPIO10_PU A7 MMC_D5/SDIO_D1/GPIO9_PU D8 MMC_D4/SDIO_D0/GPIO8_PU B9 SPI_DOUT/GPIO14_PU G8 SDIO_MCK/GPIO13_PU A10 SPI_CLK/GPIO15_PU B7 MMC_MCMD/SDIO_MCMD/GPIO6_PU C8 #SPI_CS/GPIO40_PD J1 VIVREF/GPIO22_PD H3 VISCLK/GPIO39_PD J4 VIPCLK/GPIO38_PD K2 VIHREF/GPIO23_PD J3 VI_D7/GPIO37_PD H2 VI_D6/GPIO36_PD F1 VI_D5/GPIO35_PD G1 VI_D4/GPIO34 J2 VI_D3/GPIO33 H1 VI_D2/GPIO32 K3 VI_D1/GPIO31 K1 VI_D0/GPIO30 K4 DGPIO[0]/GPIO47_PD U1-A AK3751B_BGA100 C101 1uF 12 D10 RB521S R101K VDD33 SDRAM_CS SDRAM_RAS SDRAM_WR SDRAMCLK+ SDRAMCKE BA0 BA1 UART2_TXD UART2_RXD SDRAM_CAS MBE1 MBE0 CIS_VIPCLK CIS_VIHREF CIS_VISCLK CIS_VIVREF SDIO_CMD SDIO_MCK POWER_OFF SPI_CS SPI_DIN SPI_DOUT SPI_CLK CIS_VIPIXEL7 CIS_VIPIXEL6 CIS_VIPIXEL5 SPI_CS SPI_DIN SPI_CLK CIS_VIPIXEL4 CIS_VIPIXEL3 CIS_VIPIXEL2 CIS_VIPIXEL1 CIS_VIPIXEL0 SPI_DOUT A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 RESET RESET SDIO_D0 SDIO_D1 SDIO_D2 SDIO_D3 USB_BOOT A[0:11] SDIO_CD USB_5V TX6477-0214-V4.sch-3 - Tue Feb 14 17:09:28 2012 1.5V 3.0V C169/C170紧挨着E8 脚放置； C177/C178紧挨着D4 脚放置； C173/C174紧挨着B8 脚放置； C175/C176紧挨着D5 脚放置； C183/C184紧挨着D6 脚放置； C167/C168紧挨着C5 脚放置； LayOut时电容尽量紧挨所对应PIN脚 C171/C180紧挨着K10 脚放置； C107/C108紧挨着E10 脚放置； 默认为AVCC3V3供电， 也就是模拟电源供电。 C174 4.7uF + C163 10uF C183 100nF C175 100nF + C168 10uF R144220K + C177 10uF C15422pF + C117 22uF C116 100nF C114 18pF R1251M C118 100nF C113 18pF CLOCK/PLL POWER PMU AUDIO/ADC USB_OTG ANYKA AK3751B_BGA100 J5 XTAL32KO K5 XTAL32KI D9 XTAL12MO D10 XTAL12MI J10 VMID_VCM2 K9 VDDMIC_VCM3 E10 VDDA/VDD(PLL) F10 OTG_RREF G10 OTG_DP G9 OTG_DM K8 MICP J7 HPR K7 HPL J6 AVSS(AUDIO) H7 AVDD33(AUDIO) H9 VSS(USB) J8 RTC_BAT_IN_AD4 J9 AIN_AD5 C7 VSS2 H4 VSS4 D7 VSS3 E9 VSS(PLL) C6 VSS1 K10 VREF_1V5 E7 VIN_LDO33 A9 VIN_BK_LDO12 D4 VDDIO3 C5 VDDIO1 D6 VDD3 D5 VDD1 A8 SW12 E8 LDO33_OUT/VDDIO B8 LDO12_OUT H10 VCC(USB) U1-B AK3751B_BGA100 + C156 4.7uF C166 100nF C171 100nF C169 100nF C167 100nF R113 NC/0R + C176 22uF + C184 10uF R123 10M R105 10K C107 100nF D102 IN5819 L101 10uH C164 100nF C162 100nF + C165 22uF C153 22pF C170 4.7uF C155 100nF C180 22uF C108 1uF C173 100nF C9 1uF C1 100nF 12 Y1 12MHz 1 2 Y2 32.768KHz R230R R19NC/0R POWRDET VREF_1V5 VBAT VDD1V2 VDD1V2 VDD33 VDD33 VBAT AVDD33 VCM3 USBDP VCM2 VCM3 MIC_P USBDM VCM2 AVDD33 VDD1V2 GND VREF_1V5 VDD1V2 VDD1V2 VDD1V2 VDD33 VDD33 12MI 12MO 32KI 32KO 32KO 32KI 12MO 12MI GND GND GND POWER_KEY GND GND VBAT LI_4.2V TX6477-0214-V4.sch-4 - Tue Feb 14 17:09:28 2012 16Mbit Serial FLASH 15 LDQM 16 WE# 35 A11 26 A3 22 A10/AP 32 A7 24 A1 34 A9 25 A2 29 A4 30 A5 33 A8 41 VSS2 4 DQ1 11 DQ6 31 A6 19 CS# 44 DQ9 7 DQ3 8 DQ4 50 DQ13 53 DQ15 2 DQ0 45 DQ10 37 CKE 48 DQ12 13 QD7 42 DQ8 5 DQ2 47 DQ11 10 DQ5 51 DQ14 23 A0 28 VSS1 54 VSS3 6 VSSQ1 12 VSSQ2 46 VSSQ3 52 VSSQ 40 NC/RFU 36 A12/NC 20 BA0 21 BA1 1 VDD1 14 VDD2 27 VDD3 3 VDDQ1 9 VDDQ2 43 VDDQ3 49 VDDQ4 39 UDQM 38 CLK 17 CAS# 18 RAS# U201 SD57D281642P C219 100nF C218 1uF C224 100nF C217 100nF C216 10nF 1 CE# 2 SO 3 WP# 4 VSS 5 SI 6 SCK 7 HOLD# 8 VDD U2 TSI25VF016 R52 47K C76 100nF R59 47K R60 33R R61 33R R6233R R41 33R R54 10K R53 10K C7 100nF 1 CD/DAT3 2 CMD 4 VDD 5 CLK 3 VSS 7 DAT0 8 DAT1 9 DATA2 10 11 12 6 VSS1 JS1 R9 10K R30 10K R36 10K R37 10K R27 10K VDD33 VDD33 SDRAM_WR SDRAM_CS BA1 SDRAM_CAS SDRAM_RAS BA0 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 MBE1 MBE0 SDRAMCLK+ SDRAMCKE D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 VDD33 SPI_CS SPI_DIN VDD33 SPI_CLK SPI_DOUT VDD33 SDIO_CMD SDIO_MCK SDIO_D3 SDIO_D2 VDD33 SDIO_D1 SDIO_D0 SDIO_CD A[0:11] TX6477-0214-V4.sch-5 - Tue Feb 14 17:09:28 2012 option sod-523 C21 10nF C40 4.7uF 2 VSS 1 VIN 4 NC 3 CE 5 VOUT U3 XC6204B332MR C14 100nF 1 2 MIC1 C8 100nF + C4 10uF R182.2K C11 100pF R26 1M Q2 SI2305P R25 47K 3 1 2 Q1 8050C 12 D1 IN4001 C5 100nF SW5 Reset C20 22uF 5 GND 4 NC 3 DP 1 VBUS 2 DM 6 NC3 7 NC4 8 NC2 9 NC1 J2 B型USB插座 5Pin R14 0R R15 2.2K 3 1 2 Q3 8050C R7 47K R8 100K R20 200K R13 10K C2 4.7nF R31 1.2K C15 100nF C16 NC R32680R 3 1 2 Q4 MMBT3904 R39 1K R40 100R SW2 PALY ON/OFF R5 2K 12 D4 RB521S 12 D8 RB521S 12 D11 RB521S C18 100nF + C115 10uF GND GND AVDD33 VBAT GND MIC_P GND LI_4.2V POWER_OFF VBAT USB_5V USB_5V USBDM USBDP GND VCM3 AVDD33 USB_BOOT MOVEDET POWER_KEY CONTROL TX6477-0214-V4.sch-6 - Tue Feb 14 17:09:28 2012 0308 NC 0308 NC + C102 4.7uF C103 100nF FB7 600ohm C104 100nF C106 NC/100nF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 2526 J14 CAMERA R6 10K R16 10K R3 NC/1K C6 1uF R1 1K R21K R4 10K C3 1uF 3 VIN 2 VOUT 1 GND U4 XC6206P182M + C10 NC/22uF + C12 22uF R11 470R D2 LED_RED R12 470R D5 LED_BLUE 2 VSS 1 VIN 4 NC 3 CE 5 VOUT U6 XC6204B282MR R17 10K VBAT +2V8C VDD33 CAR3_0 CAR3_0 CAM_PWDN CIS_VISCLK CIS_VIVREF CIS_VIPCLK CIS_VIHREF I2CSDA I2CSCLK CAM_NRESET CIS_VIPIXEL5 CIS_VIPIXEL6 CIS_VIPIXEL7 CIS_VIPIXEL2 CIS_VIPIXEL1 CIS_VIPIXEL3 CIS_VIPIXEL0 CIS_VIPIXEL4 CIS_VIPIXEL[0:7] CAR1_8 VDD33 CAR1_8 SPI_DOUT I2CSDA I2CSCLK CAM_PWDN VBAT UART2_TXD UART2_RXD VDD33 +2V8C VDD33 VDD33 CAM_NRESET SPI_CLK TX6477-0214-V4.sch-7 - Tue Feb 14 17:09:28 2012 电源转换部分电路 控制线、移动侦测均为高电平有效 定位孔 3 SW1 7 VIN 8 EN 2 MODE/SYNC 1 RT 4 SW2 6 VOUT 9 FB 10 VC 5 GND U605 HX8001 HX8001 R627 10K + C602 10uF R628 100K 1 1 2 2 L60110uH C615 1.5nF R629 15K R631 499K R632 200K C616 100nF + C617 10uF…

Text truncated - open the document above for the full version.

Test Report of FCC Part 15 C for FCC Certificate On Behalf of SHENZHEN XI LONG ELECTRONICS CO., LTD Product description: PIR motion sensor with hidden camera,SD recorder Model No.: PIR-SD FCC ID: WO9- PIR-SD Prepared for: SHENZHEN XI LONG ELECTRONICS CO., LTD No.2201, bldg.2, duoli industrial park, no.105, mei hua road, shang meilin, fu tian, shen zhen city, guang dong, china, Prepared by: Bontek Compliance Testing Laboratory Ltd 1/F, Block East H-3, OCT Eastern Ind. Zone, Qiaocheng East Road, Nanshan, Shenzhen, China Tel: 86-755-86337020 Fax: 86-755-86337028 Report No.: BCT13AR-0085E-1 Issue Date: May 2, 2013 Test Date: March 25~ May 2, 2013 Tested by: Reviewed by: Lion Cai Kendy Wang Approved by: Tony Wu Report No.: BCT13AR-0085E-1 Page 2 of 23 FCC ID: WO9-PIR-SD TABLE OF CONTENTS 1．GENERAL INFORMATION ........................................................................................................................................ 4 1.1 Product Description for Equipment Under Test (EUT) .............................................................. 4 1.2 Test Standards........................................................................................................................... 4 1.3 Test Facility ................................................................................................................................ 4 2. SYSTEM TEST CONFIGURATION .............................................................................................................................. 6 2.1 EUT Configuration ..................................................................................................................... 6 2.2 EUT Exercise ............................................................................................................................. 6 2.3 General Test Procedures .......................................................................................................... 6 2.4 Measurement Uncertainty ......................................................................................................... 6 2.5 Test Equipment List and Details ................................................................................................ 7 3. SUMMARY OF TEST RESULTS.................................................................................................................................. 8 4．DISTURBANCE VOLTAGE AT THE MAINS TERMINALS ........................................................................................ 9 4.1 Measurement Uncertainty ......................................................................................................... 9 4.2 Applicable Standard ................................................................................................................... 9 4.3 Test Setup Diagram ................................................................................................................... 9 4.4 Test Result ................................................................................................................................. 9 5. RADIATED DISTURBANCES .................................................................................................................................... 12 5.1 Measurement Uncertainty ....................................................................................................... 12 5.2 Limit of Radiated Disturbances ............................................................................................... 12 5.3 EUT Setup ............................................................................................................................... 12 5.4 Test Receiver Setup ................................................................................................................ 13 5.5 Test Procedure ........................................................................................................................ 13 5.6 Corrected Amplitude & Margin Calculation ............................................................................. 14 5.7 Radiated Emissions Test Result ............................................................................................. 14 6. 20DB BANDWIDTH .................................................................................................................................................... 17 6.1 Measurement Uncertainty ....................................................................................................... 17 6.2 Limit of 20dB Bandwidth .......................................................................................................... 17 6.3 EUT Setup ............................................................................................................................... 17 6.4 Test Procedure ........................................................................................................................ 17 6.5 Emissions within Band Edges Test Result .............................................................................. 18 7. DUTY CYCLE ............................................................................................................................................................. 18 7.1 Measurement Uncertainty ....................................................................................................... 19 7.2 EUT Setup ............................................................................................................................... 19 7.3 Test Procedure ........................................................................................................................ 19 7.4 Measurement Result ................................................................................................................ 19 8. TRANSMISSION TIME ............................................................................................................................................... 21 8.1 Measurement Uncertainty ...........…

Text truncated - open the document above for the full version.

Test Report of FCC Part 15 C for FCC Certificate On Behalf of SHENZHEN XI LONG ELECTRONICS CO., LTD Product description: PIR motion sensor with hidden camera,SD recorder Model No.: PIR-SD FCC ID: WO9- PIR-SD Prepared for: SHENZHEN XI LONG ELECTRONICS CO., LTD No.2201, bldg.2, duoli industrial park, no.105, mei hua road, shang meilin, fu tian, shen zhen city, guang dong, china, Prepared by: Bontek Compliance Testing Laboratory Ltd 1/F, Block East H-3, OCT Eastern Ind. Zone, Qiaocheng East Road, Nanshan, Shenzhen, China Tel: 86-755-86337020 Fax: 86-755-86337028 Report No.: BCT13AR-0085E-1 Issue Date: May 2, 2013 Test Date: March 25~ May 2, 2013 Tested by: Reviewed by: Lion Cai Kendy Wang Approved by: Tony Wu Report No.: BCT13AR-0085E-1 Page 2 of 23 FCC ID: WO9-PIR-SD TABLE OF CONTENTS 1．GENERAL INFORMATION ........................................................................................................................................ 4 1.1 Product Description for Equipment Under Test (EUT) .............................................................. 4 1.2 Test Standards........................................................................................................................... 4 1.3 Test Facility ................................................................................................................................ 4 2. SYSTEM TEST CONFIGURATION .............................................................................................................................. 6 2.1 EUT Configuration ..................................................................................................................... 6 2.2 EUT Exercise ............................................................................................................................. 6 2.3 General Test Procedures .......................................................................................................... 6 2.4 Measurement Uncertainty ......................................................................................................... 6 2.5 Test Equipment List and Details ................................................................................................ 7 3. SUMMARY OF TEST RESULTS.................................................................................................................................. 8 4．DISTURBANCE VOLTAGE AT THE MAINS TERMINALS ........................................................................................ 9 4.1 Measurement Uncertainty…

Text truncated - open the document above for the full version.