WO9-XSJ-87LWIRELESS SMART DOOR/WINDOW SENSOR

Wireless Smart Door Sensor Functions/Features: Mainly detect open/close states of doors and windows, generally set as a 1 st Defense Line or perimeters. If any doors or windows are opened, it will transmit the alarm signal to notify the alarm host. Automatically detect the open/close of the doors and windows and send state signal to the host. Specifications:
Operating power: 23A 12V Battery (Recommended: alkaline battery)
Wireless transmitting: distance: ≥450ft (in open area
Service life: ≤2 years
Alarm distance: ＜4cm. Installation and Usage: Mount the magnet or smaller piece onto the door in a position of about 5~6ft above the ground to prevent any child(ren) to pampering. Use the included mounting bracket if the door and the door frame are un5even or not flush. Mount the emitting or larger piece onto the door frame, ensure the magnet piece and the emitting piece are even or flush. The spaces between the two should be less than 10mm in gap. Replace the batteries if the blue LED light flashes frequently. Adding and Cancelling Smart Door/Window Sensor A. Add Press _Set + Password + ENT _ then. _70 + ENT + XX + ENT 5555555The “Learn” light will appear solid red. Note: The XX indicates group number of the defense zones, including zone 06 through 10. Press the smart door/window sensor twice consecutively, if you hear “Di5555” form the alarm host and see the “Learn” light flashes five times and off, it indicates successfully added. B. To Cancel: Press _Set + Password + ENT _ then. _71 + ENT + XX + ENT 5555555The alarm host will beep twice then the “Learn” light will flash once and then turns off to indicate the doorbell button has been successfully cancelled. Note: The alarm host can only learn 1 wireless device (Wireless Smart Door/Window Sensor) at one time, a total of 4 wireless Devices (Wireless Smart Door/Window Sensors) to a zone/group can be added. For example, if 4 sensors were to be added to zone/group 01 through zone/group 15, it total 60 sensors in all. If 1 device is removed from a group that has 4 devices, then all 4 devices in the group will be automatically removed, and each device(s) will have to be added again to the alarm host. Enabling and Activating Smart Zone Function (After adding smart door/window sensor successfully) Press _Set + Password + ENT _ then. _91 + ENT + XX + ENT 5555555The alarm host will beep twice to indicate the smart zone function has been enabled.( Note: The XX indicates group number of the defense zones, including zone 06 through 10.) To activate smart zone function by putting the magnet (or smaller piece) and the emitting (or larger piece) together to get closed when the host is in working status. Note: 1. When arming the host, if the door/window with the smart door/window sensor installed is on, the LED light of the corresponding zone will appear solid red, at the same time the host will beep every 2 seconds within 30 seconds. 2. You can arm again to make a force arm. 3. If press “ESC” or wait the host to get out of arm operation automatically in 30 seconds. LED light turns off to indicate unsuccessful arm. 4. If the smart zone function is not enabled and activated, it can only work as a general door/window sensor.

433.92M OSCILATOR RF AMPLIFIER RF MODULATOR IC ENCODER DC 12V POWER SUPPLY Antenna Block Diagram

深圳市华标电子科技有限公司 Bontek Compliance Testing Laboratory Ltd DATE: October 09, 2011 Dear TCB Section of Timco Engineering, Inc., Thank you for cooperation. I would like to submit FCC application of Shenzhen Xi Long Electronics Co.,Ltd. . FCC ID: WO9-XSJ-87L by your TCB Approval today. Best Regards, Bontek Compliance Testing Laboratory Ltd. Tony Wu/General Manager

Shenzhen Xi Long Electronics Co.,Ltd. No. 2201, Bldg. 2, Duoli Industrial Park, No.105 Meihua Road, Shang Meilin, Futian, Shenzhen-518049,Guangdong,China October 9, 2011 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC Application for FCC ID: WO9-XSJ-87L To Whom it may Concern: This letter is to ascertain that Shenzhen Xi Long Electronics Co.,Ltd. Product has been the units used for conducting FCC compliance testing,the DoC part will be tested by FCC recognized test lab. Best regards Sincerely, Shenzhen Xi Long Electronics Co.,Ltd. Mary Zhong (Sales Manager)

SHENZHEN HANGSHENG ELECTRONICS CO.,LTD. FCC ID: WO9-XSJ-87L POWER OF ATTORNEY October 9, 2011 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Bontek Compliance Testing Laboratory Ltd.(Tony Wu) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Bontek Compliance Testing Laboratory Ltd. (Tony Wu) on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act.We, Shenzhen Xi Long Electronics Co.,Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuantto that section. Sincerely, Shenzhen Xi Long Electronics Co.,Ltd. Mary Zhong (Sales Manager)

External Photographs EUT –Front View EUT – Rear View

FCC ID Label Sample for FCC ID: WO9-XSJ-87L FCC ID: WO9-XSJ-87L Model: XSJ-87L

FCC ID Location FCC ID Location

Internal Photographs EUT - Open View EUT - PCB View

DESCRIPTION OF OPERATION The EUT is a 433.92 MHz transmitter. When the button of the EUT is pressed, The encoder will generates a digital code serially transmit into the Central Processor Unit (modulator or called as mixer) in circuit. The serially digital signal was mixed at modulator (mixer) stage by way of AM mode (Amplitude Modulation) with the carrier, which is generate by the 433.92MHz oscillator, and then this signal was amplified and sent to the Transmitter antenna. The Antenna is printed in the PCB The tramsmitter is powered by the 12V battery.

123456 A B C D 6 54321 D C B A Title NumberRevisionSize B Date:25-Aug-2011Sheet of File:E:\工作文件\探测器类\无线探测器\XSJ-87无线门磁\智能门磁（23A电池）\智能门磁（23A电池）_V4.4\DDB\智能门磁（23A电池 ）Drawn By: DS1 磁管 VCC 1 2 J1 电池片 R2 10M R3 1.5M R1 1M R4 4.7M VCC Q3 8050 XSJ-87_V1.0(新开模外壳) p3.6/RST 1 P3.0/RXD/INT 2 P3.1/TXD 3 XTAL2 4 XTAL1 5 P3.3/INT1 6 P3.4/T0/INT/CLKOUT 7 GND 8 P3.7 9 P1.0 10 P1.1 11 P1.2 12 P1.5 13 P1.6/RXD/INT 14 P1.7/TXD 15 VCC 16 U2 STC11L01E R5 2M 23 1 VinVout GND U1 7530 贴片 Q5 8050 GUAN KAI Q4 8050 diya BATA BATA BATA R6 10M diya C17 104 VCC fashe Y2 4M C15 20P C14 20P C13 10UF/10V-3216 R8 10K RXD TXD VCC 1 2 3 4 J2 ISP VCC RXD TXD R7 4.7k 1 1 2 2 LED 工作指示灯白发蓝 VCC 智能门磁 C11 100uf/10v-3528 GUAN KAI Q1 3357 2 1 3 Y1 433MHZ Q2 3356 L2 小7T5 L1 小7T5 C1 5.6P R10 10K C2 2P R9 0R VCC fashe 布线电感 ANT 公司机密 PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn

Test Report of FCC Part 15 C for FCC Certificate On Behalf of Shenzhen Xi Long Electronics Co.,Ltd. Product description: Wireless smart door/window sensor Model No.: XSJ-87L FCC ID: WO9-XSJ-87L Prepared for: Shenzhen Xi Long Electronics Co.,Ltd. No. 2201, Bldg. 2, Duoli Industrial Park, No.105 Meihua Road, Shang Meilin, Futian, Shenzhen-518049,Guangdong,China Prepared by: Bontek Compliance Laboratory Ltd 1/F, Block East H-3, OCT Eastern Ind. Zone, Qiaocheng East Road, Nanshan, Shenzhen, China Tel: 86-755-86337020 Fax: 86-755-86337028 Report No.: BCT11HR-1300E Issue Date: October 9, 2011 Test Date: October 1~9, 2011 Test by: Reviewed By: Kendy Wang Tony Wu Report No.: BCT11HR-1300E Page 2 of 22 TABLE OF CONTENTS 1 - GENERAL INFORMATION ......................................................................................................................................... 4 1.1 Product Description for Equipment Under Test (EUT)..............................................................4 1.2 Test Standards...........................................................................................................................4 1.3 Test Summary............................................................................................................................4 1.4 Test Methodology ......................................................................................................................5 1.5 Test Facility................................................................................................................................5 1.6 Test Equipment List and Details................................................................................................7 2 - SYSTEM TEST CONFIGURATION............................................................................................................................. 9 2.1 Justification ................................................................................................................................9 2.2 EUT Exercise Software .............................................................................................................9 2.3 Equipment Modifications ...........................................................................................................9 2.4 Basic Test Setup Block Diagram...............................................................................................9 3 – DISTURBANCE VOLTAGE AT THE MAINS TERMINALS ..................................................................................... 11 3.1 Measurement Uncertainty .......................................................................................................11 3.2 Applicable Standard.................................................................................................................11 3.3 Test Description .......................................................................................................................11 4- RADIATED DISTURBANCES.................................................................................................................................... 12 4.1 Measurement Uncertainty .......................................................................................................12 4.2 Limit of Radiated Disturbances ...............................................................................................12 4.3 EUT Setup ...............................................................................................................................12 4.4 Test Receiver Setup ................................................................................................................13 4.5 Test Procedure ........................................................................................................................13 4.6 Corrected Amplitude & Margin Calculation .............................................................................14 4.7 Radiated Emissions Test Result .............................................................................................14 5- 20DB BANDWIDTH ................................................................................................................................................... 16 5.1 Measurement Uncertainty .......................................................................................................16 5.2 Limit of 20dB Bandwidth ..........................................................................................................16 5.3 EUT Setup ...............................................................................................................................16 5.4 Test Procedure ........................................................................................................................16 5.5 Emissions within Band Edges Test Result..............................................................................17 6- DUTY CYCLE............................................................................................................................................................. 18 6.1 Measurement Uncertainty .......................................................................................................18 6.2 EUT Setup ...............................................................................................................................18 6.3 Test Procedure ........................................................................................................................18 6.4 Measurement Result................................................................................................................18 7- TRANSMISSION TIME............................................................................................................................................... 20 7.1 Measurement Uncertainty .......................................................................................................20 7.2 EUT Setup .........................…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOGRAPHS Radiated Emission