WP4HPZM2ZIGBEE WIRELESS MODULE

HPZM2 USER’S MANUAL JULY 10 2014 HPZM2 USER’S MANUAL JULY 10 2014 Contains FCC ID: HPZM2 United States (FCC) This equipment complies with Part 15 of the FCC rules and regulations. To fulfill FCC Certification requirements, and OEM manufacturer must comply with the following regulations: (1) The modular transmitter must be labelled with its own FCC ID number, and, if the FCC ID number is not visible when the module is installed inside another advice, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Example of label required for OEM product containing HPZM2 module WARNING: The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter must be labelled with its own FCC ID number. This includes a clearly visible label on the outside of the final product enclosure that displays the content shown below. If the FCC ID is not visible then the outside of the device into which the module is installed must also display a label referring to the enclosed equipment. IMPORTANT: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (FCC 15.19). The internal / external antenna(s) used for this mobile transmitter must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. IMPORTANT: The module is limited to OEM installation only. OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module. The module is limited to installations in mobile or fixed applications, according to Part 2.1091(b). Separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. IMPORTANT: OEM integrators must include the following instructions and statements in the user manual (i.e. end product): (1) statements and labeling as required per Part 15.19 and 15.21, and (2) end-users must be provided with transmitter/antenna installation requirements and operating conditions for satisfying RF exposure compliance: (i) a separate section should clearly state “FCC RF Exposure requirements”, (ii) Required operating conditions for end users, (iii) antenna or transmitter installation requirements where relevant (i.e. “ The internal / external antenna(s) used for this mobile transmitter must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”) HPZM2 USER’S MANUAL JULY 10 2014 For HPZM2 module: IC: 9709A-HPZM2 AXXESS HPZM2 ZRM HPZM2 Canada (IC) Equipment is subject to certification under the applicable RSSs, shall be permanently labelled on each item, or as an inseparable combination. The label must contain the following information for full compliance: The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labelled to display the Industry Canada certification number of the module, preceded by the words “Contains transmitter module”, or the word “Contains”, or similar wording expressing the same meaning, as follows: Contains transmitter module IC: 9709A-HPZM2 The applicant for equipment certification of the module shall provide with each unit of the module either a label such as described above, or an explanation and instructions to the user as to the host device labelling requirements. IMPORTANT: This equipment for which a certificate has been issued is not considered certified if it is not properly labelled. The information on the Canadian label can be combined with the manufacturer’s other labelling requirements. IMPORTANT: Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1( l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. IMPORTANT: To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. The antenna used with this module must be installed to provide a separation distance of at least 20cm from all persons, and must not transmit simultaneously with any other antenna or transmitter. Conformément à la réglementation d'Industrie Canada, le présent éemetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. IMPORTANT: The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population. Consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca/rpb. HPZM2 USER’S MANUAL JULY 10 2014 The HPZM2 Module has been certified …

Text truncated - open the document above for the full version.

June 26, 2014 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Re: Axxess Industries Inc FCC ID: WP4HPZM2 Request for Long-Term Confidentiality Pursuant to 47 CFR 0.457(d) and 47 CFR 0.459 of the FCC Rules, Axxess Industries Inc. hereby requests long-term confidentiality of the following exhibits: Exhibit Type File Name Block Diagram HPZM2 Block Diagram.pdf Schematic Diagrams HPZM2 Schematic.pdf Parts List HPZM2 Parts List.pdf Operational Description HPZM2 Theory of Operation-Technical Description.pdf These documents contain detailed system and equipment description and related information about the product in which Axxess Industries Inc. considers proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, Axxess Industries Inc. considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, _________________ Joerg Wagner President Axxess Industries Inc.

MODEL: HPZM2 FCC ID: WP4HPZM2 IC: 9709A-HPZM2 MODEL: HPZM2 FCC ID: WP4HPZM2 IC: 9709A-HPZM2 29 APRIL 2013 1 HPZM2

Axxess Industries Inc. | 103-470 Neave Court | Kelowna, BC, Canada | V1V 2M2 HPZM2 Transmit Power Reduction Tuning Procedure The HPZM2 module is programmed at the factory with firmware intended to limit the output transmit power to within acceptable limits, in accordance with Part 15.247 FCC Rules. In the case of the HPZM2 module that is -10dB from full transmit power capabilities, for a maximum transmit power not to exceed 19dB. The firmware is tested and approved in accordance with internal quality assurance procedures. The programmed module is set to transmit at relative full power and tested using calibrated RF power measurement equipment to ensure the device is within acceptable limits . The end user does not have the capabilities of increasing the reduced maximum transmit output power level.

19473 Fraser Way Pitt Meadows, BC Canada V3Y 2V4 ph. 604-527-8378 |fx. 604 527 8388 Electromagnetic Compatibility INTENTIONAL RADIATOR TEST REPORT IC RSS-210; FCC 47 CFR Part 15/C 15.247 Report Reference No. ...................: E10494-1401 Rev 2.0 Date of issue .....................................: July 08, 2014 Total number of pages...............: 27 Testing Laboratory.......................: Quality Auditing Institute Address............................................ : 16 – 211 Schoolhouse Street, Coquitlam, BC, V3K 4X9, Canada Accreditations (ISO 17025): Standard Council of Canada: Accredited Laboratory No. 743 International Accreditation Service Inc: Accredited Laboratory: No. TL-239 This report has been completed in accordance with the requirements of ISO/IEC 17025. Test results contained in this report are within QAI Laboratories ISO/IEC 17025 accreditation. QAI Laboratories authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for the use by the company’s employees only. Applicant’s name ........................: Axxess Industries Inc. Address..................................: 103-470 Neave Court, Kelowna BC, V1V 2M2, Canada Contact...................................: Joerg Wagner, [email protected] Phone.....................................: (250)469-9375 Fax: (250) 491-4715 Test Standard...........................: RSS-210 Issue 8, FCC 47 CFR Part15 Subpart C 15.247 Test item description...............: Zigbee Wireless Module (for use in Axxess products) Model....................................: HPZM2 Trade Mark ...........................: Manufacturer ................................: Axxess Industries Inc. Registrations: : FCC ID: WP4HPZM2 IC: 9709A-HPZM2 Client: Axxess Industries Ltd. Job No.: E10494-1401 Date: June 02, 2014 Page 2 of 27 HPZM2 Module Client: Axxess Industries Ltd. Job No.: E10494-1401 Date: June 02, 2014 Page 3 of 27 Revision History Date Report Number Rev # Details Authors Initials May 07, 2014 E10494-1401 0.0 Draft Test Report DJ June 02, 2014 E10494-1401 1.0 Release version with client requested changes DJ July 08, 2014 E10494-1401 2.0 Revised version additional setup photos and equipment list DJ Note: All previous versions of this report have been superseded by the latest dated revision as listed in the above table. Please dispose of all previous electronic and paper printed revisions accordingly. Client: Axxess Industries Ltd. Job No.: E10494-1401 Date: June 02, 2014 Page 4 of 27 Index Statement of Compliance ............................................................................................................................. 5 Testing Location and Procedures ................................................................................................................. 6 Product Description ...................................................................................................................................... 8 Test Results 9 Antenna Requirements ....................................................................................................... 9 Maximum Peak Conducted Output Power Level .............................................................. 10 Occupied Bandwidth ......................................................................................................... 11 Out Of Band Spurious Emissions Conducted .................................................................. 15 Out Of Band Spurious Emissions Radiated ..................................................................... 17 Power Spectral Density .................................................................................................... 19 Frequency Stability ........................................................................................................... 21 Duty Cycle Correction - Pulsed Train Average Time of Occupancy ................................ 23 EUT photos during the testing .................................................................................................................... 25 Client: Axxess Industries Ltd. Job No.: E10494-1401 Date: June 02, 2014 Page 5 of 27 Statement of Compliance The following tests demonstrate testimony for the FCC & IC Marks for Transceivers / electromagnetic compatibility testing for this EUT as required by FCC Part 15 Section 15.247 and IC RSS-210 Appendix8. Test / Requirement Description Applicable FCC Rule Parts Applicable Industry Canada Rule Parts Results Pass / Fail Limit Measured Antenna Requirement 15.203 RSS-Gen (7.1.2) Approved Antenna PCB Antenna Pass Maximum Peak Conducted Output Power Level 15.247 (b)(3) RSS-210 A8.4(4) Max Peak: 1W Max Peak EIRP 4W 18.7dBm 74mW Pass Emission Bandwidth (EBW) 15.247(a)(2); RSS-210 A8.2(a) Min. 500kHz 1.59MHz Pass RF Exposure Compliance 15.247 (b)(5) RSS-Gen (5.6) and RSS-102 (2.5) Exempt if greater than 20cm and less than 5 W Exempt SAR and RF Exposure Pass Spurious Emissions at antenna terminals 15.247 (d) RSS-210 A8.5 Min 20dBc 46dBc Pass Spurious Emissions Radiated Field Strength 15.247 (d) 15.205 (c) RSS-210 A8.5 RSS-Gen Min 20dBc and 54dBuv 2.0dB Margin Pass Maximum Power Spectral Density Level in Fundamental Emission 15.247 (e) RSS-210 A8.2(b) 8dBm 3.35dBm Frequency Stability 15.215 (c) RSS-Gen +/- 5.0ppm +/-0.01ppm Pass Duty Cycle Correction 15.247(a)(1) (iii) RSS-Gen. 20dB Pass Tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with CFR 47 FCC Part 15 and Industry Canada RSS-210. The manufacturer is responsible for the tested product configuration, continued product compliance with these standards listed, and for the appropriate auditing of subsequent products as required. X Tested By & Report Written By David Johanson, RF/EMC Test Engineer X Reviewed By Amandeep Jathaul RF/EMC Test Engineer Client: Axxess Industries Ltd. Job No.: E10494-1401 Date: June 02, 2014 Page 6 of 27 Testing Location and Procedures Testing Laboratory: Quality Auditin…

Text truncated - open the document above for the full version.

QAI Laboratories Axxess Industries HPZM2 – E10494‐1401 Setup Photos