WP4LPZM3RADIO COMMUNICATIONS MODULE

TITLE: DATE: REVISION: 19 JUNE 2013 LPZM3 USER’S MANUAL THIS DRAWING IS THE PROPERTY OF AXXESS INDUSTRIES INC. AND MAY BE NEITHER USED, COPIED, REPRODUCED OR OTHERWISE DEALT WITH NOR ITS CONTENTS COMMUNICATED TO OTHERS EXCEPT IN ACCORDANCE WITH WRITTEN INSTRUCTIONS RECEIVED FROM AXXESS INDUSTRIES INC. i n d u s t r i e s 103-470 NEAVE COURT KELOWNA BC CANADA V1V 2M2 1 866 680 2457 WWW.AXXIND.COM 2 JULY 2013 3 JULY 2013 UNITED STATES (FCC) This equipment complies with Part 15 of the FCC rules and regulations. To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following regulations: 1. The modular transmitter must be labelled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Example of label required for OEM product containing LPZM3 module WARNING: The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter must be labeled with its own FCC ID number. This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown below. If the FCC ID is not visible when the equipment is installed inside another device, then the outside of the device into which the equipment is installed must also display a label referring to the enclosed equipment. IMPORTANT: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (FCC 15.19). The internal / external antenna(s) used for this mobile transmitter must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Contains FCC ID: WP4LPZM3 The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any interference received, including interference that may cause undesired operation. TITLE: DATE: REVISION: 19 JUNE 2013 LPZM3 USER’S MANUAL THIS DRAWING IS THE PROPERTY OF AXXESS INDUSTRIES INC. AND MAY BE NEITHER USED, COPIED, REPRODUCED OR OTHERWISE DEALT WITH NOR ITS CONTENTS COMMUNICATED TO OTHERS EXCEPT IN ACCORDANCE WITH WRITTEN INSTRUCTIONS RECEIVED FROM AXXESS INDUSTRIES INC. i n d u s t r i e s 103-470 NEAVE COURT KELOWNA BC CANADA V1V 2M2 1 866 680 2457 WWW.AXXIND.COM 2 JULY 2013 3 JULY 2013 TITLE: DATE: REVISION: 19 JUNE 2013 LPZM3 USER’S MANUAL THIS DRAWING IS THE PROPERTY OF AXXESS INDUSTRIES INC. AND MAY BE NEITHER USED, COPIED, REPRODUCED OR OTHERWISE DEALT WITH NOR ITS CONTENTS COMMUNICATED TO OTHERS EXCEPT IN ACCORDANCE WITH WRITTEN INSTRUCTIONS RECEIVED FROM AXXESS INDUSTRIES INC. i n d u s t r i e s 103-470 NEAVE COURT KELOWNA BC CANADA V1V 2M2 1 866 680 2457 WWW.AXXIND.COM 2 JULY 2013 CANADA (IC) Equipment is subject to certification under the applicable RSSs, shall be permanently labelled on each item, or as an inseparable combination. The label must contain the following information for full compliance: For LPZM3 module: IMPORTANT: This equipment for which a certificate has been issued is not considered certified if it is not properly labelled. The information on the Canadian label can be combined with the manufacturer's other labelling requirements IMPORTANT: Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT: To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. IMPORTANT: The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population. Consult Safety Code 6, obtainable from Health Canada's website www.hc-sc.gc.ca/rpb. Certification Number: Manufacturer's Name, Trade Name or Brand Name: Model Name: IC: 9709A-LPZM3 AXXESS LPZM3 ZRM LPZM3 3 JULY 2013 EUROPEAN UNION (ETSI) The LPZM3 Module has been certified for use in European Union countries. If the is incorporated into a product, the manufacturer must ensure compliance of the final product to the European harmonized EMC and low-voltage/safety standards. A Declaration of Conformity must be issued for each of these standards and kept on file as described in Annex II of the R&TTE Directive. Furthermore, the manufacturer must maintain a copy of the LPZM3 Module documentation and ensure the final product does not exceed the specified power ratings, antenna specifications, and/or installation requirements as specified in the user manual. If any of these specifications are exceeded in the final product, a submission must be made to a notified body for compliance testing to all required standards. IMPORTANT: The 'CE' marking must be affixed to a visible location on the OEM product. The CE mark shall consist of the initials "CE" taking the following form: LPZM3 Module If the CE marking is reduced or enlarged, the proportions given in the above graduated drawing must be respected. The CE marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus. The CE marking must be affixed visibly, legibly, and indelibly. More detailed information about CE marking requirements you can find at "DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL" on 9 March 1999 at sec…

Text truncated - open the document above for the full version.

6454 Fitzgerald Rd. – Courtenay - British Columbia - V9J 1N7 PH 250-898-4567 – www.islandlabs.a To whom it may concern: Axxess Industries Inc. would like to apply for single modular FCC approval. This letter is our application for such according to FCC Part 15.212. Modular Transmitter Requirements Manufacturer Clarification 1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly A shield is provided on the module. 2. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal Signals are directly connected to the EM357 SoC which has buffered I/O ports. 3. The module must contain power supply regulation on the module The module generates 1v8 for RF circuitry 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b) The module has a PCB trace antenna with no external antenna options. 5. The module must demonstrate compliance in a stand-alone configuration The module was mounted on a bare carrier PCB for test purposes. Only power was supplied via the carrier PCB. 6. The module must be labelled with its permanently affixed FCC ID label, or use an electronic display FCC ID number is clearly shown on module. 7. The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements Module is shown to be compliant with 15.247 of the rules. 8. The module must comply with RF exposure requirements. Module complies with RF exposure requirements. See RF exposure exhibit for details.

April 15, 2013 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Re: Axxess Industries Inc FCC ID: WP4LPZM3 Request for Long-Term Confidentiality Pursuant to 47 CFR 0.457(d) and 47 CFR 0.459 of the FCC Rules, Axxess Industries Inc. hereby requests long-term confidentiality of the following exhibits: Exhibit Type File Name Block Diagram LPZM3 Block Diagram.pdf Schematic Diagrams LPZM3 Schematic.pdf Operational Description LPZM3 Theory of Operation-Technical Description.pdf These documents contain detailed system and equipment description and related information about the product in which Axxess Industries Inc. considers proprietary, confidential, and a custom design and, otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, Axxess Industries Inc. considers this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, _________________ Joerg Wagner President Axxess Industries Inc.

Island Compliance Services Inc. Axxess Industries Inc. Model: LPZM3 Page | 1 of 1 Island Compliance Services Inc. External Photographs Model LPZM3

MODEL: LPZM3 FCC ID: WP4LPZM3 IC: 9709A-LPZM3 MODEL: LPZM3 FCC ID: WP4LPZM3 IC: 9709A-LPZM3 8 APRIL 2013 3

Island Compliance Services Inc. Axxess Industries Inc. Model: LPZM3 Page | 1 of 2 Island Compliance Services Inc. Internal Photographs model LPZM3 Transmitter Island Compliance Services Inc. Axxess Industries Inc. Model: LPZM3 Page | 2 of 2 Island Compliance Services Inc.

Parts List Printed 4/15/2013 ItemQtyPart NumberTypeTitleReference VendorVendor P/NMfr NameMfr P/N AP-120 Assembly, PCB, LPZM3 LPZM3 Type Status Revision PL U 1 User1 User2 User3 User4 User5 Date By 4/12/2012 UnitRevDetail 11 each BN-001PSBALUN 2.4GHZ WIFI/BLUETOOTH 2450BL15B100E BLN1 Digikey712-1041-1-NDJohanson Technology Inc2450BL15B100E 22 each CS-084PSCAP CER 2.2UF 6.3V 10% X5R 0402 2.2uF 0402 C1 C22 Digikey445-6847-2-NDTDK CorporationC1005X5R0J225K 37 each CS-026PSCAP CER 0.1UF 10V 10% X5R 0402 0.1uF 0402 C2 C3 C4 C5 C6 C9 C21 Digikey587-1227-2-NDTaiyo YudenLMK105BJ104KV-F 43 each CS-079PSCAP CER 1UF 6.3V 10% X5R 0402 1uF 0402 C7 C8 C28 Digikey587-1231-2-NDTaiyo YudenJMK105BJ105KV-F 57 each CS-025PSCAP CER 10000PF 25V 10% X7R 0402 10nF C10 C12 C13 C14 C16 C17 C18 Digikey587-1223-2-NDTaiyo YudenTMK105B7103KV-F 63 each CS-024PSCAP CER 8PF 50V C0G 0402 8pF C11 C15 C23 ArrowGRM1555C1H8R0DZ01DMurata Electronics North America GRM1555C1H8R0DZ01D 75 each CS-082PSCAP CER 22PF 50V 5% NP0 0402 22pF 0402 C19 C20 C30 C32 C33 Digikey445-1239-2-NDTDK CorporationC1005C0G1H220J 83 each CS-034PSCAP 1.0PF 50V CERAMIC 0402 SMD 1.0pF 0402 C24 C25 C26 Digikey490-3199-2-NDMurata Electronics North America GRM1555C1H1R0CA01D 92 each JP-086PSCONN HEADER FEMALE 2x6 1.27MM SMT 2x6 Lo Profile J1 J2 Wafe Hardware Electronics2321-206MG0CUN01Wafe Hardware Electronics2321-206MG0CUN01 102 each IN-006PSFILTER CHIP 1000 OHM 250MA 0402 BLM15HG102SN1D L1 L4 ArrowBLM15HG102SN1DMurata Electronics North America BLM15HG102SN1D 112 each IN-026PSINDUCTOR 2.7NH 850MA 0402 2.7nH 0402 L2 L3 Digikey490-1137-2-NDMurata Electronics North America LQW15AN2N7D00D Axxess Industries Inc. #103 - 470 Neave Court, Kelowna, BC V1V 2M2, Canada 1-866-680-2457 Fax 1-250-491-4715 AP-120 2Page 1 of 121 each IN-003PSINDUCTOR 3.3NH 0603 3.3nH L5 Digikey490-1104-2-NDMurata Electronics North America LQG18HN3N3S00D 131 each TS-009PSMOSFET N-CH 30V 1.7A SC70-3 AO7400 Q1 Digikey785-1084-2-NDAlpha & Omega Semiconductor Inc AO7400 141 each RS-123PSRES 10 OHM 1/10W 5% 0402 SMD 10 0402 R1 DigikeyP10JTR-NDPanasonic - ECGERJ-2GEJ100X 154 each RS-110PSRES 100K OHM 1/10W 5% 0402 SMD 100K 0402 R2 R4 R7 R9 DigikeyP100KJTR-NDPanasonic - ECGERJ-2GEJ104X 161 each RS-055PSRES 1.0 OHM 1/16W 5% 0402 SMD 1R R3 ArrowCRCW04021R00JNEDVishay/DaleCRCW04021R00JNED 172 each RS-066PSRES 2.0M OHM 1/16W 5% 0402 SMD 2M R8 R10 Digikey541-2.0MJTR-NDVishay/DaleCRCW04022M00JNED 181 each IC-090PSIC RF TXRX ZIGBEE 192KB 48QFN EM357-RTR U1 EmberEM357-RTREmberEM357-RTR 191 each IC-101PSIC FLASH 2MBIT 66MHZ 8SOIC AT45DB021D-SSH-B U2 DigikeyAT45DB021D-SSH-B-NDAtmelAT45DB021D-SSH-B 201 each CR-016PSCRYSTAL 24.000 MHZ 18PF SMD SJK-7U-24.000-18-10-60-C-25 Y1 SHENZHEN CRYSTAL TECHNOLOGY INDUSTRIAL CO.,LTD. SJK-7U-24.000-18-10-60- C-25 SHENZHEN CRYSTAL TECHNOLOGY INDUSTRIAL CO.,LTD. SJK-7U-24.000-18-10-60-C -25 211 each CB-112PSPCB, LPZM301 LPZM301 Chinapcbone Technology LimitedLPZM301Chinapcbone Technology Limited LPZM301 221 each MT-003PSRF SHIELD, 2.4GHz, XPZM3 RF SHIELD XPZM3 Dongguan Bosi Metal & Electronic Co, Ltd. MT-003Dongguan Bosi Metal & Electronic Co, Ltd. MT-003 Parts List AP-120 ItemQtyPart NumberTypeTitleReference Printed 4/15/2013 Rev 1 VendorVendor P/NMfr NameMfr P/N Assembly, PCB, LPZM3 LPZM3 UnitRevDetail Axxess Industries Inc. #103 - 470 Neave Court, Kelowna, BC V1V 2M2, Canada 1-866-680-2457 Fax 1-250-491-4715 AP-120 2Page 2 of

Island Compliance Services Inc. Axxess Industries Inc. Report Number: 0225A Model: LPZM3 Page | 1 of 2 Island Compliance Services Inc. RF Exposure Evaluation Report Prepared for: Axxess Industries Inc. Unit 103-470 Neave Court Kelowna BC, V1V 2M2 Canada Equipment Under Test (EUT): Model: LPZM3 FCC ID: WP4LPZM3 IC Certification number: 9709A-LPZM3 FCC Rule Part(s): Part 15B, 15C Industry Canada Rule Part(s) RSS-210 Tested by: Island Compliance Services Inc. 6454 Fitzgerald Road Courtenay, BC V9J 1N7 Authorized By Andrew Eadie (Manager) Date: 28 th May 2013 FCC OATS registration number: 386117 Industry Canada OATS registration number: 9578B-1 Island Compliance Services Inc. Axxess Industries Inc. Report Number: 0225A Model: LPZM3 Page | 2 of 2 Island Compliance Services Inc. 1.1 RF EXPOSURE EVALUATION FCC 1.1310 states the criteria listed in the table below shall be used to evaluate the environmental impact of human exposure to radiofrequency (RF) radiation as specified in Section 1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of Section 2.1093. Further information on evaluating compliance with these limits can be found in the FCC's OST/OET Bulletin Number 65, “Evaluating Compliance with FCC-Specified Guidelines for Human Exposure to Radiofrequency Radiation”. Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (s) (A) Limits for Occupational/Control Exposures 300-1500 - - F/300 6 1500-100,000 - - 5 6 (B) Limits for General Population/Uncontrolled Exposures 300-1500 - - F/1500 6 1500-100,000 - - 1 30 TABLE 1 - POWER DENSITY LIMITS 1.2 EUT OPERATING CONDITION Maximum antenna gain = 4 dBi (nom) 1.3 RF EXPOSURE EVALUATION DISTANCE CALCULATION Frequency (MHz) Conducted Output Power (dBm) Max Antenna Gain (dBi) Max EIRP (W) Power Density Limit (mW/cm 2 ) R (cm) 2.405 -10.12 4.0 0.00024 1 0.13 2.440 -11.40 4.0 0.00018 1 0.12 2.480 -12.80 4.0 0.00005 1 0.06 TABLE 2 - DISTANCE CALCULATIONS where: S = Allowable Power density Limit (mW/cm 2 ) EIRP = Equivalent (or effective) isotropically radiated power (mW) R = Distance to the center of radiation of the antenna (cm) As shown above, the minimum distance where the MPE limit is reached is 0.13 cm from the EUT with 4.0 dBi antenna.
=  
 4. .

Island Compliance Services Inc. Axxess Industries Inc. Report Number: 0225A Model: LPZM3 Page | 1 of 29 Island Compliance Services Inc. MEASUREMENT AND TEST REPORT VERSION 1.00 Report Prepared for: Axxess Industries Inc. Unit 103-470 Neave Court Kelowna BC, V1V 2M2 Canada Equipment Under Test (EUT): Model: LPZM3 FCC ID: WP4LPZM3 IC Certification number: 9709A-LPZM3 FCC Rule Part(s): Part 15B, 15C Industry Canada Rule Part(s) RSS-210 Tested by: Island Compliance Services Inc. 6454 Fitzgerald Road Courtenay, BC V9J 1N7 Prepared By Authorized By A. Horel (Technical Writer) A. Eadie (Sr. EMC Eng.) Note: This test report has been prepared for the Applicant and device described herein. It may not be duplicated or used in part without prior written consent from Island Compliance Services Inc. FCC OATS registration number: 386117 Industry Canada OATS registration number: 9578B-1 Island Compliance Services Inc. Axxess Industries Inc. Report Number: 0225A Model: LPZM3 Page | 2 of 29 Island Compliance Services Inc. Revision History Version Date Author Comment 1.0 28/05/2013 A. Horel Original Release Island Compliance Services Inc. Axxess Industries Inc. Report Number: 0225A Model: LPZM3 Page | 3 of 29 Island Compliance Services Inc. 1.1 CONTENTS 1.1 Contents ................................................................................................................................................ 3 2 Summary of Test Results ............................................................................................................................... 5 2.1 Environmental Conditions ...................................................................................................................... 5 2.2 Standard Test Conditions and Engineering Practices ............................................................................... 6 3 General Equipment Specifications ................................................................................................................. 7 3.1 Auxiliary Equipment ............................................................................................................................... 7 3.2 Engineering Changes to Production Unit ................................................................................................ 7 4 RF Peak Power Output................................................................................................................................... 8 4.1 Test Method .......................................................................................................................................... 8 4.2 Data ...................................................................................................................................................... 8 4.3 Plot(s) .................................................................................................................................................... 8 4.4 Additional Information........................................................................................................................... 9 5 Occupied Bandwidth ................................................................................................................................... 10 5.1 Test Method ........................................................................................................................................ 10 5.2 Data .................................................................................................................................................... 10 5.3 Plots .................................................................................................................................................... 10 5.4 Additional Information......................................................................................................................... 11 6 Power Spectral Density................................................................................................................................ 12 6.1 Test Method ........................................................................................................................................ 12 6.2 Limits................................................................................................................................................... 12 6.3 Data .................................................................................................................................................... 12 6.4 Plots .................................................................................................................................................... 12 6.5 Additional Information......................................................................................................................... 13 7 Conducted Spurious Emissions .................................................................................................................... 14 7.1 Test Method ........................................................................................................................................ 14 7.2 Limits................................................................................................................................................... 14 7.3 Data .................................................................................................................................................... 14 7.4 Plots .................................................................................................................................................... 15 7.5 Additional Information......................................................................................................................... 16 8 Conducted Spurious Emissions Bandedge .................................................................................................... 17 8.1 Test Method ......................................................................…

Text truncated - open the document above for the full version.

Island Compliance Services Inc. Axxess Industries Inc. Model: LPZM3 Page | 1 of 1 Island Compliance Services Inc. Test Set up Photographs Model LPZM3