X5B-PL6322AFTERGLOW PS3 WIRELESS CONTROLLER

Thank you for purchasing the Game Stop wireless controller for the PLAYSTATION 3 video game system. Contents: 1 AFTERGLOW PS3 WIRELESS CONTROLLER 1 USB Dongle (found attached to the controller) 1 USB Cable 1 Manual Set up: 1) Remove the USB receiver that is attached to the bottom of the controller and plug it into one of the free ports of your PLAYSTATION 3 2) USB receiver LED will flash rapidly while looking for positive connection with the controller. USB receiver light will light up solid when the connection is established 3) Place the power switch is in “ON” position 4) Press the “HOME” button, the controller will be automatically assigned a player number. (you can change the controller player number by pressing and holding the HOME button and then changing the player number from the PS3 menu – refer to your console manual for more information 5) The battery of the controller is low when its LED start flashing. Power Save Mode: Controller will go into Power Save Mode after 3 (three) minutes of inactivity. You need to press the START button to turn it back to the ACTIVE mode Important Notice 1. Recommended user age range 14+. 2. Adult supervision is necessary when controller is used by child CAUTION: Changes or modifications to this equipment not expressly approved by the manufacturer could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC ID for Controller: X5B-PL6322 FCC ID for Dongle: X5B-BB6308A This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. © 2010 Performance Designed Products LLC. All rights reserved. PDP and AFTERGLOW™ are trademarks of Performance Designed Products LLC. PlayStation 3® is a registered trademark of Sony Computer Entertainment, Inc. This product is not designed, manufactured, sponsored or endorsed by Sony Computer Entertainment. Please keep this information for future reference.

Neutron Engineering Inc. Project No.: 1104C097 Page 2 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 2 of 14 1104C097 1104C097

AP.2 for PS3 Model: PL-6322 FCC ID: X5B-PL6322

Neutron Engineering Inc. Project No.: 1104C097 Page 3 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 3 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 4 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 4 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 5 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 5 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 6 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 6 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 7 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 7 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 8 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 8 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 9 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 9 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 10 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 10 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 11 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 11 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 12 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 12 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 13 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 13 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 14 of 14 1104C097 1104C097 Neutron Engineering Inc. Project No.: 1104C097 Page 14 of 14 1104C097 1104C097

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 2 of 64 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 3 of 64 Table of Contents Page 1 . CERTIFICATION 6 2 . SUMMARY OF TEST RESULTS 7 2.1 TEST FACILITY 8 2.2 MEASUREMENT UNCERTAINTY 8 3 . GENERAL INFORMATION 9 3.1 GENERAL DESCRIPTION OF EUT 9 3.2 DESCRIPTION OF TEST MODES 12 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 12 3.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 13 3.5 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 14 4 . EMC EMISSION TEST 15 4.1 CONDUCTED EMISSION MEASUREMENT 15 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 15 4.1.2 MEASUREMENT INSTRUMENTS LIST AND SETTING 15 4.1.3 TEST PROCEDURE 16 4.1.4 DEVIATION FROM TEST STANDARD 16 4.1.5 TEST SETUP 16 4.1.6 EUT OPERATING CONDITIONS 17 4.1.7 TEST RESULTS 18 4.2 RADIATED EMISSION MEASUREMENT 20 4.2.1 RADIATED EMISSION LIMITS 20 4.2.2 MEASUREMENT INSTRUMENTS LIST ANS SETTING 21 4.2.3 TEST PROCEDURE 23 4.2.4 DEVIATION FROM TEST STANDARD 23 4.2.5 TEST SETUP 24 4.2.6 EUT OPERATING CONDITIONS 25 4.2.7 TEST RESULTS (BELOW 30MHZ) 26 4.2.8 TEST RESULTS (BETWEEN30 – 1000 MHZ) 27 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 29 5 . NUMBER OF HOPPING CHANNEL 41 5.1 APPLIED PROCEDURES / LIMIT 41 5.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 41 5.1.2 TEST PROCEDURE 41 5.1.3 DEVIATION FROM STANDARD 41 5.1.4 TEST SETUP 41 5.1.5 EUT OPERATION CONDITIONS 41 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 4 of 64 Table of Contents Page 5.1.6 TEST RESULTS 42 6 . AVERAGE TIME OF OCCUPANCY 43 6.1 APPLIED PROCEDURES / LIMIT 43 6.1.1 MEASUREMENT INSTRUMENTS LIST 43 6.1.2. TEST PROCEDURES 43 6.1.3. TEST SETUP LAYOUT 43 6.1.4. TEST DEVIATION 43 6.1.5. EUT OPERATION DURING TEST 43 6.1.6. TEST RESULTS 44 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 46 7.1 APPLIED PROCEDURES / LIMIT 46 7.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 46 7.1.2 TEST PROCEDURE 46 7.1.3 DEVIATION FROM STANDARD 46 7.1.4 TEST SETUP 46 7.1.5 EUT OPERATION CONDITIONS 46 7.1.6 TEST RESULTS 47 8 . BANDWIDTH TEST 48 8.1 APPLIED PROCEDURES / LIMIT 48 8.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 48 8.1.2 TEST PROCEDURE 48 8.1.3 DEVIATION FROM STANDARD 48 8.1.4 TEST SETUP 48 8.1.5 EUT OPERATION CONDITIONS 48 8.1.6 TEST RESULTS 49 9 . PEAK OUTPUT POWER TEST 51 9.1 APPLIED PROCEDURES / LIMIT 51 9.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 51 9.1.2 TEST PROCEDURE 51 9.1.3 DEVIATION FROM STANDARD 51 9.1.4 TEST SETUP 51 9.1.5 EUT OPERATION CONDITIONS 51 9.1.6 TEST RESULTS 52 10 . ANTENNA CONDUCTED SPURIOUS EMISSION 54 10.1 APPLIED PROCEDURES / LIMIT 54 10.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 54 10.1.2 TEST PROCEDURE 54 10.1.3 DEVIATION FROM STANDARD 54 10.1.4 TEST SETUP 54 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 5 of 64 Table of Contents Page 10.1.5 EUT OPERATION CONDITIONS 54 10.1.6 TEST RESULTS 55 11 . EUT TEST PHOTO 61 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 6 of 64 1. CERTIFICATION E q u i p m e n t : AFTERGLOW PS3 WIRELESS CONTROLLER Trade Name AFTERGLOW Model Name. PL-6322 A p p l i c a n t : Performance Designed Products,LLC Date of Test: Apr. 13, 2011 ~ Apr. 29, 2011 T e s t I t e m : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.247) / ANSI C63.4 : 2003 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuration contained in our test report (Ref No. NEI-FCCP-1-1104C097) were obtained utilizing the test procedures, test instruments, test sites that has been accredited by the Authority of NVLAP and TAF according to the ISO-17025 quality assessment standard and technical standard(s). Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 7 of 64 2. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.247) , Subpart C Standard Section Test Item Judgment Remark 15.207 Conducted Emission PASS 15.247(d) Antenna conducted Spurious EmissionPASS 15.247 (a)(1) Hopping Channel Separation PASS 15.247 (b)(1) Peak Output Power PASS 15.247(d)/15/209 Radiated Spurious Emission PASS 15.247 (a)(1)(iii) Number of Hopping Frequency PASS 15.247 (a)(1)(iii) Dwell Time PASS 15.205 Restricted Bands PASS 15.203 Antenna Requirement PASS 1.1307 1.1310 2.1091 2.1093 RF Exposure Compliance PASS NOTE: (1)” N/A” denotes test is not applicable in this Test Report Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 61 of 64 11. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 61 of 64 11. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 62 of 64 Radiated Measurement Photos 9K~30MHz Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 62 of 64 Radiated Measurement Photos 9K~30MHz Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 63 of 64 Radiated Measurement Photos 30M~1000MHz Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 63 of 64 Radiated Measurement Photos 30M~1000MHz Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 64 of 64 Radiated Measurement Photos Above 1000MHz Neutron Engineering Inc. Report No.: NEI-FCCP-1-1104C097 Page 64 of 64 Radiated Measurement Photos Above 1000MHz