XBBHSM-SHIFTWireless ergonomic Bluetooth mouse

“Hereby, Hippus N.V. declares that the radio equipment HSM shift is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://handshoemouse.com ". Frequency: 2.4 GHz Power output 4.2 dBm FCC id: XBBHSM-SHIFT 1-This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any unauthorized changes or modifications to this equipment would void the user’s authority to operate this device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC: 10466A-HSMSHIFT 2- IC statement: This device complies with Industry Canada ICES-003. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de l’utilisateur pour actionner cet équipement.

CHECK THE CONTENTS OF THE BOX • HandshoeMouse Shift • USB A-C (charger) cable • Protective pouch RIGHT-HAND VIEW LEFT-HAND VIEW INSTALLATION AND CHARGING INSTRUCTIONS The HandshoeMouse can be operated wireless via Bluetooth or wired using USB. To establish communication between the mouse and PC/Laptop, follow these instructions: Select orientation by pressing the left-right button (A) Switch on the mouse (A) Press the Bluetooth button for 5 seconds (B) Select button priority with the L/R switch (C) Choose Bluetooth, Mice, keyboards, pens etc. and select HSMshift When the LED starts flashing red: Recharge! To recharge, connect the USB cable A LED light will start flashing blue Go to Microsoft settings, select Bluetooth & other devices Add Bluetooth or other device Follow these steps to install and enjoy your HandshoeMouse. This mouse allows you to work both right - or left handed. IF THE CURSOR DOES NOT MOVE FOLLOW THIS PROCEDURE: 1. Connect the mouse to the computer with the USB cable, to charge the mouse battery. 2. After charging for several hours, disconnect the USB cable from the mouse. Switch on the mouse. 3. When the mouse shows a blue light, follow the pairing procedure described above. 4. If the problem persists visit: https://handshoemouse.com/faq or contact: [email protected] FOR WIRED OPERATION, JUST PLUG IN THE USB CABLE AND YOUR MOUSE WILL BE READY TO USE. Once your mouse is connected to your PC / laptop, you can start using it. To work in comfort, set the cursor speed to medium. 1. 4. 2. 5. 3. 6. (B) (C) (A) (A) AB Sit in a relaxed position, place your hand on the mouse and your forearm on the desk. For further information and images on ‘Do’s and Don’ts’ have a look at ‘TIPS’ on the HandshoeMouse site. https://handshoemouse.com/tips Finger tips may just very lightly touch the desktop As a rule, a HandshoeMouse should be moved from the forearm, not from the shoulder. To operate within minute areas on the screen, one may, of course, move from the wrist Do not lift your elbow Relax your fingers Too large Too small If your cursor speed is too high, this may result in unnecessary muscle tension as you try to control the cursor movement. Therefore, we advise you to set your cursor speed to medium. Set your cursor (pointer) speed to medium, (under Microsoft): 1. select ‘Settings’ 2. select ‘Devices’ 3. click ‘Mouse’ 4. click ‘Additional mouse options’ 5. select ‘Pointer Options’ 6. under Motion, set your pointer speed INSTRUCTIONS FOR OPTIMAL COMFORT To experience maximum comfort and prevent muscle strain in neck and shoulders: ensure that hand and arm are relaxed and fully supported. The HandshoeMouse Shift gives you maximum flexibility. It allows you to shift from right to left handed use, reducing muscle strain whenever necessary. By means of the shift function you can select the orientation that suits you best. 3 YEAR WARRANTY For more information refer to Hippus NV. https://handshoemouse.com/faq If you follow the above instructions, you will certainly experience the advantages of the ergonomic design of the HandshoeMouse.

FCC, Request for non-disclosure Date: 21-Nov-2018 RF_501, Issue 8 Page 1 of 1 Company Name: Hippus N.V. Address: Stationsstraat 1 K City: Roelof arendsveen Country: Netherlands To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request f or conf identiality FCC ID: XBBHSM-SHIFT Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and conf idential treatment of the f ollowing materials submitted in support of FCC certif ication application: x Bill(s) of Material x Block Diagrams x Operational Description x Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical inf ormation, which would customarily be guarded f rom competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustif ied benef its for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Conf idential treatment of the f ollowing materials (See notes below): x Internal Photos x User’s Manual x Test Set-up Photos x External Photos Justif ication: In view of ongoing evaluations prior to market introduction it is requested that the above mentioned is confidential. Date 12-10-2020 Name and signature of applicant: Sjoerd Eisma Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! The planned date should stated in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Page 1 of 3 External Photo Module Product name : Wireless ergonomic Bluetooth mouse small size Applicant : Hippus N.V. FCC ID : XBBHSM-SHIFT IC ID : 10466A-HSMSHIFT Test report No. 200500625 001 Test report No. 200500625 001 Page 1 of 3 Table of Contents 1 External Photos ....................................................................................................................................... 2 Top view .............................................................................................................................................................. 2 Bottom view ........................................................................................................................................................ 2 Labelling .............................................................................................................................................................. 3 Test report No. 200500625 001 Page 2 of 3 1 External Photos Top view Bottom view Test report No. 200500625 001 Page 3 of 3 Labelling

on R L LARGE xxxx xxxx Hippus N.V. Stationstraat 1-k 2371 SH Roelofarendsveen Netherlands Product: HSM+ Revision: 4 Date: 26-06-2020 Black RAL9005 PTFE Dark grey PMS 432 C Matte ABS MT K7000G Optic black PMMA SPI A-2 and K5024G Dark grey PMS 432 C Matte ABS MT K5024G Dark grey PMS 432 C Gloss ABS SPI A-2 Light grey PMS 428C Matte ABS MT K7000G HSMshift-L IC:10466A-HSMSHIFT Model: HSM shift L HSM shift MHSM shift S

on R L LARGE xxxx xxxx Hippus N.V. Stationstraat 1-k 2371 SH Roelofarendsveen Netherlands Product: HSM+ Revision: 4 Date: 26-06-2020 Black RAL9005 PTFE Dark grey PMS 432 C Matte ABS MT K7000G Optic black PMMA SPI A-2 and K5024G Dark grey PMS 432 C Matte ABS MT K5024G Dark grey PMS 432 C Gloss ABS SPI A-2 Light grey PMS 428C Matte ABS MT K7000G HSMshift-L IC:10466A-HSMSHIFT Model: HSM shift L HSM shift MHSM shift S

Page 1 of 4 Internal Photo Module Product name : Wireless ergonomic Bluetooth mouse small size Applicant : Hippus N.V. FCC ID : XBBHSM-SHIFT IC ID : 10466A-HSMSHIFT Test report No. 200500625 001 Test report No. 200500625 001 Page 1 of 4 Table of Contents 1 Internal Photos ........................................................................................................................................ 2 Assembly (mainboard, switch board, battery) .................................................................................................... 2 Main board (bottom) .......................................................................................................................................... 2 Main board (Top) ................................................................................................................................................ 3 Switch board (top)............................................................................................................................................... 3 Switch board (bottom) ........................................................................................................................................ 4 Test report No. 200500625 001 Page 2 of 4 1 Internal Photos Assembly (mainboard, switch board, battery) Main board (bottom)

Test report No. 200500625 001 Page 3 of 4 Main board (Top) Switch board (top) Test report No. 200500625 001 Page 4 of 4 Switch board (bottom)

Page 1 of 5 FCC SAR Exclusion Report Product name : Wireless ergonomic Bluetooth mouse small size Applicant : Hippus N.V. FCC ID : XBBHSM-SHIFT IC ID : 10466A-HSM-SHIFT Test report No. : 200500625 005 V1.00 Report number: 200500625 005 V1.00 Page 1 of 5 Laboratory information Accreditation Telefication complies with the accreditation criteria for test laboratories as laid down in ISO/IEC 17025:2017. The accreditation covers the quality system of the laboratory as well as the specific activities as described in the authorized annex bearing the accreditation number L021 and is granted on 30 November 1990 by the Dutch Council For Accreditation (RvA: Raad voor Accreditatie). Telefication is designated by the FCC as an Accredited Test Firm for compliance testing of equipment subject to Certification under Parts 15 & 18. The Designation number is: NL0001. Telefication is a Wireless Device Testing laboratory recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements. The Industry Canada registration number for the 3 meter test chamber of Telefication is: 4173A-1. Telefication is a registered Conformity Assessment body (CAB) under the Japan-EC MRA (Agreement on Mutual Recognition between Japan and the European Community). The registration number is: 201. Documentation The test report must always be reproduced in full; reproduction of an excerpt only is subject to written approval of the testing laboratory. The documentation of the testing performed on the tested devices is archived for 10 years at Telefication Netherlands. Testing Location Test Site Telefication BV Test Site location Edisonstraat 12a 6902 PK Zevenaar The Netherlands Tel. +31889983600 Fax. +31316583189 Report number: 200500625 005 V1.00 Page 2 of 5 Revision History Version Date Remarks By v1.00 05-03-2021 Release version PS Report number: 200500625 005 V1.00 Page 3 of 5 Table of Contents Revision History .............................................................................................................................................. 2 1 General Description ................................................................................................................................. 4 1.1 Applicant ................................................................................................................................................ 4 1.2 Manufacturer ........................................................................................................................................ 4 1.3 Tested Equipment Under Test (EUT) ..................................................................................................... 4 1.4 SAR Measurement Evaluation ............................................................................................................... 5 1.4.1 Maximum Output Power ................................................................................................................... 5 1.4.2 SAR Testing Exclusions ...................................................................................................................... 5 1.5 Summary ................................................................................................................................................ 5 Report number: 200500625 005 V1.00 Page 4 of 5 1 General Description 1.1 Applicant Client name: Hippus N.V. Address: Stationsstraat 1K Zip code: 2371 SH Roelofarendsveen Telephone: +44 1872 562-715 E-mail: [email protected] Contact name: Sjoerd Eisma 1.2 Manufacturer Manufacturer name: Hippus N.V. Address: Stationsstraat 1K Zip code: 2371 SH Roelofarendsveen Telephone: +44 1872 562-715 E-mail: [email protected] Contact name: Sjoerd Eisma 1.3 Tested Equipment Under Test (EUT) Product name: Wireless ergonomic Bluetooth mouse small size Brand name: HandshoeMouse Product type: 2.4 GHz wideband data transmission equipment FCC ID: XBBHSM-SHIFT IC ID: 10466A-HSM-SHIFT Model(s): ShiftHSMs+, ShiftHSMm+, ShiftHSMl+ Software version: -- Hardware version: -- Report number: 200500625 005 V1.00 Page 5 of 5 1.4 SAR Measurement Evaluation 1.4.1 Maximum Output Power The maximum radiated power including tune-up tolerance is shown as below. Technology Max power level (dBm) BLE -8.56* * from Telefication report 200500625 001 V1.00 1.4.2 SAR Testing Exclusions According to KDB 447498 D01, the SAR test exclusion condition is based on source-based time-averaged maximum conducted output power, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions. The SAR exclusion threshold is determined by the following formula. 1. For the test separation distance <= 50 mm When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. 2. For the test separation distance > 50 mm, and the frequency at 100 MHz to 1500 MHz 3. For the test separation distance > 50 mm, and the frequency at > 1500 MHz to 6 GHz Mode Max. Tune- up Power (dBm) Max. Tune- up Power (mW) Ant. to Surface (mm) Calculated Result Require SAR Testing? BLE -8.56 0.14 10 0.022 No Note: 1. When separation distance <= 50 mm and the calculated result shown in above table is <= 3.0, the SAR testing exclusion is applied. 2. When separation distance > 50 mm and the device output power is less than the calculated result (power threshold, mW) shown in above table, the SAR testing exclusion is applied. 1.5 Summary Considering the SAR test exclusion conditions per KDB 447498, SAR testing for this device is not required.

FCC and IC Test report for parts 15.207, 15.209, 15.247, RSS-247, RSS-Gen Product name : Wireless ergonomic Bluetooth mouse small size Applicant : Hippus N.V. FCC ID : XBBHSM-SHIFT IC ID : 10466A-HSMSHIFT Test report No. : 200500625 001 V1.10 Report number: 200500625 001 V1.10 Page 1 of 32 Laboratory information Accreditation Telefication complies with the accreditation criteria for test laboratories as laid down in ISO/IEC 17025:2017. The accreditation covers the quality system of the laboratory as well as the specific activities as described in the authorized annex bearing the accreditation number L021 and is granted on 30 November 1990 by the Dutch Council For Accreditation (RvA: Raad voor Accreditatie). Telefication is designated by the FCC as an Accredited Test Firm for compliance testing of equipment subject to Certification under Parts 15 & 18. The Designation number is: NL0001. Telefication is a Wireless Device Testing laboratory recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements. The Industry Canada registration number for the 3 meter test chamber of Telefication is: 4173A-1. Telefication is a registered Conformity Assessment body (CAB) under the Japan-EC MRA (Agreement on Mutual Recognition between Japan and the European Community). The registration number is: 201. Documentation The test report must always be reproduced in full; reproduction of an excerpt only is subject to written approval of the testing laboratory. The documentation of the testing performed on the tested devices is archived for 10 years at Telefication Netherlands. Testing Location Test Site Telefication BV Test Site location Edisonstraat 12a 6902 PK Zevenaar The Netherlands Tel. +31316583180 Fax. +31316583189 Test Site FCC NL0001 Report number: 200500625 001 V1.10 Page 2 of 32 Revision History Version Date Remarks By v0.50 1-10-2020 First draft PS v1.00 7-10-2020 Initial issue PS V1.10 23-03-2021 Second issue • Second dash in IC ID removed PS Report number: 200500625 001 V1.10 Page 3 of 32 Table of Contents Revision History .............................................................................................................................................. 2 Summary of Test results .................................................................................................................................. 5 1 General Description ................................................................................................................................. 6 1.1 Applicant ................................................................................................................................................ 6 1.2 Manufacturer ........................................................................................................................................ 6 1.3 Tested Equipment Under Test (EUT) ..................................................................................................... 6 1.4 Product specifications of Equipment under test ................................................................................... 7 1.5 Environmental conditions...................................................................................................................... 7 1.6 Measurement standards ....................................................................................................................... 7 1.7 Applicable standards ............................................................................................................................. 7 1.8 Observation and remarks ...................................................................................................................... 7 1.9 Conclusions ............................................................................................................................................ 8 2 Test configuration of the Equipment Under Test ..................................................................................... 9 2.1 Test mode .............................................................................................................................................. 9 2.2 Test setups ............................................................................................................................................. 9 2.3 Equipment used in the test configuration ........................................................................................... 10 3 Test results ............................................................................................................................................ 11 3.1 Radiated spurious emissions ............................................................................................................... 11 3.1.1 Limit ................................................................................................................................................. 11 3.1.2 Measurement instruments ............................................................................................................. 11 3.1.3 Test setup ........................................................................................................................................ 11 3.1.4 Test procedure ................................................................................................................................ 11 3.1.5 Measurement Uncertainty .............................................................................................................. 11 3.1.6 Plots of the Radiated Spurious Emissions Measurement ................................................................ 12 3.2 6dB bandwidth Measurement ............................................................................................................. 21 3.2.1 Limit .................................................................................................................................................…

Text truncated - open the document above for the full version.

Page 1 of 3 Test Setup Photo Module Product name : Wireless ergonomic Bluetooth mouse small size Applicant : Hippus N.V. FCC ID : XBBHSM-SHIFT IC ID : 10466A-HSMSHIFT Test report No. 200500625 Test report No. 200500625 Page 1 of 3 Contents 1 Test Setup Photos .................................................................................................................................... 2 1.1 Radiated emissions measurement 0.03 – 1 GHz ................................................................................... 2 1.2 Radiated emissions measurement 1 – 18 GHz ...................................................................................... 2 1.3 EUT on test table ................................................................................................................................... 3 1.4 Conducted emissions (computer peripheral) ........................................................................................ 3 Test report No. 200500625 Page 2 of 3 1 Test Setup Photos 1.1 Radiated emissions measurement 0.03 – 1 GHz 1.2 Radiated emissions measurement 1 – 18 GHz Test report No. 200500625 Page 3 of 3 1.3 EUT on test table 1.4 Conducted emissions (computer peripheral)