XDE-RFA201RFK200

RFK200 Size: 4” x 10.5” / folded size: 1.75” x 2” staubitz design associates date: 10.30.09/rev: 11.03.09/revB: 11.12.09/revC: 11.19.09 Westek RFK200 Instruction Sheet I09-0097-A fold fold fold fold fold fold Wireless Door Chime Kit This kit allows the homeowner to choose from 16 different tunes including various classical music, holiday jingles, and happy birthday. Transmitter Mounting Instructions: 1. Detach back panel by sliding screwdriver under slot on corner. 2. Mount back panel with screws provided. 3. Reattach unit to back panel by snapping it into place. 4. Unit can also be mounted with double faced tape, included. 5. Unit is weather resistant for outdoor use. Battery Replacement for Transmitter: 1. Detach back panel by sliding screwdriver under slot on corner. 2. Replace battery with 23A 12V alkaline battery. 3. Reattach unit to back panel by snapping it into place. Unit Operating Instructions: 1. Plug receiver into any standard outlet. 2. Mount transmitter in desired location. 3. Press button on transmitter to ring doorbell. 4. To change the ring, press the center button on the bottom of the receiver until you reach the desired tune. 5. Volume down button is located to the left, volume up button is located on the right. 6. Should your doorbell ring without the transmitter button being pressed, it may be detecting a signal from a neighboring device. In this case, simply choose a different channel code. Transmitter and receiver must have the same code selected in order to function properly. (To change channel, select A, B, C, or D on the back of the receiver. Detach back panel of transmitter by sliding screwdriver under slot on either side of unit. Select the same letter as the receiver (A, B, C, or D). Reattach back panel.) Note: Before operating the first time, remove protective plastic battery tab inside transmitter. Kit de carillon de porte sans fil Ce kit permet au propriétaire de choisir parmi 16 mélodies différentes, notamment de musique classique, de refrains de fête et de joyeux anniversaire. Instructions de montage de l’émetteur : 1. Séparer le panneau arrière en glissant un tournevis sous la fente du coin. 2. Monter le panneau arrière avec les vis fournies. 3. Remettre l’appareil en place sur le panneau arrière en l’enclenchant. 4. L’appareil peut également être monté au moyen du ruban adhésif à double face inclus. 5. L’appareil est résistant aux intempéries et utilisable à l’extérieur. Remplacement de la pile de l’émetteur : 1. Séparer le panneau arrière en glissant un tournevis sous la fente du coin. 2. Remplacer la pile par une pile alcaline 23A 12 V. 3. Remettre l’appareil en place sur le panneau arrière en l’enclenchant. Instructions d’utilisation : 1. Brancher le récepteur sur une prise standard. 2. Monter l’émetteur à l’emplacement souhaité. 3. Appuyer sur le bouton de l’émetteur pour faire sonner. 4. Pour changer de mélodie, appuyer sur le bouton central au bas du récepteur jusqu’à obtenir la mélodie souhaitée. 5. Le bouton gauche sert à baisser le volume, le bouton droit sert à augmenter le volume. 6.Si la sonnette se déclenche sans appuyer sur le bouton de l’émetteur, il se peut qu’un signal de dispositif avoisinant soit détecté. Dans ce cas, il suffit de choisir un code de canal différent. Le même code doit être sélectionné pour l’émetteur et le récepteur afin d’assurer un fonctionnement adéquat. (Pour changer de canal, sélectionner A, B, C ou D à l’arrière du récepteur. Séparer le panneau arrière de l’émetteur en glissant un tournevis sous la fente d’un des côtés de l’appareil. Sélectionner la lettre correspondant à celle du canal du récepteur (A, B, C, ou D) et remettre en place sur le panneau arrière de l’appareil.) Remarque : Avant de faire fonctionner l’appareil pour la première fois, retirer la languette en plastique de protection de la pile à l’intérieur de l’émetteur. Juego de timbre inalámbrico para puertas Este juego le permite al propietario del hogar elegir de entre 16 melodías diferentes, incluyendo varias de música clásica, canciones populares de días festivos, y cumpleaños. Instrucciones de montaje del transmisor: 1.Deslice un destornillador debajo de la ranura en la esquina y retire el panel trasero. 2. Monte el panel trasero con los tornillos suministrados. 3. Reinstale la unidad en el panel trasero, fijándola a presión en su posición. 4. La unidad también puede montarse con la cinta de doble cara incluida. 5. La unidad es resistente a la intemperie, para uso en exteriores. Reemplazo de la batería para el transmisor: 1.Deslice un destornillador debajo de la ranura en la esquina y retire el panel trasero. 2. Reemplace la batería con una batería alcalina de 23A 12V. 3. Reinstale la unidad en el panel trasero, fijándola a presión en su posición. Instrucciones de operación de la unidad: 1. Enchufe el receptor en cualquier tomacorriente estándar. 2. Monte el transmisor en el lugar deseado. 3. Oprima el botón en el transmisor para hacer sonar el timbre de puerta. 4. Para cambiar el sonido del timbre, oprima el botón central en la parte inferior del receptor hasta que llegue a la melodía (o tono) deseado. 5. El botón para bajar el volumen se encuentra en el lado izquierdo y el botón para subir el volumen se encuentra en el lado derecho. 6. Si el timbre de puerta suena sin que se haya oprimido el botón del transmisor, podría estar detectando la señal del dispositivo de un vecino. En este caso, sencillamente seleccione un código de canal diferente. Debe seleccionarse el mismo código para el transmisor y el receptor de modo que puedan funcionar correctamente. (Para cambiar el canal, seleccione A, B, C o D en la parte posterior del receptor. Deslice un destornillador debajo de la ranura en cualquiera de los dos lados de la unidad y retire el panel trasero del transmisor. Seleccione la misma letra usada en el receptor (A, B, C o D) y reinstálelo en la parte posterior de la unidad.) Aviso: Antes de usarlo por primera vez, retire la lengüeta protectora d…

Text truncated - open the document above for the full version.

American Tack&Hardware Co., Inc. Saddle River Executive Centre One Route 17 South Saddle River, NJ07458 U.S.A November 24, 2009 Federal Communications Commission Authorization and Evaluation Division FCC ID：XDE-RFA201 Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below: 1. Block Diagram 2. Circuit Diagram 3. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application Sincerely, Name/Title: Eric Chen / Electrical Engineer Company Name: American Tack&Hardware Co., Inc. Address: Saddle River Executive Centre One Route 17 South Saddle River, NJ07458 U.S.A TEL: +86-755-33013520 FAX: +86-755-33013522 Email: [email protected] Signature:

American Tack&Hardware Co., Inc. Saddle River Executive Centre One Route 17 South Saddle River, NJ07458 U.S.A November 24, 2009 FCC ID：XDE-RFA201 Dear Sir, I hereby have entrusted the following person to be a proxy regarding application for Type Certification. Compliance Certification Services Inc. Address: No10-1, Mingkeda Logistics Park, No.18 Huanguan South RD. Guan lan Town, Baoan District, Shenzhen China Name: Aven Zhou Job Title: Supervisor Email: [email protected] I am therefore responsible for the contents of the application. Brand Name and Model Name of the specified radio equipment: Westek / RFA201 FCC ID: XDE-RFA201 Product Name: RFK200 Name/Title: Eric Chen / Electrical Engineer Company Name: American Tack&Hardware Co., Inc. Address: Saddle River Executive Centre One Route 17 South Saddle River, NJ07458 U.S.A TEL: +86-755-33013520 FAX: +86-755-33013522 Email: [email protected] Signature:

Compliance Certification Services (Shenzhen) Inc. Report No: SZ091117B02-RP FCC ID: XDE-RFA201 Date of Issue: November 23, 2009 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 22 Rev. 00 FCC 47 CFR PART 15 SUBPART C TEST REPORT For RFK200 Model: RFA201 Trade Name: Westek Prepared for American Tack&Hardware Co., Inc Saddle River Executive Centre One Route 17 South Saddle River , NJ07458 U.S.A Prepared by COMPLIANCE CERTIFICATION SERVICES (SHENZHEN) INC. No10-1, Mingkeda Logistics Park, No.18 Huanguan South RD. Guan lan Town, Baoan District, Shenzhen China TEL: 86-755-28055000 FAX: 86-755-28055221 Compliance Certification Services (Shenzhen) Inc. Report No: SZ091117B02-RP FCC ID: XDE-RFA201 Date of Issue: November 23, 2009 Page 2 Rev. 00 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION............................................................................................. 3 2. EUT DESCRIPTION .................................................................................................................... 4 3. TEST METHODOLOGY ............................................................................................................. 5 3.1 EUT CONFIGURATION............................................................................................................... 5 3.2 EUT EXERCISE.......................................................................................................................... 5 3.3 GENERAL TEST PROCEDURES................................................................................................... 5 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .............................................. 6 3.5 DESCRIPTION OF TEST MODES.................................................................................................. 6 4. INSTRUMENT CALIBRATION................................................................................................. 6 5. FACILITIES AND ACCREDITATIONS ................................................................................... 7 5.1 FACILITIES...............................................................................................................................7 5.2 EQUIPMENT.............................................................................................................................. 7 5.3 LABORATORY ACCREDITATIONS AND LISTING........................................................................ 7 6. SETUP OF EQUIPMENT UNDER TEST .................................................................................. 8 6.1 SETUP CONFIGURATION OF EUT............................................................................................... 8 6.2 SUPPORT EQUIPMENT............................................................................................................... 8 6.3 MEASUREMENT UNCERTAINTY ..................................................................................... 8 7. FCC PART 15.231 REQUIREMENTS........................................................................................ 9 7.1 20 DB BANDWIDTH ............................................................................................................. 9 7.2 LIMIT OF TRANSMISSION TIME............................................................................................... 11 7.3 DUTY CYCLE .....................................................................................................................13 7.4 RADIATED EMISSIONS............................................................................................................ 16 7.5 POWER LINE CONDUCTED EMISSIONS.................................................................................... 21 Compliance Certification Services (Shenzhen) Inc. Report No: SZ091117B02-RP FCC ID: XDE-RFA201 Date of Issue: November 23, 2009 Page 3 Rev. 00 1. TEST RESULT CERTIFICATION Applicant: American Tack&Hardware Co., Inc. Saddle River Executive Centre One Route 17 South Saddle River, NJ07458 U.S.A Manufacturer: ShenZhen Aodee Electronic Co., Ltd. Weichuang Industrial Park, Ruoma Road, Qingxi Town, Dongguan City, P.R.C. 523662 Equipment Under Test: RFK200 Trade Name: We s t e k Model: RFA201 Date of Test: November 17- 23, 2009 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.207, 15.209 and Part 15.231. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Clinton Kao/ Manager COMPLIANCE CERTIFICATION SERVICES INC. Vincent Yao/ Assistant manager COMPLIANCE CERTIFICATION SERVICES INC. Compliance Certification Services (Shenzhen) Inc. Report No: SZ091117B02-RP FCC ID: XDE-RFA201 Date of Issue: November 23, 2009 Page 4 Rev. 00 2. EUT DESCRIPTION Product RFK200 Trade Name We s t e k Model Number RFA201 Model Difference N/A Power Supply DC 12V powered by the battery Frequency Range 315.166 MHz Modulation Technique AM Antenna Designation PCB Antenna Remark: This submittal(s) (test report) is intended for FCC ID: XDE-RFA201 filing to comply with Section 15.207, 15.209 and 15.231 of the FCC Part 15, Subpart C Rules. Compliance Certification Services (Shenzhen) Inc. Report No: SZ091117B02-RP FCC ID: XDE-RFA201 Date of Issue: November 23, 2009 Page 5 Rev. 00 3. TEST METHODOLOGY The tests documente…

Text truncated - open the document above for the full version.

Reference No.: Report No.: SZ091117B02-RP FCC ID : XDE-RFA201 Page 1 / 1 PHOTOGRAPHS OF THE TEST CONFIGURATION Radiated Emissions Setup Photos