XDP-GT09010L Digital / 2.4G RF Door Entry Camera (Transmitter)

L Digital Door Entry System Instructions manual Product Features 2.4G Digital Wireless Image Communication 2 Way Wireless Sound Communication Volume Adjustable on Monitor Wireless Door Lock Release Control on Monitor Unit (accessory) Wireless Door Bell Push Button on Door Entry Camera Unit Wireless Digital Zoom Function on Door Entry Camera Unit Wireless Door Camera Motorized Panning Function on Monitor Unit LEDs on Door Entry Camera to Allow Night Viewing Battery Operated Door Camera (optional 6V power adaptor as accessory) Completed Kit contents 1 x 2.4G Wireless TFT Monitor Unit with 1GB SD card 1 x 2.4G Wireless Door Camera Unit 2 x Fixing kits and 1 x instruction manual Optional Accessories Wired or Wireless Door Lock Release Kit Tools required: Small cross head screw driver T-10 Star screw driver Number 6 masonry drill bit A large masonry drill bit (for the Door Entry Camera) Hammer drill Small hammer Pencil, ruler and spirit level Important: before you install the L Digital Door Entry System please take these things into consideration. Position the TFT Screen close to a 13 Amp socket, for the plug-in adapter Keep the TFT out of reach of small children. Choose a position for the TFT, so you can have a clear run with all the power cable. How to install the TFT Using a spirit level and rule, mark and drill 2 holes 7 cm apart using a No. 6 drill bit, then using the wall plugs and screws provided, insert the masonry plugs. Screw the fixing screws into the plugs leaving 2 mm protruding. Attach the TFT on the wall. How to install the Door Entry Camera: When fitting the Door Camera please take into account the position of the sun throughout the year, as the camera view may be affected by direct bright sunlight. Also, if powered by an adaptor, plan the route the power cable will take from the Camera to the mains socket. Using a T-10 star screw driver unscrew the wall mount bracket from the Door Entry Camera. Using the back as a template, mark and drill the 2 mounting holes on the wall. The bottom of the Camera housing should be between 1.2 and 1.4 meters from the ground. If powering the Door Camera by batteries, remove the battery door cover on the rear housing and insert 4 x AA size Batteries. Please replace the battery door on rear housing and mount the Door entry camera unit to the bracket. Using a T-10 star screw driver screw the Door Entry Camera to the wall mount bracket. In normal use, the batteries will last approximately 6 to 9 months. If powering the Door Camera by the 6V adaptor, insert the jack plug to the socket on the Door Camera. Using a T-10 star screw driver screw the Door Entry Camera to the wall mount bracket. IMPORTANT: The Door Camera has a built-in power save mode whereby, if powered by Batteries only, it will shut down into sleep mode one minute after the “Call Button” is pressed . This sleep mode will not be activated if the Camera is powered by the 6V adaptor, which means that the Door Camera will be in View Mode at all times after power-up. Note that Alkaline batteries will power the Door Camera for approx 50 days (based on 5 activations a day) whereas Lithium batteries will last for approx 90 days. How to install the wired or wireless door release (optional accessory) Please use the diagram below as a guide Please consult the I/M that comes with these items. System Operation The system is very easy to operate. When a visitor presses the CALL button on the wireless Door Camera, the electronic door bell will sound at the TFT monitor unit. Please press any buttons on the monitor and the camera view will appear on that monitor’s TFT screen (If you have a multi-camera system installed, you may need to press the CAM SELECT button on the Monitor to bring up the Door Camera view). Note that if the Door Camera is being powered by batteries only, then, after 60 seconds, the image will disappear and the Door Camera will automatically revert to its power saving sleep mode. Press the CALL button again at the Door Camera to re-establish an image on the TFT screen. If the visitor is not within the camera view, move the camera Right or Left by using the camera’s Panning control buttons. You can talk to the visitor by pressing the Monitor’s TALK button. To listen to the visitor speak, release the TALK button (make sure the volume level is correct). There is no need for the visitor to press the CALL button again to speak to you (unless the Door Camera has reverted to its power saving sleep mode, in which case the visitor should press the CALL button again). The Door Camera has built-in night view LEDs so you can see your visitor at night, although, because CCTV cameras have limited picture visibility in the dark, even with infra-red LEDs, there is a limited range of view at night. Therefore, if the image is still dark, you may want to add a separate PIR activated light above the camera to give additional background light If you have a Door Lock Release added to the system, you can let your visitor in by pressing the OPEN button on the monitor unit. Note: The TFT Monitor will also revert to its power saving mode 2 minutes after any button was last pressed. Push Button Functionality On the TFT Monitor Unit On the Door Camera Individual Buttons on the TFT Monitor On the Side of the Monitor, there is a small switch that selects Monitor Off, Power Down On or Off. If Power Down has been selected, it means the unit will power down 2 minutes after a button has last been pressed. If Power Down has not been selected, it means that the Monitor will remain constantly in View Mode, including audio from the camera in view. 1. Mode Button SD Card Inserted : In View mode, press the Mode button once to change to Playback mode or press the MODE button and hold for 3 seconds to change to Setup mode. In either case, press once again to change back to View mode No SD Card Inserted : In View mode, press the Mode button once to change to Setup mode, press once again to change back to View mode 2. Camera…

Text truncated - open the document above for the full version.

External of EUT

FCC ID Label FCC ID: XDP-GT09010 Model Number: GT09010 Made in China This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Label Location Proposed Label Location on EUT

Internal of EUT Wireless module

RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency(RF) Radiation as specified in §1.1307(b) Limits for Maximum Permissible Exposure(MPE) Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density(mW/cm 2 ) Average Time (A) Limits for Occupational/Control Exposures 300-1500 -- -- F/300 6 1500-100000 -- -- 5 6 (B) Limits for General Population/Uncontrol Exposures 300-1500 -- -- F/1500 6 1500-100000 -- -- 1 30 11.1 Friis transmission formula: Pd=(Pout*G)\(4*pi*R 2 ) Where Pd= Power density in mW/cm 2 Pout=output power to antenna in mW G= gain of antenna in linear scale Pi=3.1416 R= distance between observation point and center of the radiator in cm Pd the limit of MPE, 1mW/cm 2 . If we know the maximum gain of the antenna and total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. 11.2 Measurement Result . Antenna gain: 1 dBi Channel Channel Frequency (MHz) Output Peak power (dBm) Output Peak power (mW) Antenna Gain (dBi) Power density at 20cm (mW/ cm 2 ) Power density Limits (mW/cm 2 ) 1 2402.00 12.93 19.63 1 0.0049 1 6 2440.00 13.05 20.18 1 0.0050 1 11 2480.00 12.85 19.27 1 0.0048 1

SHENZHEN EMTEK CO., LTD. REPORT NO: ES101009016F FCC ID: XDP-GT09010 DATE: 2/11/2011 Page 1 of 36 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF L Digital / 2.4G RF Door Entry Camera (Transmitter) MODEL No.: GT09010 FCC ID: XDP-GT09010 REPORT NO: ES101009016F ISSUE DATE: February 12, 2011 Prepared for GLOBAL TECH CHINA LTD. Room 12, 14th Floor, Tower 2, Evergain Plaza, 88 Container Port Road, Kwai Chung, HongKong Prepared by SHENZHEN EMTEK CO., LTD Bldg 69, Majialong Industry Zone, Nan0shan District, Shenzhen, Guangdong, China TEL: 86-755-26954280 FAX: 86-755-26954282 SHENZHEN EMTEK CO., LTD. REPORT NO: ES101009016F FCC ID: XDP-GT09010 DATE: 2/11/2011 Page 2 of 36 VERIFICATION OF COMPLIANCE Applicant: GLOBAL TECH CHINA LTD. Room 12, 14th Floor, Tower 2, Evergain Plaza, 88 Container Port Road, Kwai Chung, HongKong Manufacturer: GLOBAL TECH CHINA LTD. Room 12, 14th Floor, Tower 2, Evergain Plaza, 88 Container Port Road, Kwai Chung, HongKong Product Description: L Digital / 2.4G RF Door Entry Camera (Transmitter) Brand Name: N/A Model Number: GT09010 Serial Number: N/A File Number: ES101009016F Date of Test: January 28, 2011 to January 31, 2011 We hereby certify that: The above equipment was tested by SHENZHEN EMTEK CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2009) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247. The test results of this report relate only to the tested sample identified in this report. Approved By David Lee / Q.A. Manager SHENZHEN EMTEK CO., LTD. SHENZHEN EMTEK CO., LTD. REPORT NO: ES101009016F FCC ID: XDP-GT09010 DATE: 2/11/2011 Page 3 of 36 Table of Contents 1. GENERAL INFORMATION ................................................................................................. 5 1.1 P RODUCT DESCRIPTION.............................................................................................................. 5 2.1 EUT CONFIGURATION................................................................................................................ 6 2.2 EUT EXERCISE........................................................................................................................... 6 2.3 T EST PROCEDURE....................................................................................................................... 6 2.4 LIMITATION................................................................................................................................6 2.4 C ONFIGURATION OF TESTED SYSTEM....................................................................................... 10 3. DESCRIPTION OF TEST MODES .................................................................................... 11 4. RADIATED EMISSION TEST ............................................................................................ 12 4.1 M EASUREMENT PROCEDURE..................................................................................................... 12 4.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)............................................................ 12 4.3 MEASUREMENT EQUIPMENT USED: .......................................................................................... 13 4.4 RADIATED EMISSION LIMIT......................................................................................................... 13 4.5 MEASUREMENT RESULT................................................................................................................ 14 4.6 RADIATED MEASUREMENT PHOTOS: .......................................................................................... 20 5. CHANNEL SEPARATION TEST ....................................................................................... 21 5.1 MEASUREMENT PROCEDURE..................................................................................................... 21 5.2 T EST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)............................................................ 21 5.3 MEASUREMENT EQUIPMENT USED: .......................................................................................... 21 5.4 MEASUREMENT RESULTS:......................................................................................................... 21 6. 20DB BANDWIDTH TEST .................................................................................................. 24 6.1 M EASUREMENT PROCEDURE..................................................................................................... 24 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)............................................................ 24 6.3 MEASUREMENT EQUIPMENT USED: .......................................................................................... 24 6.4 M EASUREMENT RESULTS:......................................................................................................... 24 7. QUANTITY OF HOPPING CHANNEL TEST.................................................................. 27 7.1 M EASUREMENT PROCEDURE..................................................................................................... 27 7.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)............................................................ 27 7.3 M EASUREMENT EQUIPMENT USED: .......................................................................................... 27 7.4 M EASUREMENT RESULTS:......................................................................................................... 27 8. TIME OF OCCUPANCY (DWELL TIME) TEST ............................................................ 29 8.1 MEASUREMENT PROCEDURE..................................................................................................... 29 8.2 T EST SET-UP (BLOCK DIAGRAM OF…

Text truncated - open the document above for the full version.

RADIATED EMISSION TEST