XHT-1014148-1Toy RC Orbit Tumbler Glow in the Dark

The artwork and design of this manual are protected by US copyright law and may not be reproduced, distributed, displaced, published or used for any purpose without prior written permission. Altering, removing or reproducing any of the trademark or copyright notices on this package is not permitted. Sharper Image® name and logo are registered trademarks. Distributed by and © 2020 MerchSource, LLC. Irvine, CA 92618. All rights reserved OPERATING INSTRUCTIONS The car requires 6 AA (1.5V) alkaline batteries (not included). The battery compartment is on the underside of the vehicle. Loosen the screw using a phillips or cross screwdriver to remove the battery cover. Insert the AA batteries according to the diagram inside the battery tray. Replace battery cover and tighten screws. iiiiiiiiiiii Carefully remove items from package. BATTERY WARNING: • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries. • Alkaline batteries are recommended. Use only the specified voltage. • Insert batteries using the correct polarity. Always use, replace, and recharge (if applicable) batteries under adult supervision. • Do not charge with non-rechargeable batteries. • Do not short-circuit the battery supply terminals. • Do not dispose of batteries in a fire, batteries may explode or leak. • Remove batteries before storing. • Recycle or dispose of batteries according to federal, state, and local laws. • Keep these instructions for future reference. • Avoid water when operating. • Do not submerge car or controller in water. • Do not use people or animals as obstacles. • Do not run car into furniture objects or hard surfaces as this will cause damage to both the objects and car. • Keep fingers, hair and loose clothing away from the tires, gears and motor while car is switched to “ON”. • Do not leave car or remote control near sources of heat or under direct sunlight for long periods of time. • Remove all batteries when not in use to avoid accidental operation. • Adult supervision is recommended when operating car. • Thoroughly inspect products before every use. If the product appears worn, frayed/splintered, cracked, or broken in any manner, discontinue use and discard immediately. Forward Spinning Action Tumbling This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT INFORMATION FOR FUTURE REFERENCE. Due to continuous product improvements, the pictures on this manual may dier slightly from the actual product. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. SAFETY PRECAUTIONS 1-800-374-2744 6+ * Press and Hold Reverse * Press and Hold Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Printed in ChinaModel Number: 1014148 * Press and Hold Note: for best operation, use vehicle on hard rough surface. When the vehicle is moving forward or backward and push the stunt button, it will cause it to flip over. GLOW IN THE DARK ORBIT TUMBLER The remote control requires 4 AA (1.5V) alkaline batteries (not included). Loosen the screw at the bottom of the remote using a phillips or cross screwdriver to remove the battery cover. Insert the batteries according to the diagram inside the battery tray. Replace battery cover and tighten screw. Battery Compartment Screw Power Switch Pairing: The Orbit Tumbler and Remote must be paired before driving. 1. Rotate the remote power knob clockwise to turn on the remote. The status light on the antenna cover will pulse. 2. Turn on Orbit Tumbler – its lights will flash rapidly. 3. The lights on the Orbit Tumbler and Remote will stop flashing when they are paired. If you have more than one vehicle and remote, you must pair one first, and then you may pair others. Charging the Glow In The Dark Cage: Place the Orbit Tumbler in direct sunlight for approximately 60 minutes. The cage will now glow in the dark for up to 20 minutes. Power Knob Left Wheels Right Wheels Stunt Button Status Light L’illustration et la conception de ce manuel sont protégées par la Loi sur le droit d’auteur des États-Unis, et ne peuvent être reproduites, distribuées, achées, publiées ou utilisées pour tout usage sans une autorisation écrite préalable. Il est interdit de modifier, de retirer ou de reproduire toute marque de commerce…

Text truncated - open the document above for the full version.

APPENDIXB GuangdongYinrunIndustryCo.,Ltd. 2021-6-3 FederalCommunicationsCommission 44512 th StreetSW Washington,DC20554 Subject:LimitedAgencyAgreement GuangdongYinrunIndustryCo.,Ltd. FCCID:XHT-1014148-1 ToWhomItMayConcern: We,GuangdongYinrunIndustryCo.,Ltd.,herebyauthorizedIntertekTestingServicestoactas ourAgentforthepurposeofpreparingapplicationforFCCIDnumberXHT-1014148-1underall applicablepartsoftheFCCrulesandregulations. Theeffectivedateofthislimitedagencyagreementis2021-3-15.TheLimitedAgency Agreementexpireson2022-3-15,unlesssoonerterminatedorextendedbywrittennoticeto IntertekTestingServicesandtheFederalCommunicationsCommission. ThisistoadvisethatweareinfullcompliancewiththeAnti-DrugAbuseAct.Theapplicantis notsubjecttoadenialoffederalbenefitspursuanttoSection5301oftheAnti-DrugActof1988, 21U.S.C.862,andnopartytotheapplicationissubjecttoadenialoffederalbenefitspursuantto thatsection. Ifyouhaveanyquestionsorcomments,pleasedonothesitatetocontactme. Sincerely, [Signature] CYRUSYANG GENERALMANAGER

APPENDIXE（Option1） GuangdongYinrunIndustryCo.,Ltd. Attention:Certificationreviewer RE:RequestforConfidentiality FCCID:XHT-1014148-1 ToWhomItMayConcern: PermanentConfidentiality[Completethissectionifpermanentconfidentialityisrequested] Requesttowithholdpermanentlyfrompublicreviewcertainportionsoftheapplicationforequipment certificationforthereferencedFCCidentifiers.Thisrequestforconfidentialityismadepursuantto47 CFR0.457(d)and0.459oftheFCCRules.Inparticular,thefollowingsectionsoftheapplicationaretobe keptpermanentlyconfidential: [Selectoneormoreofitemsbelow,asappropriate,anddeleteunselectedparts] Schematics BlockDiagrams OperationalDescription InternalPhotos(seenote) UsersManual(seenote) Note1:InternalPhotosmaybeheldconfidential1)ifthecircuitboardorinternalcomponentsarenotaccessible tousers.Forexample,itisacceptableifthecircuitboardisenclosedinepoxy.2)Also,itisacceptableif thedeviceisnotaccessibletothepublic,forexample,adevicemountedonthetopofalargetower(or inafencedenclosure)suchthatitisonlyserviceablebyprofessionaldesignatedtechniciansundera Non-DisclosureAgreement(NDA).AllsalesforthesedevicesmustbeunderaNDArestrictingthe disclosureoftheproprietyinformation,includinginternalphotos. UsersManualmaybeheldconfidentialonlywhenthemanualcontainsproprietarytechnicalinformation intendedforprofessionaltechniciansobligatedunderaNDA.Allsalesanddistributionoftheuser’s manualmustbeunderaNDAthatrestrictsthedisclosureoftheinformation. Intheapplicationcoverletterrequestingpermanentconfidentialitythefollowingadditionaldescription andtheNDAexhibitisrequired: 1.Describeindetailhowinternalphotosand/orusersmanualinformationarecontrolledtopreventthem frombecomingpublicordisclosedtounauthorizedpersons. 2.Describehowpublicaccessisrestrictedforproductsserviceablebyprofessionaldesignated technicians. 3.Astatementthatallsalesofthenon-consumerdevicewillbeunderaNDAtoincludethirdpartysales andthatthefinaluserofthedeviceissubjecttotheNDA. 4.ProvideanexampleoftheNDAbetweenthegranteeandapurchaser.Therequestforconfidentiality must Note2:Forscanningreceiver,theschematics,blockdiagrams,operationaldescription,tune-upprocedure,partslistand internalphotosarealways heldpermanentlyconfidential. Rationaleforrequestforconfidentiality: Wehaveinvestedconsiderabletimeandmaterialsinresearchanddevelopmenttoproducethereferenced product. Permanentconfidentiality:Disclosureofthepermanentlyconfidentialportionsofthisapplicationto competitorswouldnotonlygivethemsignificantcompetitiveadvantagesindevelopingsimilarproducts, butwouldalsodisclosesuccessfulimplementationofunpublished,leadingedgetechnologydevelopedby us. Ifyouhavequestionsorneedfurtherinformation,pleasecontacttheundersigned. Sincerely, _________________ CYRUSYANG GENERALMANAGER 2021-6-3

Page 1 of 2 EXTERNAL PHOTOS Page 2 of 2

1014148 20 MechSouce LL Irv, CA. Made in a M F ID: ORBIT GLOW TUMBLER

Page 1 of 2 INTERNAL PHOTOS Page 2 of 2

1 INTERTEK TESTING SERVICES RF Exposure The equipment under test (EUT) is an Toy RC Orbit Tumbler Glow in the Dark operating at 2.4G Band. The EUT can be powered by DC 6.0V (4 x 1.5V AA batteries). For more detail information pls. refer to the user manual. Antenna Type: Integral antenna. Antenna Gain: 0dBi. The normal radiated output power (e.i.r.p) is: -20.0dBm (tolerance: +/- 3dB). The normal conducted output power is -20.0dBm (tolerance: +/- 3dB). Modulation Type: GFSK According to the KDB 447498: The Maximum peak radiated emission for the EUT is 75.8 dBμV/m at 3m in the frequency 2475MHz The EIRP = [(FS*D) ^2 / 30] mW = -19.43dBm which is within the production variation. The Minimum peak radiated emission for the EUT is 73.4 dBμV/m at 3m in the frequency 2405MHz The EIRP = [(FS*D) ^2 / 30] mW = -21.83dBm which is within the production variation. The maximum conducted output power specified is -17.0dBm= 0.020mW The source- based time-averaging conducted output power =0.020* Duty cycle mW <0.020 mW(Duty cycle <100%) The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.475) mW = 9.53 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. The duty cycle is simply the on-time divided by the period: The duration of one cycle = 18.2609ms Effective period of the cycle = = 797.1μs x1 = 0.7971ms DC =0.7971ms / 18.2609ms =0.0437 or 4.37% FCC ID: XHT-1014148-1

Guangdong Yinrun Industry Co., LTD. TEST REPORT SCOPE OF WORK FCC TESTING– MODEL: 1014148 REPORT NUMBER GZHH00410731-001 ISSUE DATE Jun 26, 2021 PAGES 24 DOCUMENT CONTROL NUMBER FCC ID 249_C © 2017 INTERTEK Intertek Report No.: GZHH00410731-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Service Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community GuanHu Subdistrict, LongHua District, Shenzhen, People’s Republic of China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page: 1 of 24 FCC ID 249_C Test Report Guangdong Yinrun Industry Co., LTD. Application for Certification FCC ID: XHT-1014148-1 Toy RC Orbit Tumbler Glow in the Dark Model: 1014148 2.4GHz Transceiver Report No.: GZHH00410731-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-19] Prepared and Checked by: Approved by: Sign on file Maura Wang Engineer Peter Kang Technical Supervisor Date: Jun 26, 2021 Intertek Report No.: GZHH00410731-001 Version: 01-November-2017 Page: 2 of 24 FCC ID 249_C Test Report MEASUREMENT/TECHNICAL REPORT This report concerns (check one:) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-19 Edition] provision. Report prepared by: Maura Wang Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community GuanHu Subdistrict, LongHua District, Shenzhen, People’s Republic of China Tel / Fax: 86-755-8601 6288/86-755-8601 6751 Intertek Report No.: GZHH00410731-001 Version: 01-November-2017 Page: 3 of 24 FCC ID 249_C Test Report Table of Contents 1.0 Summary of Test Result .......................................................................................... 4 2.0 General Description ................................................................................................. 5 2.1 Product Description ................................................................................................. 5 2.2 Related Submittal(s) Grants .................................................................................... 5 2.3 Test Methodology .................................................................................................... 5 2.4 Test Facility ............................................................................................................ 5 3.0 System Test Configuration ...................................................................................... 6 3.1 Justification ............................................................................................................. 6 3.2 EUT Exercising Software ......................................................................................... 6 3.3 Special Accessories ................................................................................................ 6 3.4 Equipment Modification ........................................................................................... 6 3.5 Measurement Uncertainty ....................................................................................... 6 3.6 Support Equipment List and Description .................................................................. 6 4.0 Emission Results ..................................................................................................... 7 4.1 Radiated Test Results ............................................................................................. 7 4.1.1 Field Strength Calculation ..................................................................................... 7 4.1.2 Radiated Emission Configuration Photograph ....................................................... 8 4.1.3 Radiated Emissions .............................................................................................. 8 4.1.4 Transmitter Spurious Emissions ......................................................................... 11 5.0 Equipment Photographs ........................................................................................ 15 6.0 Product Labelling ................................................................................................... 15 7.0 Technical Specifications ........................................................................................ 15 8.0 Instruction Manual ................................................................................................. 15 9.0 Miscellaneous Information .................................................................................... 16 9.1 Bandedge Plot .............................................................................…

Text truncated - open the document above for the full version.

Page 1 of 2 RADIATED PHOTOS Up to 1GHz (EUT was placed in the centre of the turntable) Page 2 of 2 Above 1GHz (EUT was placed in the centre of the turntable)