XIA-CFW32125G Sub6 Self Install Outdoor CPE

User Guide (Carrier) AurusLink+ Outdoor CPE Release 16 Self Install Model CFW-3211/3212 Doc No. UG01437 2 of 81 CFW-3211/3212 – User Guide (Carrier) UG01437 v1.00 23 December, 2022 Important notice This device, like any wireless device, operates using radio signals which cannot guarantee the transmission and reception of data in all conditions. While the delay or loss of signal is rare, you should not rely solely on any wireless device for emergency communications or otherwise use the device in situations where the interruption of data connectivity could lead to death, personal injury, property damage, data loss, or other loss. Casa Systems accepts no responsibility for any loss or damage resulting from errors or delays in transmission or reception, or the failure of the Casa Systems AurusLINK+ 5G Outdoor CPE to transmit or receive such data. Safety and hazards W Warning – Do not connect or disconnect cables or devices to or from the USB port, SIM card tray, or Ethernet port in hazardous locations such as those in which flammable gases or vapours may be present, but normally are confined within closed systems; are prevented from accumulating by adequate ventilation; or the location is adjacent to a location from which ignitable concentrations might occasionally be communicated. Copyright Copyright© 2022 Casa Systems. All rights reserved. The information contained herein is proprietary to Casa Systems. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of Casa Systems. Trademarks and registered trademarks are the property of Casa Systems or their respective owners. Specifications are subject to change without notice. Images shown may vary slightly from the actual product. N Note – This document is subject to change without notice. Document history This document applies to the following CPE model: AurusLink+ Outdoor CPE – CFW-3211/3212 Ver. Document description Date v1.00 Initial document release 23 December, 2022 TTable i. – Document revision history 3 of 81 CFW-3211/3212 – User Guide (Carrier) UG01437 v1.00 23 December, 2022 Contents 11 Document overview ...................................................................................................................................................................... 6 1.1 Introduction .................................................................................................................................................................................................................. 6 1.1.1 Organisation of this Document ......................................................................................................................................................................... 6 Section 1 – Device description and general overview of end-user installation ..............................................................................................................................6 Section 2 – Device configuration details ..................................................................................................................................................................................................6 1.2 Target audience ........................................................................................................................................................................................................... 6 1.2.1Notation..................................................................................................................................................................................................................7 2 Product introduction ..................................................................................................................................................................... 8 2.1 Product overview ......................................................................................................................................................................................................... 8 2.2 Package contents ......................................................................................................................................................................................................... 8 2.2.1 Other tools required............................................................................................................................................................................................ 8 3Physicaldimensionsandinterfaces............................................................................................................................................9 3.1 Physical dimensions .................................................................................................................................................................................................... 9 3.1.1 CFW-3211/3212 .................................................................................................................................................................................................... 9 3.2 Interface ...................................................................................................................................................................................................................... 10 3.2.1 CFW-3211/3212 ................................................................................................................................................................................................. 10 3.2.2 PoE injector ......................................................................................................................................................................................................... 12 3.3 LED indicator lights ................................................................................................................................................................…

Text truncated - open the document above for the full version.

NetComm Wireless Pty Ltd Level 5, 18-20 Orion Road, Lane Cove,NSW, 2066, Australia 18-20 Orion Roa d Lane Cove, NSW 2066, A ustra lia + 61 2 9424 2000 N e t C o m m W i r e l e s s P t y L t d A C N 0 0 2 49 0 48 6, a c q u i r e d b y C a s a S y s t e m s In c . CFR 47 §2.911(d)(5)(i)(ii) Attestation Letter Attestation Letter Date: 2023-04-21 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii) Filing FCC ID: XIA-CFW3212 NetComm Wireless Pty Ltd certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. NetComm Wireless Pty Ltd certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature Printed Name: Pat Sinni Title: Certification and Compliance Team Leader

NetComm Wireless Pty Ltd Level 5, 18-20 Orion Road, Lane Cove,NSW, 2066, Australia 18-20 Orion Roa dLane Cove, NSW 2066, A ustra lia + 61 2 9424 2000 N e t C o m m W i r e l e s s P t y L t d A C N 0 0 2 49 0 48 6, a c q u i r e d b y C a s a S y s t e m s In c . Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 30, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing NetComm Wireless Pty Ltd certifies that, as of the date of the filing of the application, Americas Compliance Consulting LLc dba iCertifi. is our designated U.S. agent for service of process. NetComm Wireless Pty Ltd accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Americas Compliance Consulting LLc dba iCertifi. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process. Sincerely, Designated U.S. Agent Information: FRN: 0033399411 Name: Americas Compliance Consulting LLc dba iCertifi Contact Person: Mr Paul A Preston Address: 1001 SW Disk Drive, ste 250 Office 3 Bend, OR 97702 United States Tel.: (866) 885-4575 Email: [email protected] U.S. Agent Signature: Applicant: Company Name: NetComm Wireless Pty Ltd Grantee Code: XIA Contact Person: Pat Sinni Address: Level 5, 18-20 Orion Road, Lane Cove NSW 2066, Australia Tel.: +61 2 9424 2000 Email: [email protected] Applicant Signature: U.S. AGENT LETTER OF ATTESTATION

NetComm Wireless Pty Ltd Level 5, 18-20 Orion Road, Lane Cove,NSW, 2066, Australia 18-20 Orion Roa d Lane Cove, NSW 2066, A ustra lia + 61 2 9424 2000 N e t C o m m W i r e l e s s P t y L t d A C N 0 0 2 49 0 48 6, a c q u i r e d b y C a s a S y s t e m s In c . Date: 2023-08-05 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir/Madam, We, NetComm Wireless Pty Ltd, hereby authorize China Certification ICT Co., Ltd (Dongguan) to act as a laboratory for testing and test report generation for the following project(s): (Product description: 5G Sub6 Self Install Outdoor CPE, model name: CFW-3212 FCC ID: XIA-CFW3212) The device supports 2.4G WiFi,Bluetooth BDR(GFSK), EDR(π/4-DQPSK, 8DPSK)! and BLE Mode, but for this device, only BLE was active, the others were disabled by software. Sincerely Yours, Client’s signature Printed Name: Pat Sinni Title: Certification and Compliance Team Leader Attestation Letter

NetComm Wireless Pty Ltd Level 5, 18-20 Orion Road, Lane Cove,NSW, 2066, Australia 18-20 Orion Roa d Lane Cove, NSW 2066, A ustra lia + 61 2 9424 2000 N e t C o m m W i r e l e s s P t y L t d A C N 0 0 2 49 0 48 6, a c q u i r e d b y C a s a S y s t e m s In c . FCC Authorization Date: 2023-04-21 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , NetComm Wireless Pty Ltd, Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Pat Sinni Title: Certification and Compliance Team Leader QA-FR-170-B

NetComm Wireless Pty Ltd Level 5, 18-20 Orion Road, Lane Cove,NSW, 2066, Australia 18-20 Orion Roa d Lane Cove, NSW 2066, A ustra lia + 61 2 9424 2000 N e t C o m m W i r e l e s s P t y L t d A C N 0 0 2 49 0 48 6, a c q u i r e d b y C a s a S y s t e m s In c . FCC Confidential Authorization Date: 2023-04-21 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: XIA-CFW3212 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, (NetComm Wireless Pty Ltd) hereby requests long-term confidential treatment of information accompanying this application as outlined below: • Block Diagram • Schematics • Operation Description As well as short-term (secrecy cycle: 180 days) confidential treatment of information accompanying this application as outlined below: • Internal Photos • User’s Manual • External Photos • Test Set-up Photos The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed Name: Pat Sinni Title: Certification and Compliance Team Leader

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Adapter port port

Device Label 5G Sub6 Self Install Outdoor CPE Model: CFW-3212 Part Code: CFW-3212-01 Manufactured: DD/MM/YYYY Power Input: 24V PoE, 24W IP65 S/N: 216646YYWWNNNNN IMEI: TTTTTTTTNNNNNNC Designed in Australia. Assembled in China. Revision: 0.01 FCC ID:XIA-CFW3212 Contain FCC ID:XIA2023RG520NNA

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS uncover WWAN Module Antenna A WWAN Module Antenna B WWAN Module Antenna C WWAN Module Antenna D BLE Antenna WAAN Module FCC ID: XIA2023RG520NNA

China Certification ICT Co., Ltd (Dongguan) Report No.: CR221264490-00BM2 Page 46 of 49 5. RF EXPOSURE EVALUATION 5.1 Applicable Standard According to subpart 15.247(i)and subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According to §1.1310 and §2.1091 RF exposure is calculated. Calculation formula: Prediction of power density at the distance of the applicable MPE limit S = PG/4R² = power density (in appropriate units, e.g. mW/cm 2 ); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); For simultaneously transmit system, the calculated power density should comply with: China Certification ICT Co., Ltd (Dongguan) Report No.: CR221264490-00BM2 Page 47 of 49 5.2 EUT WWAN Information▲: Operation Modes Operation Frequency (MHz) Maximum Conducted Power including Tune-up Tolerance (dBm) Antenna Gain (dBi) ERP or EIRP (dBm) ERP or EIRP Limit (dBm) Conducted Power Limit (dBm) LTE/NR B2 1850-1910 252.23 27.2333 / LTE B4 1710-1755 253.27 28.2730 / LTE/NR B5 824-849 25-0.24 22.6138.45 / LTE/NR B7 2500-2570 254.02 // 33 LTE/NR B12 699-716 25-0.55 22.344.77 / LTE/NR B13 777-787 250.64 23.4944.77 / LTE/NR B14 788-798 250.54 23.3944.77 / LTE B17 704-716 25-0.55 22.344.77 / LTE/NR B25 1850-1915 252.23 27.2333 / LTE/NR B26 814-849 25-0.11 24.8938.45 / LTE/NR B30 2305-2315 252.68 27.6833 / LTE/NR B38 2570-2620 283.15 31.1533 / LTE B41 2496-2690 284.02 // 33 NR B41 2496-2690 314.02 // 33 LTE/NR B48 3550-3700 202.48 22.4823 / LTE/NR B66 1710-1780 253.27 28.2730 / LTE/NR B71 663-698 25-0.81 22.0444.77 / NR B77 3450-3550 3700-3980 31 4.43 35.43 62.15 / NR B78 3300-3800 312.95 33.9562.15 / Note: The devices contain certified WWAN Module, FCC ID: XIA2023RG520NNA. The device was used for fixed application. China Certification ICT Co., Ltd (Dongguan) Report No.: CR221264490-00BM2 Page 48 of 49 5.3 Measurement Result Operation Modes Frequency (MHz) Antenna Gain Conducted output power including Tune-up Tolerance Evaluation Distance Power Density MPE Limit (dBi) (numeric)(dBm) (mW) (cm) (mW/cm 2 ) (mW/cm 2 ) BLE 2402-2480 2.66 1.85 3 2.00 20 0.0007 1 LTE/NR B2 1850-1910 2.23 1.67 25 316.23 20 0.1051 1 LTE B4 1710-1755 3.27 2.12 25 316.23 20 0.1334 1 LTE/NR B5 824-849 -0.24 0.95 25 316.23 20 0.0598 0.549 LTE/NR B7 2500-2570 4.02 2.52 25 316.23 20 0.1585 1 LTE/NR B12 699-716 -0.55 0.88 25 316.23 20 0.0554 0.466 LTE/NR B13 777-787 0.64 1.16 25 316.23 20 0.0730 0.518 LTE/NR B14 788-798 0.54 1.13 25 316.23 20 0.0711 0.525 LTE B17 704-716 -0.55 0.88 25 316.23 20 0.0554 0.469 LTE/NR B25 1850-1915 2.23 1.67 25 316.23 20 0.1051 1 LTE/NR B26 814-849 -0.11 0.97 25 316.23 20 0.0610 0.543 LTE/NR B30 2305-2315 2.68 1.85 25 316.23 20 0.1164 1 LTE/NR B38 2570-2620 3.15 2.07 28 630.96 20 0.2598 1 LTE B41 2496-2690 4.02 2.52 28 630.96 20 0.3163 1 NR B41 2496-2690 4.02 2.52 31 1258.93 20 0.6311 1 LTE/NR B48 3550-3700 2.48 1.77 20 100.00 20 0.0352 1 LTE/NR B66 1710-1780 3.27 2.12 25 316.23 20 0.1334 1 LTE/NR B71 663-698 -0.81 0.83 25 316.23 20 0.0522 0.442 NR B77 3450-3550 3700-3980 4.43 2.77 31 1258.93 20 0.6938 1 NR B78 3300-3800 2.95 1.97 31 1258.93 20 0.4934 1 China Certification ICT Co., Ltd (Dongguan) Report No.: CR221264490-00BM2 Page 49 of 49 The WWAN and BlE can transmit simultaneously, the worst case as below:: =S WWAN /S limit- WAAN + S BLW /S limit- BLE =0.6938/1+0.0007/1 =0.69 < 1.0 Result: The device compliant the Exemption at 20cm distances. ===== END OF REPORT ====

Approval sheet Page 1 of 9 ASC_RFANT5220110A0T_V12 Apr. 2010 MULTILAYER CERAMIC ANTENNA RFANT Pb free Series – RoHS Compliance 2.4 GHz ISM Band Working Frequency P/N: RFANT5220110A0T *Contents in this sheet are subject to change without prior notice. Approval sheet Page 2 of 9 ASC_RFANT5220110A0T_V12 Apr. 2010 FEATURES
Surface Mounted Devices with a small dimension of 5.2 x 2.0 x 1.1 mm 3 meet future miniaturization trend.
Embedded and LTCC (Low Temperature Co-fired Ceramic) technology is able to future integrate with system design as well as beautifying the housing of final product.
High Stability in Temperature / Humidity Change APPLICATIONS
Bluetooth
Wireless LAN
HormRF
ISM band 2.4GHz wireless applications DESCRIPTION Walsin Technology Corporation develops a new ceramic embedded antenna specified for 2.4 GHz ISM Band application, as shown in below “CONSTRUCTION”. Both of Wireless LAN IEEE 802.11b and Bluetooth TM typically located on this unlicensed frequency band which range covers from 2.4GHz to 2.4835GHz. To fulfil the friendly usage for antenna, this antenna has been designed to a typical 150MHz bandwidth through Walsin’s advanced LTCC (Low Temperature Co-fired Ceramic) technology and superior product design via 3D EM Simulation Skill. This antenna has a rectangular ceramic body with a tiny dimension of 5.2x 2.0 x 1.1 mm 3 meet the future SMT automation and miniaturization requirements on modern portable devices. CONSTRUCTION Fig 1. Outline of 2.4GHz Antenna – RFANT5220110A0T Fig 2. Dimension L= 2.0 ±0.2 mm T= 1.15 ±0.10 mm W = 5.2 ± 0.2 mm A = 0.40 ± 0.25 mm A = 0.40 ± 0.25 mm WTC L= 2.0 ±0.2 mm T= 1.15 ±0.10 mm W = 5.2 ± 0.2 mm A = 0.40 ± 0.25 mm A = 0.40 ± 0.25 mm WTC L= 2.0 ±0.2 mm T= 1.15 ±0.10 mm W = 5.2 ± 0.2 mm A = 0.40 ± 0.25 mm A = 0.40 ± 0.25 mm WTC Identification mark Soldering terminal W T C W T C Feeding Identification mark Soldering terminal W T C W T C Feeding Approval sheet Page 3 of 9 ASC_RFANT5220110A0T_V12 Apr. 2010 SOLDER LAND PATTERN DESIGN Figure ELECTRICAL CHARACTERISTICS RFANT5220110A0T Specification Working Frequency Range 2.4 GHz ～ 2.5GHz Gain 2.66 dBi VSWR 2 max. Polarization Linear Azimuth Bandwidth Omni-directional Impedance 50Ω Rated Power (max.) 3 Watts Maximum Input Power 5 Watts for 5 minutes Operation Temperature -40 ̊C ~ +85 ̊C Remark: The specification is defined based on the test board dimension as in below Approval sheet Page 4 of 9 ASC_RFANT5220110A0T_V12 Apr. 2010 Antenna on Test Board ( FR4 Thickness 0.8mm) Antenna S11 on Test Board Bandwidth >150MHzBandwidth >150MHz Empty Area Empty Area 18x9 mm 50Ω ΩΩ ΩFeed line GROUND 30x18 mm 1mm 3.3mm 1.5mm WTC 2.5mm 18mm Empty Area Empty Area 18x9 mm 50Ω ΩΩ ΩFeed line GROUND 30x18 mm 1mm 3.3mm 1.5mm WTC 2.5mm 18mm Approval sheet Page 5 of 9 ASC_RFANT5220110A0T_V12 Apr. 2010 RADIATION PATTERN Radiation Pattern and Gain were dependent on measurement board design. The specification of RFANT5220110A0T antenna was measured based on the PCB size and installation position as shown in the below figure Test Board Vertical Horizontal Y - Z Plane Average Gai n= -0.82 dBi Peak Gain = 1.69 dBi Average Gain =-3.22 dBi Peak Gain= -5.42 dBi Average Gain=-8.98 dBi X - Z Plane Average Gain=-0.91 dBi Peak Gain= -5.97 dBi Average Gain=-3.24dBi Peak Gain= 2.66 dBi Average Gain= -8.61 dBi X - Y Plane Average G ain= -0.68 dBi Peak Gain= -5.97 dBi Average Gain=-3.12 dBi Peak Gain= 2.59 dBi Average Gain= -9.24 dBi Y Z WTC X Y Z WTC X Y Z WTC X Y Z WTC X Y Z WTC X Y Z WTC X z Y z Y z X z X X Y X Y Empty Area GROUND 30x18 mm WTC X Y Z Empty Area GROUND 30x18 mm WTC X Y Z X Y Z Approval sheet Page 6 of 9 ASC_RFANT5220110A0T_V12 Apr. 2010 RELIABILITY TEST Test item Test condition / Test method Specification Solderability JIS C 0050-4.6 JESD22-B102D *Solder bath temperature：235 ± 5°C *Immersion time：2 ± 0.5 sec *Solder：Sn3Ag0.5Cu for lead-free At least 95% of a surface of each terminal electrode must be covered by fresh solder. Leaching (Resistance to dissolution of metallization) IEC 60068-2-58 *Solder bath temperature ：260 ± 5°C *Leaching immersion time：30 ± 0.5 sec *Solder : SN63A Loss of metallization on the edges of each electrode shall not exceed 25%. Resistance to soldering heat JIS C 0050-5.4 *Preheating temperature ：120~150°C, 1 minute. *Solder temperature：270±5°C *Immersion time：10±1 sec *Solder：Sn3Ag0.5Cu for lead-free Measurement to be made after keeping at room temperature for 24±2 hrs No mechanical damage. Samples shall satisfy electrical specification after test. Loss of metallization on the edges of each electrode shall not exceed 25%. Drop Test JIS C 0044 *Height ：75 cm *Test Surface ：Rigid surface of concrete or steel. *Times：6 surfaces for each units；2 times for each side. No mechanical damage. Samples shall satisfy electrical specification after test. Adhesive Strength of Termination JIS C 0051- 7.4.3 *Pressurizing force： 5N(≦0603)；10N(>0603) *Test time：10±1 sec No remarkable damage or removal of the termination. Bending test JIS C 0051- 7.4.1 The middle part of substrate shall be pressurized by means of the pressurizing rod at a rate of about 1 mm/s per second until the deflection becomes 1mm/s and then pressure shall be maintained for 5 ±1 sec. Measurement to be made after keeping at room temperature for 24 ±2 hours No mechanical damage. Samples shall satisfy electrical specification after test. Approval sheet Page 7 of 9 ASC_RFANT5220110A0T_V12 Apr. 2010 Temperature cycle JIS C 0025 1. 30 ±3 minutes at -40°C±3°C, 2. 10~15 minutes at room temperature, 3. 30±3 minutes at +85°C±3°C, 4. 10~15 minutes at room temperature, Total 100 continuous cycles Measurement to be made after keeping at room temperature for 24 ±2 hrs No mechanical damage. Samples shall satisfy electrical specification after test. Vibration JIS C 0040 *Frequency：10Hz~55Hz~10Hz(1min) *Total amplitude：1.5mm *Test times：6hrs.(Two hrs each in three mutually perpendicular directions) No mechanical damage. Samples shall satisfy electri…

Text truncated - open the document above for the full version.

TEST REPORT Applicant: NetComm Wireless Pty Ltd Address: Level 5, 18-20 Orion Road,Lane Cove NSW 2066,Australia FCC ID: XIA-CFW3212 Product Name: 5G Sub6 Self Install Outdoor CPE Standard(s): 47 CFR Part 15, Subpart C(15.247) ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR221264490-00BM2 Date Of Issue: 2023/8/5 Reviewed By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR221264490-00BM2 Page 2 of 49 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR221264490-00BM2 Page 3 of 49 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 DOCUMENT REVISION HISTORY .......................................................................................... 5 1. GENERAL INFORMATION .................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 6 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 7 1.2.2 Support Equipment List and Details .............................................................................................................. 7 1.2.3 Support Cable List and Details ...................................................................................................................... 7 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 8 1.3 MEASUREMENT UNCERTAINTY .......................................................................................................... 9 2. SUMMARY OF TEST RESULTS .......................................................................................... 10 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 11 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 11 3.1.1 Applicable Standard ..................................................................................................................................... 11 3.1.2 EUT Setup.................................................................................................................................................... 12 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 12 3.1.4 Test Procedure ............................................................................................................................................. 13 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 13 3.2 RADIATION SPURIOUS EMISSIONS .................................................................................................... 14 3.2.1 Applicable Standard ..................................................................................................................................... 14 3.2.2 EUT Setup.................................................................................................................................................... 14 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 15 3.2.4 Test Procedure ............................................................................................................................................. 15 3.2.5 Corrected Amplitude & Margin Calculation ................................................................................................ 15 3.3 6 DB EMISSION BANDWIDTH: ............................................................................................................ 16 3.3.1 Applicable Standard ..................................................................................................................................... 16 3.3.2 EUT …

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View Radiated Emission Below 1GHz View Radiated Emission Above 1GHz View