XMR202303AF51YWi-Fi & Bluetooth Module

AF51Y Hardware Design Wi-Fi&Bluetooth Module Series Version: 1.0.1 Date: 2021-07-19 Status: Preliminary Wi-Fi&Bluetooth Module Series AF51Y_Hardware_Design 1 / 47 Our aim is to provide customers with timely and comprehensive service. For any assistance, please contact our company headquarters: Quectel Wireless Solutions Co., Ltd. Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai 200233, China Tel: +86 21 5108 6236 Email: [email protected] Or our local office. For more information, please visit: http://www.quectel.com/support/sales.htm. For technical support, or to report documentation errors, please visit: http://www.quectel.com/support/technical.htm Or email to [email protected]. General Notes Quectel offers the information as a service to its customers. The information provided is based upon customers’ requirements. Quectel makes every effort to ensure the quality of the information it makes available. Quectel does not make any warranty as to the information contained herein, and does not accept any liability for any injury, loss or damage of any kind incurred by use of or reliance upon the information. All information supplied herein is subject to change without prior notice. Disclaimer While Quectel has made efforts to ensure that the functions and features under development are free from errors, it is possible that these functions and features could contain errors, inaccuracies and omissions. Unless otherwise provided by valid agreement, Quectel makes no warranties of any kind, implied or express, with respect to the use of features and functions under development. To the maximum extent permitted by law, Quectel excludes all liability for any loss or damage suffered in connection with the use of the functions and features under development, regardless of whether such loss or damage may have been foreseeable. Duty of Confidentiality The Receiving Party shall keep confidential all documentation and information provided by Quectel, except when the specific permission has been granted by Quectel. The Receiving Party shall not access or use Quectel’s documentation and information for any purpose except as expressly provided herein. Furthermore, the Receiving Party shall not disclose any of the Quectel's documentation and information to any third party without the prior written consent by Quectel. For any noncompliance to the above requirements, unauthorized use, or other illegal or malicious use of the documentation and information, Quectel will reserve the right to take legal action. Wi-Fi&Bluetooth Module Series AF51Y_Hardware_Design 2 / 47 Copyright The information contained here is proprietary technical information of Quectel. Transmitting, reproducing, disseminating and editing this document as well as using the content without permission are forbidden. Offenders will be held liable for payment of damages. All rights are reserved in the event of a patent grant or registration of a utility model or design. Copyright © Quectel Wireless Solutions Co., Ltd. 2021. All rights reserved. Wi-Fi&Bluetooth Module Series AF51Y_Hardware_Design 3 / 47 Safety Information The following safety precautions must be observed during all phases of operation, such as usage, service or repair of any cellular terminal or mobile incorporating the module. Manufacturers of the cellular terminal should notify users and operating personnel of the following safety information by incorporating these guidelines into all manuals of the product. Otherwise, Quectel assumes no liability for customers’ failure to comply with these precautions. Full attention must be given to driving at all times in order to reduce the risk of an accident. Using a mobile while driving (even with a handsfree kit) causes distraction and can lead to an accident. Please comply with laws and regulations restricting the use of wireless devices while driving. Switch off the cellular terminal or mobile before boarding an aircraft. The operation of wireless appliances in an aircraft is forbidden to prevent interference with communication systems. If the device offers an Airplane Mode, then it should be enabled prior to boarding an aircraft. Please consult the airline staff for more restrictions on the use of wireless devices on boarding the aircraft. Wireless devices may cause interference on sensitive medical equipment, so please be aware of the restrictions on the use of wireless devices when in hospitals, clinics or other healthcare facilities. Cellular terminals or mobiles operating over radio signal and cellular network cannot be guaranteed to connect in certain conditions, such as when the mobile bill is unpaid or the (U)SIM card is invalid. When emergent help is needed in such conditions, use emergency call if the device supports it. In order to make or receive a call, the cellular terminal or mobile must be switched on in a service area with adequate cellular signal strength. In an emergency, the device with emergency call function cannot be used as the only contact method considering network connection cannot be guaranteed under all circumstances. The cellular terminal or mobile contains a transceiver. When it is ON, it receives and transmits radio frequency signals. RF interference can occur if it is used close to TV sets, radios, computers or other electric equipment. In locations with explosive or potentially explosive atmospheres, obey all posted signs and turn off wireless devices such as mobile phone or other cellular terminals. Areas with explosive or potentially explosive atmospheres include fuelling areas, below decks on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Wi-Fi&Bluetooth Module Series AF51Y_Hardware_Design 4 / 47 About the Document Revision History Revision Date Author Description - 2020-12-22 Wilson PAN/ Lucas HUANG Creation of the document 1.0.0 2020-12-24 Wil…

Text truncated - open the document above for the full version.

Rev 1/26/2023 Quectel Wireless Solutions Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 10, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: XMR202303AF51Y [Quectel Wireless Solutions Co., Ltd.] (Jean Hu) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Name: Jean hu .. (2) Email: [email protected]...................... Signature:  . Rev 1/26/2023 Quectel Wireless Solutions Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: March 10, 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: XMR202303AF51Y [Quectel Wireless Solutions Co., Ltd.] (Jean Hu) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Name: Jean hu .. (2) Email: [email protected]...................... Signature:  .

Federal Communications Commission 7435 Oakland MiUs Road Colum创aMD 21046 在lUECTE4ι Subject: Certifi田t10ndøsignating a U.8. agent for servJce of pro佣目pursuantto Part 2.911(d)(7) Towhom忧may∞ncem， Quectel Wireless Solutlons Company limited, Grantee Code: XMR ("the appllcant可回而霄esthat, as of the date 01 the filing of app四tion，lk。国kUSA，I时IFRN: 003335033唱('theagent可isdesignated as the U.S. agent fOf the pu巾。seofa∞epting service of process on behalf of the appli四川 The phys也alU.5 . address and email 10r the designaled agent are Physical U .8. addr&幽9920Pac而cHeights Blvd., Ste. 150, #7025, San四吨。，CA92121 Email: ∞mpliance@ikotek..∞m The appticant ac回回sto maintain an agent fOf service of process in the United States for no les$ than one year after either the grantee has permane川Iyterminaled all ma毗etìngand阳p。由tion01 the appl四bleequipment 恻thinthe U.S., or the conclusion 01 any Commission.related administrative or judicial proceeding involving the eqUlpmen忧，whichever Is later. The agent ac国ptsthe designation by (the applicant) as the U.S. agent to accept service 01 pr田essincludes, oot Is not limited to, d创i晴ryof any∞rresponden出，notices, orders, decisions, and陪quirements01 administrative , legal, or judicial process related to Commission pro晤时Ings Signed by the Applicant Email: [email protected] Date: 16 Februa叩2023 Signed by the Agent (i1 d汗1erentfrom the Applicant) rF二7"""'::可-、 、、J一-' ~町百二酬M.Peterson Trtle: President and CE。 Email; joe.pete陌[email protected] Date: Feb阳ary17 th , 2023

RF_160, Issue 04 Quectel Wireless Solutions Co., Ltd. Declaration of Authorization We Name: Quectel Wireless Solutions Co., Ltd. Address: Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai, China 200233 City: Shanghai Country: China Declare that: Name Representative of agent: Well Wei Agent Company name: SGS-CSTC Standards Technical Services (Suzhou) Co., Ltd Branch Address: South of No. 6 Plant, No. 1, Runsheng Road, Suzhou Industrial Park, Suzhou Area, China (Jiangsu) Pilot Free Trade Zone City: Suzhou Country China is authorized to apply for Certification of the following product(s): Product description: Wi-Fi & Bluetooth Module Type designation: Trademark: FCC ID: AF51Y QUECTEL XMR202303AF51Y on our behalf. Sincerely yours, Contact Person: Jean Hu Applicant: Quectel Wireless Solutions Co., Ltd. Phone: +86-21-51086236 E-Mail: [email protected] Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

Quectel Wireless Solutions Co., Ltd. Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai, China 200233 Tel: +8602150086326; Fax: +862153253668 Date: March 10, 2023 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for Confidentiality FCC ID: XMR202303AF51Y To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. ⚫Schematic Diagram ⚫Block Diagram ⚫Part List ⚫Operational Description ⚫Tune-up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’ s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. ⚫External Photos ⚫Internal Photos ⚫Test Setup Photos ⚫User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Jean Hu [email protected]

Modular Approval Request FCC FCC ID: XMR202303AF51Y Items to be covered Answer from applicant 1.The modular transmitter must have its own RF shielding. Y The EUT provides the RF shielding. See EUT photo. 2.The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Y The EUT has its buffered modulation. 3.The modular transmitter must have its own power supply regulation. Y The EUT has its own power supply regulation, please see the Schematic Diagram. 4.The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. Y The EUT meets the FCC antenna requirements; unique antenna connector and photo of antenna are shown in the test report. 5.The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Y The EUT was tested with a test board, Please see test report and setup photo 6.The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. Y The FCC ID is XMR202303AF51Y 7.The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. Y The EUT is compliant with all applicable FCC rules. Details instructions for maintaining compliance are give in the User Manual. 8.The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, Y The EUT complies with RF exposure requirement. typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). Name and surname of applicant (or authorized representative): Jean Hu Date: 2023-03-10 Signature:

Quectel Wireless Solutions Co., Ltd. Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai, China 200233 UNII Declaration Letter We have declared below featured for FCC equipment authorization, device FCC ID: XMR202303AF51Y (1) DFS Device -- Master, Client with Radar detection capability , Client without radar detection capability, N/A (2) Active / Passive Scanning , adhoc mode access point capability Frequency Band (MHz) Active Scanning (the device can transmit a probe (beacon)) passive scanning (where the device is can listen only with no probes) Ad Hoc Mode capability Access point capability 2412 – 2462 MHz Yes, No Yes, No Yes, No Yes, No 2422 – 2452 MHz Yes, No Yes, No Yes, No Yes, No 5745 – 5825 MHz Yes, No Yes, No Yes, No Yes, No 5755 – 5795 MHz Yes, No Yes, No Yes, No Yes, No 5180 – 5240 MHz Yes, No Yes, No Yes, No Yes, No 5190 – 5230 MHz Yes, No Yes, No Yes, No Yes, No 5260 – 5320 MHz Yes, No Yes, No Yes, No Yes, No 5270 – 5310 MHz Yes, No Yes, No Yes, No Yes, No 5500 – 5700 MHz Yes, No Yes, No Yes, No Yes, No 5510 – 5670 MHz Yes, No Yes, No Yes, No Yes, No (3) Country code selection ability - Yes , No If no, pls explain how was implemented : use Microsoft network utility (4) Meet 15.202 requirement - Yes , No , pls check below : A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. (5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. Apply , No Apply , (If apply , pls help to provide explanation on how it was implement (By hardware or software , and how software was controlled) If you have any questions, please feel free to contact me at the address shown below. Yours sincerely, Signatory Quectel Wireless Solutions Co., Ltd. Printed Name:Jean hu

Page 1 of 4 1 Photographs - EUT Constructional Details Test auxiliary PCB board and surrounding photos Page 2 of 4 Page 3 of 4 Page 4 of 4 Model No.: AF51Y FCC ID: XMR202303AF51Y

Label

Page 1 of 1 1 Photographs - EUT Constructional Details Model No.: AF51Y FCC ID: XMR202303AF51Y

` SGS-CSTC Standards Technical Services (Suzhou) Co., Ltd. Report No.: SEWA2301000005RG06 Rev.: 01 Page: 1 of 8 Authorized Signature: Panta Sun Wireless Laboratory Manager TEST REPORT Application No.: SEWA2301000005RG Applicant: Quectel Wireless Solutions Co., Ltd. Address of Applicant: Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai, China 200233 Manufacturer: Quectel Wireless Solutions Co., Ltd. Address of Manufacturer: Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai, China 200233 EUT Description: Wi-Fi & Bluetooth Module Model No.: AF51Y Trade Mark: Quectel FCC ID: XMR202303AF51Y Standards: 47 CFR Part 2.1091 FCC KDB 447498 D01 v06 Date of Receipt: 2023/01/09 Date of Issue: 2023/02/23 Test Result: PASS* * In the configuration tested, the EUT complied with the standards specified above. ` SGS-CSTC Standards Technical Services (Suzhou) Co., Ltd. Report No.: SEWA2301000005RG06 Rev.: 01 Page: 2 of 8 1 Version Revision Record Version Chapter Date Modifier Remark 01 2023/02/23 Original Prepared By (Nick Hu) / Test Engineer Checked By (Well Wei) / Reviewer ` SGS-CSTC Standards Technical Services (Suzhou) Co., Ltd. Report No.: SEWA2301000005RG06 Rev.: 01 Page: 3 of 8 Contents 1 Version ......................................................................................................................... 2 2 General Information ...................................................................................................... 4 2.1 Client Information .................................................................................................. 4 2.2 Test Facility ........................................................................................................... 4 2.3 General Description of EUT ................................................................................... 5 3 RF Exposure Evaluation ............................................................................................... 6 3.1 RF Exposure Compliance Requirement ................................................................ 6 3.1.1 Limits ................................................................................................................. 6 3.1.2 Test Procedure .................................................................................................. 7 3.1.3 EUT RF Exposure Evaluation ............................................................................ 7 3.1.4 Exposure calculations for multiple sources ........................................................ 8 ` SGS-CSTC Standards Technical Services (Suzhou) Co., Ltd. Report No.: SEWA2301000005RG06 Rev.: 01 Page: 4 of 8 2 General Information 2.1 Client Information Applicant: Quectel Wireless Solutions Co., Ltd. Address of Applicant: Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai, China 200233 Manufacturer: Quectel Wireless Solutions Co., Ltd. Address of Manufacturer: Building 5, Shanghai Business Park Phase III (Area B), No.1016 Tianlin Road, Minhang District, Shanghai, China 200233 2.2 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 6336.01) SGS-CSTC STANDARDS TECHNICAL SERVICES (SUZHOU) CO., LTD. is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 6336.01. • Innovation, Science and Economic Development Canada SGS-CSTC STANDARDS TECHNICAL SERVICES (SUZHOU) CO., LTD. has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0120. IC#: 27594. • FCC –Designation Number: CN1312 SGS-CSTC STANDARDS TECHNICAL SERVICES (SUZHOU) CO., LTD. has been recognized as an accredited testing laboratory. Designation Number: CN1312. Test Firm Registration Number: 717327 ` SGS-CSTC Standards Technical Services (Suzhou) Co., Ltd. Report No.: SEWA2301000005RG06 Rev.: 01 Page: 5 of 8 2.3 General Description of EUT EUT Description: Wi-Fi & Bluetooth Module Model No.: AF51Y Trade Mark: Quectel Hardware Version: R1.0 Software Version: NA Antenna Type: External Antenna Antenna Gain: BT/BLE: 3.44dBi (Ant0) 2.4G WIFI: 3.44dBi (Ant0); 5.26dBi (Ant1) 5150MHz to 5250MHz: 3.16dBi (Ant0); 3.26dBi (Ant1) 5250MHz to 5350MHz: 3.35dBi (Ant0); 3.26dBi (Ant1) 5470MHz to 5725MHz: 3.26dBi (Ant0); 3.28dBi (Ant1) 5725MHz to 5850MHz: 2.96dBi (Ant0); 3.24dBi (Ant1) Note: The antenna gain are derived from the gain information report provided by the manufacturer. Remark: As above information is provided and confirmed by the applicant. SGS is not liable to the accuracy, suitability, reliability or/and integrity of the information. ` SGS-CSTC Standards Technical Services (Suzhou) Co., Ltd. Report No.: SEWA2301000005RG06 Rev.: 01 Page: 6 of 8 3 RF Exposure Evaluation 3.1 RF Exposure Compliance Requirement 3.1.1 Limits Frequency range (MHz) Electric field strength (V/m) Magnetic field strength (A/m) Power density (mW/cm2) Averaging time (minutes) (A) Limits for Occupational/Controlled Exposures 0.3-3.0 614 1.63 *(100) 6 3.0-30 1842/f 4.89/f *(900/f2) 6 30-300 61.4 0.163 1.0 6 300-1500 / / f/300 6 1500-100,000 / / 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f2) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 F=frequency in MHz *=Plane-wave equivalent power density RF exposure compliance will need to be determined with respect to 1.1307(c) and (d) of the FCC rules. The emissions should be within the limits at 300kHz in Table 1 of 1.1310(use the 300kHz limits for 150kHz:614V/m,1.63A/m). Friis Formula Friis transmission formula: Pd = (Pout*G)/(4* Pi * R 2 ) Where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 …

Text truncated - open the document above for the full version.

CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Page 1 of 35 © Copyright by CETECOM Total Radiated Power and Total Isotropic Sensitivity Spherical Pattern Measurement. TESLA WiFi#3 Antenna REPORT Date of Report: 2022-12-01 Date of issue: 2022-12-01 Report Copy No.: 1.0 The test results of this test report relate exclusively to the test item specified in Identification of the Equipment under Investigation. The CETECOM Inc. USA does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the CETECOM Inc USA. CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Page 2 of 35 © Copyright by CETECOM Manufacturer Tesla Model WiFi Antenna #3 CTIA Request # N/A Wi-Fi Alliance CID # N/A EUT ID / SN / IMEI N/A FCC ID Number N/A Hardware Version N/A Software Version N/A Configuration of Primary Mechanical Mode Unit in Freespace position Test Plan Revision N/A Test date 11/18/2022 Temperature / Humidity 72.7 0 F / 47.1% Applicant’s Name: TESLA INC Address: 3500 Deer Creek Rd, Palo Alto, CA 94304 Contact Person: Peng Zhang Phone No. 510-213-1367 Fax: N/A e-mail: [email protected] CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Page 3 of 35 © Copyright by CETECOM EUTs used for each test EUT # EUT ID CATL/CHAMBER USED Radio Modes Band(s) Test Types(s) Test Conditions 1 WiFi #3 CETECOM/OTA5 Passive antenna 2.4 GHz / 5 Ghz Gain FS CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2113686 Page 4 of 35 © Copyright by CETECOM  Contents 1 SUMMATION TEST REPORT – Gain measurements .................................................................................................................................. 6 2 Physical Layout and Site Description .............................................................................................................................................................. 8 2.1 Wireless Test Facility ................................................................................................................................................................................... 8 2.2 Anechoic Chamber........................................................................................................................................................................................ 8 2.3 Phi Axis Positioner & Theta Axis Scanner ................................................................................................................................................... 9 2.4 Wrist-Worn Forearm Phantom .................................................................................................................................................................... 9 2.5 Quiet Zone .................................................................................................................................................................................................... 9 2.6 Howland Company Model QR-4 Quad Ridge Horn Antenna .................................................................................................................... 10 2.7 Circularly Polarized Communication Antenna ........................................................................................................................................... 10 2.8 Test Equipment ........................................................................................................................................................................................... 10 2.9 AMS32 Software ........................................................................................................................................................................................ 11 3 Test Method ................................................................................................................................................................................................... 12 3.1 Total Radiated Power .................................................................................................................................................................................. 12 3.2 Total Isotropic Sensitivity ................................................…

Text truncated - open the document above for the full version.