XR3-GO103GENIIE Ink Tablet, ePaper Tablet, Digital Paper, Note-taking Tablet, Digital Writing Tablet, E reader, Paper tablet, eBook reader

5GHz band(W52, W53): Indoor use only Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. IC Caution:： This device complies with Innovation, Science, and Economic Development Canad licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. FCC/IC Radiation Exposure Statement: The device has been tested and comply with FCC/ISED SAR limits. L'Unité a été testée et répond aux limites FCC/ISED SAR. Any devices capable of operating in the band 5150-5250MHz shall only be used indoors to reduce the potential for harmful interference to co-channel mobile satellite systems (this requirement does not apply to OEM devices installed in vehicles by vehicle manufacturers) RemarqueÿBande 5GHz (W52, W53): utilisation intérieure uniquement Tout dispositif capable de fonctionner dans la bande 5150-5250 MHz ne doit être utilisé qu'à l'intérieur pour réduire le potentiel d'interférence nuisible pour les systèmes mobiles satellitaires co-canalisés (cette exigence ne s'applique pas aux dispositifs OEM installés dans les véhicules par les constructeurs de véhicules). HVIN: Go 10.3 (Gen II), BOOX Go 10.3 (Gen II) Lumi, BOOX Go 10.3 (Gen II) Plus, BOOX Go 10.3 (Gen II) Pro, BOOX Go 10.3 (Gen II) Lite, BOOX Go Color 10.3, BOOX Go Color 10.3 Plus, BOOX Go Color 10.3 Pro

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-RF-INP Page 29 of 48 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-RF-INP Page 30 of 48 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-RF-INP Page 31 of 48 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-RF-INP Page 32 of 48 BOOX Go Color 10.3 ANT Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-RF-INP Page 33 of 48 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-RF-INP Page 34 of 48 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-RF-INP Page 35 of 48

Bay Area Compliance Laboratories Corp. (Shenzhen) EXHIBIT No.: 2601P93961E-RF-TSPA Page 1 / 4 TEST SETUP PHOTOGRAPHS Conducted Emissions - Front View Conducted Emissions - Side View Bay Area Compliance Laboratories Corp. (Shenzhen) EXHIBIT No.: 2601P93961E-RF-TSPA Page 2 / 4 Radiated Emissions View (Below 30MHz) Radiated Emissions View (Below 1GHz) Bay Area Compliance Laboratories Corp. (Shenzhen) EXHIBIT No.: 2601P93961E-RF-TSPA Page 3 / 4 Radiated Emissions View (1-18 GHz) Radiated Emissions View (18-25 GHz) Bay Area Compliance Laboratories Corp. (Shenzhen) EXHIBIT No.: 2601P93961E-RF-TSPA Page 4 / 4 RF Conducted View *****END *****

-1- VERSION INFORMATION PECIFICATION FOR APPROVAL CUSTOMER：ONYX INTERNATIONAL INC. CUSTOMER PARTNO：OAN.OAN0070R SUPPLIER：MyAntenna RF Technology CO., LTD PRODUCT MODEL：Goat10 PRODUCT NAME：Goat10 PRODUCT CODE：M01-0201270R0A CUSTOMER SIGNATURE：CUSTOMER SEAL： SUPPLIER SIGNATURE： SUPPLIERSEAL ： NOTE: PLEASE RETURN THIS COPY AS A CERTIFICATION OF YOUR APPROVAL！ Prepared by： Dong chunling Date： 2024-03-20 Add： 410, Building A, Fenghuang Zhigu, No. 50 Tiezai Road, Gongle Community, Xixiang Street, Bao'an District, Shenzhen City, Guangdong Province. Tel:0755-86503881 -2- Version DATE REVISION DESCRIPTION PREPARED CHECKED APPROVED V1.02024-03-20 First edition Dong Chunling Huang Wenhua Chen Jianyou PERFORMANCE PARAMETER -3- 1.Electrical Characteristics Antenna 1Antenna model Omnidirectional antenna 2Frequency Range 2400-2500MHz/5100-5900MHz 3V.S.W.R≤3.0 4Peak Gain4.59dBi 5Peak Efficiency58.3% 6Impendence50Ω 7Polarization Linearly Polarized Antenna 2.Material NoPart Name 1FPCFPC Black FPC 2RF CableΦ0.81BlackΦ0.81 3RF ConnectorIpex 3 Golden Ipex 3 PERFORMANCE PARAMETER -4- 3.Environment Condition 1Working Temp-40°C～+85°C, 10%～95% RH 2Storage Temp-55°C～+100°C, 10%～95% RH 4.environmental requirements： 1 environmental requirements ROHS/REACH Whether it is necessary to comply with the ROHS/REACH Comply Other requirements - 5.Environmental compliance requirements ： S/N Test itemsReference standards test method Test conditions Qualification judgment 1low temperature storage ETSI 300019-2-4 YD/T 1059 IEC 60068-2 -1 GB/T 2423.1 Place the sample at room hours.Place the sample at room temperature, cool to – 40 °C, maintain this temperature for 24 hours, then allow it to warm up for 2 hours. Following the test, all product specifications , functions and mechanical properties were found to be normal at room temperature. -5- 2high temperature storage ETSI 300019-2-4 YD/T 1059 IEC 60068-2 -2 GB/T 2423.2 70 °C , 24hr, 1°C/min，70°C, 24hr, 1 °C /min ， Place the sample at room temperature, heat to 70°C, maintain at this temperature for 24 hours, then cool to room temperature after 2 hours. Following the test,the product ’ s specifications , functionality and mechanical properties were all found to be normal at room temperature. -6- 3temperature cycling ETS 300019-2-4 YD/T 1059 IEC 60068-2 -14 GB/T 2423.22 -20–90 °C, 1 °C/min, held at the minimum and maximum temperatures for 3 hours, 5 cycles Following the test, the product’s specifications , functionality and mechanical properties were all found to be normal at room temperature.Fo llowing the test, the product’s specifications , functionality and mechanical properties were all found to be normal at room temperature.Fo llowing the test, the product’s specifications , functionality and mechanical properties wereallfound -7- 4saltspray test ETS 300019-2-4 DKBA4073-2009.0 3 Corrosion resistance requirements for structural products IEC 60068-2 -52 GB/T 2423.18 +15 to +35 °C, 5% ± 1% NaCl solution, pH 6.5–7.2, spray for 2 hours; 40 °C, 93% relative humidity, maintained for 22 hours, 3 cycles Once the stress has been relieved, the antenna surface should show no signs of rust, discolouration or flaking of the coating. Following the test, all product specifications , functions and mechanical properties should remain normal at room temperature. -8- TESTING CURVE 1. Performance test 1.1 V.S.W.R Data list Freq2400MHz 2500MHz 5100MHz 5850MHz VSWR2.711.931.401.19 -9- TESTING CURVE 2. Passive testing 2.1 Efficiency and Gain Freq(MHz) Gain(dBi) Efficiency(%) Freq(MHz) Gain(dBi) Efficiency(%) Efficiency Gain -10- 2400 1.8433.07 5400 3.9156.01 2410 2.2936.23 5420 4.0156.47 2420 2.7440.15 5440 4.0454.76 2430 3.1144.02 5460 4.1458.30 2440 3.5948.69 5480 4.1354.12 2450 4.0150.10 5500 3.8553.71 2460 4.2652.77 5520 3.8052.35 2470 4.4553.34 5540 3.7352.79 2480 4.5153.58 5560 4.0754.30 2490 4.5953.07 5580 4.3356.11 2500 4.5052.54 5600 4.1057.71 5100 3.0650.12 5620 4.0255.14 5120 2.8348.73 5640 3.9655.19 5140 2.8451.45 5660 4.0154.39 5160 3.0052.28 5680 4.1756.94 5180 2.9550.76 5700 4.3257.33 5200 3.2253.70 5720 4.1757.27 5220 3.4854.51 5740 4.0956.21 5240 3.3355.50 5760 3.7751.45 5260 3.2253.27 5780 3.7050.57 5280 3.1953.59 5800 3.8551.32 5300 3.3855.34 5820 3.9252.28 5320 3.6856.13 5840 3.8152.45 5340 3.7854.69 5860 3.7750.21 5360 3.9956.63 5880 3.7350.66 5380 3.9954.83 5900 3.5949.36 TESTING CURVE -11- 2.2 3D 图 3D Map 2450MHz Gain=4.01dBi 5360MHz Gain=3.99dBi -12- TESTING CURVE 5760MHz Gain=3.77dBi 2.3 2D Figure H FigureE1 FigureE2 Figure 2450MHz Gain=4.01dBi -13- H FigureE1 FigureE2 Figure 5360MHz Gain=3.99dBi 5760MHz Gain=3.77dBi 2.4 Active data 2.5 Schematic diagram of darkroom test coordinates -14- SCHEDULE DRAWING -15- 13.20±0.2 A B C D E F A B C D E F 8 7 6 5 8 7 6 5 SCALESHEET REV. 1:1 1/1 V01 DWG NO.: DR: CHKD: APPD: PART NO.: M 01-0201270R0A CUS P/N: DIM ENSIONS ARE IN M ILLIMETERS UNLESS OTHERW ISE SPECIFIED ANGLES = ±3° UP TO 6 = ±0.1 6-40 = ±0.2 40-120 = ±0.6 120-315 = ±1.0 ABOVE 315 = ±1.6 TOLERANCES TITLE: GOAT10 OAN.OAN0070R No. Nam e FPC Coaxial Line MaterialColor Black Black TreatmentAmountRemark 29.2*13.2mm1 1 1 2Φ0.81*29.0mm REV.DESCRIPTIONAPPD.DATE AINITIAL RELEASED Chen 2024/03/20 Notes： 1. Frequency range：2400-500MHz;5100-5900M Hz 2.Im pedance:50? 3.V.S.W .R:≤3.0 4.Maxim um gain:4.59dBi 7.Wire polarity: Wire polarity 9.All com ponents comply with RoHS 8.Tem perature range:-40°C- 85°C 5.Maxim um efficiency:58.3% 6.After wire soldering, the total height of the solder joints m ust not exceed 1.20 m m (including release paper) 29.20±0.3 GOAT V1.4 29.00±1.0 1 2 IPEX 4 Φ0.81±0.1 -16- Physical picture Antenna area

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn TR-EM-RF004 Page 1 of 103 Version 4.1 TEST REPORT Applicant Name:ONYX INTERNATIONAL INC. Address:Room 101, Building 4, No. 202 Shiyu Road, Nansha District, Guangzhou City, Guangdong Province,China Report Number:2601P93961E-RF-00A FCC ID:XR3-GO103GENII Test Standard (s) FCC PART 15.247 Sample Description Product Type:E Ink Tablet, ePaper Tablet, Digital Paper, Note-taking Tablet, Digital Writing Tablet, E reader, Paper tablet, eBook reader Model No.:Go 10.3 (Gen II) Multiple Model(s) No.:BOOX Go 10.3 (Gen II) Lumi, BOOX Go 10.3 (Gen II) Plus, BOOX Go 10.3 (Gen II) Pro, BOOX Go 10.3 (Gen II) Lite, BOOX Go Color 10.3, BOOX Go Color 10.3 Plus, BOOX Go Color 10.3 Pro Trade Mark:BOOX Date Received:2026-01-05 Issue Date:2026-03-23 Test Result:Pass ▲ ▲ In the configuration tested, the EUT complied with the standards above. Prepared and Checked By:Approved By: Wills YuNancy Wang RF EngineerRF Supervisor Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-RF-00A TR-EM-RF004 Page 2 of 103 Version 4.1 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ..........................................................................................................................3 GENERAL INFORMATION ........................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)......................................................................................4 OBJECTIVE ....................................................................................................................................................................4 TEST METHODOLOGY....................................................................................................................................................4 MEASUREMENT UNCERTAINTY .....................................................................................................................................5 TEST FACILITY ..............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ...........................................................................................................................6 SUMMARY OF TEST RESULTS ................................................................................................................................9 TEST EQUIPMENT LIST ..........................................................................................................................................10 REQUIREMENTS AND TEST PROCEDURES ......................................................................................................12 AC LINE CONDUCTED EMISSIONS...............................................................................................................................12 SPURIOUS EMISSIONS ..................................................................................................................................................14 6 DB EMISSION BANDWIDTH & 99% OCCUPIED BANDWIDTH ....................................................................................17 MAXIMUM CONDUCTED OUTPUT POWER ...................................................................................................................19 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE....................................................................................................20 CONDUCTED SPURIOUS EMISSION...............................................................................................................................21 POWER SPECTRAL DENSITY ........................................................................................................................................22 DUTY CYCLE ...............................................................................................................................................................25 ANTENNA REQUIREMENT .....................................................................................................................................26 TEST DATA AND RESULTS .....................................................................................................................................27 AC LINE CONDUCTED EMISSIONS...............................................................................................................................27 SPURIOUS EMISSIONS ..................................................................................................................................................30 RF CONDUCTED DATA ................................................................................................................................................84 6dB Emission Bandwidth...........................................................…

Text truncated - open the document above for the full version.

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn TR-EM-RF003 Page 1 of 79 Version 4.1 TEST REPORT Applicant Name:ONYX INTERNATIONAL INC. Address:Room 101, Building 4, No. 202 Shiyu Road, Nansha District, Guangzhou City, Guangdong Province,China Report Number:2601P93961E-RF-00C FCC ID:XR3-GO103GENII Test Standard (s) FCC PART 15.247 Sample Description Product Type:E Ink Tablet, ePaper Tablet, Digital Paper, Note-taking Tablet, Digital Writing Tablet, E reader, Paper tablet, eBook reader Model No.:Go 10.3 (Gen II) Multiple Model(s) No.:BOOX Go 10.3 (Gen II) Lumi, BOOX Go 10.3 (Gen II) Plus, BOOX Go 10.3 (Gen II) Pro, BOOX Go 10.3 (Gen II) Lite, BOOX Go Color 10.3, BOOX Go Color 10.3 Plus, BOOX Go Color 10.3 Pro Trade Mark:BOOX Date Received:2026-01-05 Issue Date:2026-03-23 Test Result:Pass ▲ ▲ In the configuration tested, the EUT complied with the standards above. Prepared and Checked By:Approved By: Wills YuNancy Wang RF EngineerRF Supervisor Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-RF-00C TR-EM-RF003 Page 2 of 79 Version 4.1 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ..........................................................................................................................3 GENERAL INFORMATION ........................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)......................................................................................4 OBJECTIVE ....................................................................................................................................................................4 TEST METHODOLOGY....................................................................................................................................................4 MEASUREMENT UNCERTAINTY .....................................................................................................................................5 TEST FACILITY ..............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ...........................................................................................................................6 SUMMARY OF TEST RESULTS ................................................................................................................................9 TEST EQUIPMENT LIST ..........................................................................................................................................10 REQUIREMENTS AND TEST PROCEDURES ......................................................................................................12 AC LINE CONDUCTED EMISSIONS...............................................................................................................................12 UNWANTED EMISSION FREQUENCIES AND RESTRICTED BANDS .................................................................................14 6 DB EMISSION BANDWIDTH & 99% OCCUPIED BANDWIDTH....................................................................................17 PEAK OUTPUT POWER MEASUREMENT .......................................................................................................................19 POWER SPECTRAL DENSITY ........................................................................................................................................20 100 KHZ BANDWIDTH OF FREQUENCY BAND EDGE....................................................................................................21 CONDUCTED SPURIOUS EMISSION...............................................................................................................................22 DUTY CYCLE ...............................................................................................................................................................23 ANTENNA REQUIREMENT .....................................................................................................................................24 TEST DATA AND RESULTS .....................................................................................................................................25 AC LINE CONDUCTED EMISSIONS...............................................................................................................................25 UNWANTED EMISSION FREQUENCIES AND RESTRICTED BANDS .................................................................................28 RF CONDUCTED DATA ................................................................................................................................................64 6dB Emission Bandwidth.............................................................................................................................…

Text truncated - open the document above for the full version.

Note: The information marked # is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP or any agency of the U.S. Government. This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “▼”. Bay Area Compliance Laboratories Corp. (Shenzhen) 5F(B-West) , 6F, 7F, the 3rd Phase of Wan Li Industrial Building D, Shihua Rd, FuTian Free Trade Zone, Shenzhen, China Tel: +86-755-33320018Fax: +86-755-33320008www.baclcorp.com.cn TR-EM-SA005 Page 1 of 48 Version 3.0 TEST REPORT Applicant Name: ONYX INTERNATIONAL INC. Address: Room 101, Building 4, No. 202 Shiyu Road, Nansha District, Guangzhou City, Guangdong Province, China Report Number: 2601P93961E-SAA FCC ID: XR3-GO103GENII Test Standard (s) FCC 47 CFR part 2.1093 Sample Description Product Name: E Ink Tablet, ePaper Tablet, Digital Paper, Note-taking Tablet, Digital Writing Tablet, E reader, Paper tablet, eBook reader Model No.: Go 10.3 (Gen II) Multiple Model(s) No.: BOOX Go 10.3 (Gen II) Lumi, BOOX Go 10.3 (Gen II) Plus, BOOX Go 10.3 (Gen II) Pro, BOOX Go 10.3 (Gen II) Lite, BOOX Go Color 10.3, BOOX Go Color 10.3 Plus, BOOX Go Color 10.3 Pro Trade Mark: BOOX Date of Test: 2026/03/07~2026/03/08 Issue Date: 2026/03/15 Test Result: Pass ▲ ▲In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Bob Lu Luke Jiang SAR Engineer SAR Engineer Bay Area Compliance Laboratories Corp.(Shenzhen) Report No.: 2601P93961E-SAA TR-EM-SA005 Page 2 of 48 Version 3.0 Attestation of Test Results MODE Max. SAR Level(s) Reported(W/kg) Limit (W/kg) WLAN 2.4G 1g Body SAR 0.78 1.6 WLAN 5.2G 1g Body SAR 0.79 WLAN 5.3G 1g Body SAR 0.77 WLAN 5.6G 1g Body SAR 0.79 WLAN 5.8G 1g Body SAR 0.48 Bluetooth 1g Body SAR 0.08 Applicable Standards FCC 47 CFR part 2.1093 Radiation exposure evaluation: portable devices IEEE 1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques KDB procedures KDB 447498 D01 General RF Exposure Guidance v06 KDB 616217 D04 SAR for laptop and tablets v01r02 KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04 KDB 865664 D02 RF Exposure Reporting v01r02 KDB 248227 D01 802 11 Wi-Fi SAR v02r02 Note: This wireless device has been shown to be capable of compliance for localized specific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures. The results and statements contained in this report pertain only to the device(s) evaluated. Note: In this case the EUT (Equipment Under Test) is set 0mm away from the phantom, the test distance is 0mm for body. Bay Area Compliance Laboratories Corp.(Shenzhen) Report No.: 2601P93961E-SAA TR-EM-SA005 Page 3 of 48 Version 3.0 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 EUT DESCRIPTION ................................................................................................................................................... 5 TECHNICAL SPECIFICATION ......................................................................................................................................... 5 REFERENCE, STANDARDS, AND GUILDELINES .............................................................................................. 6 SAR LIMITS ................................................................................................................................................................ 6 FACILITIES ................................................................................................................................................................. 7 DESCRIPTION OF TEST SYSTEM .......................................................................................................................... 8 EQUIPMENT LIST AND CALIBRATION ............................................................................................................. 15 EQUIPMENT’S LIST & CALIBRATION INFORMATION .................................................................................................. 15 SAR MEASUREMENT SYSTEM VERIFICATION ............................................................................................. 16 LIQUID VERIFICATION ............................................................................................................................................... 16 SYSTEM ACCURACY VERIFICATION .......................................................................................................................... 18 SAR SYSTEM VALIDATION DATA .................................................................................................................... 19 EUT TEST STRATEGY AND METHODOLOGY ................................................................................................. 23 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS ............................................................................. 23 TEST DISTANCE FOR SAR EVALUATION .............................................................................................…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-SAA TR-EM-SA005 Page 1 of 11 Version 3.0 APPENDIX D RETURN LOSS&IMPEDANCE MEASUREMENT Equipment Details: Description: Dipole Manufacturer: Speag Model Number: D2450V2 Serial Number: 1103 Calibration Date: 2024/03/27 Calibrated By: Bob Lu Signature: All Calibration have been conducted in the closed laboratory facility: Lab Temperature 18°C-25°C and humidity < 70% Calibrated Equipment: Equipment Model S/N Calibration Date Calibration Due Date Simulated Tissue Liquid Head HBBL600-10000V62200808-2 Each Time SAM Twin Phantom SAM-Twin V8.0 1962 NCR NCR Network Analyzer E5071C SER MY46519680 2023/06/08 2024/06/07 Network Analyzer Calibration Kit 50Ω 51026 NCR NCR Test Data: Frequency (MHz) Simulated Liquid Parameter Measured Value Target Value Deviation Reference Range Results 2450 Head Return Loss 25.308 dB 24.161 dB 4.747 % ±20%;≥20dB Pass Real Impedance 56.592 Ω 53.467 Ω 3.125 Ω ≤5Ω Pass Imaginary Impedance 0.829 Ω 5.400 Ω -4.571 Ω ≤5Ω Pass Note: Return Loss Deviation = (Measured-Target)/Target×100% Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-SAA TR-EM-SA005 Page 2 of 11 Version 3.0 Dipole, 2450MHz, 1103 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: 2601P93961E-SAA TR-EM-SA005 Page 3 of 11 Version 3.0 Equipment Details: Description: Dipole Manufacturer: Speag Model Number: D2450V2 Serial Number: 1103 Calibration Date: 2025/03/26 Calibrated By: Bob Lu Signature: All Calibration have been conducted in the closed laboratory facility: Lab Temperature 18°C-25°C and humidity < 70% Calibrated Equipment: Equipment Model S/N Calibration Date Calibration Due Date Simulated Tiss…

Text truncated - open the document above for the full version.